User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
4265.DOC020102
2-22
Edition July 2015
Operator controls
Text identifier
Radar Transceiver Status.
Example;
This Radar is connected to Transceiver XCVR2.
This Radar is used as X-BAND Radar.
This Radar is used as MASTER under X-BAND
condition.
2.2.1.1 System Configuration Diagram
The system configuration diagram displays the actual setup and can be used to
connect the own Display (A, B, C..) to any Transceiver (1 MK2, 2 MK2 …..) as
Master or Slave. The connection will be realized per link.
A line symbol between the display and the transceiver shows the link.
A dashed line indicates a connection link in progress.
A continuous line indicates an active link.
The operator can choose between the application Display (A, B, ... ) in Master
mode or Slave mode. The Transceiver symbols are equipped with two
connection points.
M for Master mode
S for Slave mode
Within a Radar system each Transceiver can only be controlled by one display
in Master mode at the same time. The other display can control the transceiver
in Slave Mode only.
Master control.
When M is selected, the transceiver will respond if no other display is already
Master.
Master control allows Pulse length Control, PMU operation, and Sector
Blanking Control.
Transceiver Warm Up time may appear, the total POWER ON time of the
scanner, and MAG SEND TIME.