SPARK™ SERIES SCOOTERS OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 22 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts.
CONTENTS Safety Warnings............................................................................................... 1 Before You Begin.............................................................................................. 2 Assembly and Set-up.....................................................................................3-5 Pre-Ride Checklist and Usage........................................................................... 6 Repair and Maintenance........................................
BEFORE YOU BEGIN Remove contents from box. Remove the packing material used to protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint and dents that may have occurred during shipping. Because your scooter is assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. Handlebars WARNING: DO NOT USE NON-RAZOR PRODUCTS WITH YOUR SCOOTER.
ASSEMBLY AND SET-UP Folding and Unfolding the Scooter WARNING: Keep fingers clear of the folding mechanism when folding or unfolding the scooter. Make sure others are standing clear. 1 To release the folding mechanism, place the scooter on the ground and place one foot on the deck plate. Push the joint-release lever down (to raise) or up (to lower) the T-bar until it is securely locked in the desired upright or folded position for riding or storage.
ASSEMBLY AND SET-UP 1. Install the AAA batteriesmodels when open the box Adjusting the Handlebar Height (Select only) Required Tool: Cross Screwdriver (Included) WARNING: Failure to properly secure the quick-release lever may cause the T-bar to telescope up or down while riding and may cause you to lose control and fall. 1 To adjust the height of the handlebars, open the quick-release lever and slide the T-bar to the desired position. Close the quick-release lever to lock into place.
ASSEMBLY AND SET-UP Assembling the T-bar (S Spark only) WARNING: Failure to properly install and tighten the pivoting mechanism and the plastic cover may cause the rider to lose control and fall. If you do not understand these instructions, contact Razor customer care for assistance. WARNING: Do not attempt to thread the handlebar into the front fork thread. Tighten clamp securely. 5mm 1 Loosen the collar clamp and slide it upward. Insert T-bar into the fork until it bottoms out on the headset locknut.
PRE-RIDE CHECKLIST Loose Parts Be Careful! You will see people on TV and maybe even people you know doing tricks and stunts. These are people who have been practicing on scooters for a very long time. Don’t try something until you are ready. Avoid steep inclines and don’t ride too fast — you can lose control and fall. Skateboard parks are not designed for scooters.
the AAA batteries 2. Replace REPAIR AND MAINTENANCE Required Tool: Cross Screwdriver (Included) q Replacing the Spark Cartridge WARNING: Do not attempt to replace cartridge immediately after riding as cartridge will be hot. Handle only when cool. Friction during sparking will eventually wear out the replaceable cartridge and cause the scooter to stop making sparks. Worn out cartridges should be replaced to avoid damaging the Spark Bar. WARNING: Keep fingers clear of Spark Bar hinge and fender brake.
REPAIR AND MAINTENANCE Wheels and Bearings Under normal circumstances and conditions, Razor wheels and wheel bearings are maintenance free. Nonetheless, it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper tightness, and bearings for side-to-side play, and loose parts. When a wheel or wheel bearing develops play, this is an indication of excess wear and replacement is necessary. Replace immediately with only genuine Razor wheels.
SPARK SCOOTER PARTS LIST Keep your Spark scooter running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Grips 9. 2. Handlebars 3. T-Bar 10. Wheels (Front/Rear) (Lighted Wheels for Spark DLX, Spark 2.0 and Spark+ only) (Ultra Bright Wheels for Spark Ultra only) 4. Quick-Release Lever (Select models only) 11. Spark Bar 5. Extension Tube 6. Collar Clamp 7.
WARRANTY Razor Limited Warranty The manufacturer warranties this product to be free of manufacturing defects for a period of 6 months from date of purchase. This Limited Warranty does not cover normal wear and tear, or any damage, failure or loss caused by improper assembly, maintenance, or storage. The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. Razor does not offer an extended warranty.
