Electric Dirt Scooter OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your unit and 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts. Product I.D.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................... 4 Charging the Battery......................................................................................... 5 Pre-Ride Checklist........................................
SAFETY WARNINGS PROPER RIDING ATTIRE Always wear proper protective equipment, such as an approved safety helmet (with chin strap securely buckled), elbow pads and kneepads. A helmet may be legally required by local law or regulation in your area. A long-sleeved shirt, long pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor and drive system. Never ride barefooted or in sandals. Ride defensively.
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Attaching the Handlebars Note: Make sure any cables/wires are out of the way before inserting the stem into the fork. Tool Required: 5 mm Allen wrench WARNING: Failure to properly tighten the collar clamp may allow the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly tightened, the handlebars will not rotate out of alignment with the front wheel under normal circumstances. 1 Loosen the collar clamp.
CHARGING THE BATTERY Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
CONTENTS USAGE Starting the Scooter To start unit, turn on power switch; place both hands on handlebars and use one foot to push scooter forward while applying the throttle with right hand. Stopping the Scooter To stop unit, release the throttle and apply the brake until the unit comes to a complete stop. WARNING: The brake is capable of skidding the rear tire and throwing an unsuspecting rider. Practice in an open area free from obstacles until you are familiar with the brake function.
REPAIR AND MAINTENANCE Chain and Rear Tire Replacement Note: Rear wheel hardware sequence. Tools required: Phillips screwdriver, two (2) 16 mm wrenches. Disassembly Right Side (Throttle) 17-5 - Spacer 17-4 - Washer (plate cut) 17-1 17-2 17-3 17-4 17-5 Frame 17-3 - Washer (thin) 17-2 - Spring Washer 17-1 - Locknut _________________________ Middle 17-6 - Rear Axle Bolt 17-6 1 With a Phillips screwdriver, loosen the two (2) screws on the chain guard and remove.
TROUBLESHOOTING GUIDE *Unit(s) should be turned off and fully charged prior to doing any troubleshooting NOTE: All troubleshooting steps should be performed by an adult only Problem Possible Cause Solution Does not work out of the box Loose connection(s) Check for loose connections/wires. No longer works Loose connection(s) Check for loose connections/wires.
RX200 ELECTRIC SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grip (right/left) 1-1 Handlebar End Cap 1-2 Valve Extender 2. Single Speed Twist Grip Throttle 2-1 Sleeve 3. Handlebar Stem 4. Brake Lever Assembly 5. Collar Clamp 6. Headset (upper/lower) 7. Front Fork 7-1 Limiter and Cover 8.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. RX200_MAN_US_141215.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
