User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
4265.DOC020102
2-2
Edition July 2015
2.1.1 Display
The display is a high - resolution, TFT (Thin Film Transistor) flat screen, color
monitor. It shows Radar targets and data as well as a number of menus and
software buttons. The Radar system can be used with the display sizes of 19”,
23.1”, 26” and 27”.
2.1.2 Trackball
When using the trackball, the cursor is moved by rolling the ball in the
appropriate direction.
The trackball -guided cursor is the central control instrument for operating this
Radar.
Figure 2-2 Trackball
Pos. No.
Task
1
The left trackball button is used as the Enter key.
Using the trackball, place the cursor over a soft button from
the menu and press the button. The soft button function is
activated (chapter 0).
Using the trackball, place the cursor over a text line (e.g. SET,
DRIFT) or a toggle field with slider function. Press the left
trackball button until the slider symbol appears (yellow
rectangle) below the toggle field. Moving the trackball
horizontally will adjust the slider below the text line and a
value is displayed (chapter 2.1.4.1).
Using the trackball, place the cursor over a slider (e.g. GAIN)
press the left trackball button and move the trackball. The
colored slider will follow the trackball to the left or the right.
Pressing the
left
trackball button again the actual slider
1
2
3