ELECTRIC SCOOTER OWNER’S MANUAL Read and understand this entire manual before using this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts. Product I.D.
HEADLINE CONTENTS Safety Warnings..............................................................................................1-2 Before You Begin................................................................................................3 Assembly and Set-Up..................................................................................... 4-5 Charging the Battery..........................................................................................6 Pre-Ride Checklist............................
HEADLINE SAFETY WARNINGS is not a toy and is intended for use only by persons who are, at a minimum, completely comfortable and competent while operating the product. type of stunts. Racing, stunt riding, or other maneuvers also enhance risk of loss of control, or may cause uncontrolled rider actions or reactions. Razor recommends that children under the age of 16 not be permitted to use this product.
HEADLINE BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents, or kinked cables that may have occurred during shipping. Because the electric scooter was partially assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
HEADLINE AND SET-UP ASSEMBLY Attaching the Front Wheel Tools Required: Two (2) 15 mm Wrenches A B B A C 1 Remove the packing material from the front fork. 2 Remove axle nuts (A) from the 3 Insert the tab on the safety axle bolt (C) and insert the wheel into the front fork. washers into the hole on the front fork and tighten axle nuts using two 15 mm wrenches.
HEADLINE AND SET-UP ASSEMBLY Attaching the Basket Tool Required: 5 mm Allen Wrench D B A WARNING: Do not exceed weight limit of 11 lb (5 kg) on luggage rack. C WARNING: The basket should not be used to carry people or pets. 1 Slide the basket hooks (A) under the bar (B) located on the luggage rack. 2 Align the hole in the basket (C) 3 Insert the washer and bolt into with the hole on the luggage rack (D). the hole in the basket and through the bracket on the luggage rack.
CHARGING THE BATTERY Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
PRE-RIDE CHECKLIST HEADLINE Brake Hardware/Loose Parts Check the brake for proper function. When you squeeze the brake lever, the brake should provide positive braking action. Make sure brake is not rubbing when the lever is released. When you apply the brake with the throttle on/engaged, the brake cut-off switch should cut power to the motor. Before every ride, check all parts, such as nuts, bolts, fasteners, etc., to ensure they are secure and assembled correctly.
HEADLINE USAGE How to Operate Do not activate the twist-grip throttle unless you are on the electric scooter and in a safe, outdoor environment suitable for riding. How to Ride Once you have charged the battery (see page 6 for charging information): 1. Turn power switch “ON”; put kickstand up and place both hands on the handlebars. 2. Place both hands on the handlebars and place one foot on deck plate. Push scooter forward with other foot while applying the throttle with right hand (A).
HEADLINE REPAIR AND MAINTENANCE Turn power switch “OFF” before conducting any maintenance procedures. Adjusting the Brake Tool Required: 10 mm Wrench 1 To adjust the brake cable tension, thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment is attained. Most adjustments are complete at this step. If brake still needs further adjustment, proceed to step 2. WARNING: The brake is capable of skidding the rear tire and throwing an unsuspecting rider.
HEADLINE TROUBLESHOOTING GUIDE *Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting. NOTE: All troubleshooting steps should be performed by an adult only. Problem Possible Cause Solution Scooter does not run Undercharged battery Charge the battery. A new battery should have been charged for at least 12 hours before using the scooter for the first time and up to 12 hours after each subsequent use. Check all connectors.
TROUBLESHOOTING GUIDE HEADLINE Problem Possible Cause Solution Scooter runs sluggishly Driving conditions are too stressful Use only on solid, flat, clean and dry surfaces such as pavement or level ground. Tires are not properly inflated The tires are inflated when shipped, but they invariably will lose some pressure between the point of manufacturing and your purchase. Refer to instructions on page 5 of this manual to properly inflate tires.
ECOSMART METRO PARTS Keep your electric scooter running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grips (x2) 7. Front Fork 12. On/Off Switch 17. Deck Plate 2. Twist-Grip Throttle 8. Limiter Cover 13. Charger Port 18. Brake 3. Handlebar Stem 9. Front Wheel Complete 14. Kickstand 19. Seat 4. Brake Lever Assembly 10. Battery w/ (1) 30 Amp Fuse (3 - 12v/6Ah) 15.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE HEADLINE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
CUSTOMER SERVICE CONTACT INFORMATION Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed below: AMERICAS EUROPE, MIDDLE EAST, AFRICA ASIA Razor USA LLC P.O.
