User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
Edition July 2015
2-99
4265.DOC020102
2.3.4.6 Editing EBL and VRM
The EBL and/or VRM can be placed and changed using the cursor or the
Operator Panel.
When using the Operator Panel, you are restricted to the EBL1 and VRM1
group. The Radar provides 3 options for editing the EBL/VRM.
In the EBL/VRM menu the navigator options for EBL/VRM can be switched over
for the BASE POINT between POSITION FIXED and OWNSHIP FIXED, for the
ALIGNMENT between OWNSHIP STABILIZED and NORTH STABILIZED.
These settings have to be done before editing EBL/VRM.
Operator controls
Task
Cursor
In this example, the EBL1 is shown, starting from the
current position of the ship. Position the cursor on the
desired target and press the right trackball button. This
places EBL1.
Select the Offset toggle field (CENT/FLOAT) if EBL1 is to
be moved parallel. Pressing the left trackball button moves
EBL1 to the new position.
Bearing with Cursor
Place the cursor on EBL 1, press the right trackball button.
Find the desired target and press the left trackball button
(Figure 2-33).