User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
4265.DOC020102
2-110
Edition July 2015
Operator controls
Task
Speed (SPD). The type of sensor in use is indicated on
the button (e.g. LOG1(WT)). (WT for Water Track, BT for
Bottom Track).
Step 1 Select the LOG1(WT) soft button.
The Speed Selection Menu appears in the function
display.
Step 2 Press the SOG soft button.
The SOG Sensor Select menu appears in the function
display, showing the available speed sensors in this
system. Pressing the DISABLED soft button the
stabilization mode changes to LOG1(WT) the indication
changes to CTW and STW for sea stabilization.
In MAN mode the sensor can be selected by the user. If
no sensor is available a manual SOG value can be
entered.
To set MANUAL input, use the slider function inside the
numerical field.
Step 3 Select the STW soft button.
The STW Sensor Select window appears in the function
display, showing the available speed sensors in this
system. (The interfaced LOG sensor must be a DUAL
AXIS LOG sensor, a single axis log cannot detected the
effect leeway). Pressing the DISABLED soft button the
stabilization mode changed to LOG1(BT) the indication
changed to COG and SOG for ground stabilization.
In MAN mode the sensor can be selected by the user. If
no sensor is available a manual STW value can be used.
To set MANUAL input, use the slider function inside the
numeric indicator.