RSF350® YOUTH ELECTRIC SPORT BIKE OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................4-5 Charging the Battery......................................................................................... 6 Pre-ride Checklist..........................................
SAFETY WARNINGS PROPER RIDING ATTIRE Always wear proper protective equipment, such as an approved safety helmet (with chin strap securely buckled), elbow pads and kneepads. A helmet may be legally required by local law or regulation in your area. A long-sleeved shirt, long pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor and drive system. Never ride barefooted or in sandals.
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the RSF350 is 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Attaching the Handlebars Tool Required: 6 mm Allen Wrench WARNING: Failing to properly adjust and tighten the bolts that affix the handlebars can cause you to lose control and crash. 1 Place the handlebars in the handlebar clamps. 2 Align parallel to the fork and tighten the bolts using a 6 mm Allen wrench. When properly tightened, the handlebars should not move forward or backward.
ASSEMBLY AND SET-UP Inflating the Tires Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and your purchase. Inflate the tires to the correct PSI before first time use. Note: Lower air pressure can result in a shorter ride time. Periodically check both tires. Reinflate when needed. Using a bicycle tire pump equipped for a Schrader valve, inflate both tires to the PSI indicated on the sidewall of the tire.
CHARGING THE BATTERY Your RSF350 may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Make sure the RSF350’s power switch is turned OFF when unit is not in use. If the power switch is left on • Recharge time: up to 12 hours, even if the light turns green. for an extended period of time, the battery may reach a Recommended maximum charging time is 24 hours. stage at which it will no longer hold a charge.
USAGE Starting the RSF350 Stopping the RSF350 Place both hands on the handlebars. Slowly push forward with one foot and apply the throttle. Note: Keep both feet on the foot pegs when unit is in motion. Release the throttle and apply the brake. Note: When coming to a complete stop, place both feet on the ground to balance the unit.
REPAIR AND MAINTENANCE Chain and Rear Wheel Replacement Tools Required: Phillips Screwdriver, 14 mm Wrench, 17 mm Wrench, 5 mm Allen Wrench. WARNING: Failing to properly adjust and tighten the nuts and bolts that affix the front wheel can cause you to lose control and fall. Note the hardware sequence (from outside toward the center). 16-7 1 Loosen the two (2) 5 mm bolts on the brake caliper and remove brake caliper from disc brake.
REPAIR AND MAINTENANCE Front Wheel Replacement Tools Required: 14 mm Wrench, 17 mm Wrench 9-4 9-2 9-2 9-1 9-3 Note: The arrangement of the hardware sequence: 9-4 Locknut 9-3 Washer Front Fork 9-2 Spacer Wheel 9-2 Spacer Front Fork 9-3 Washer 9-1 Axle Bolt 1 Using 14 mm and 17 mm wrench loosen the locknut; slide axle bolt out and remove front wheel.
REPAIR AND MAINTENANCE Battery Care and Disposal Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual. Pb CONTAINS SEALED NON-SPILLABLE LEAD BATTERIES. BATTERIES MUST BE RECYCLED. Pb Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally sound manner.
TROUBLESHOOTING *Unit(s) should be turned off and fully charged prior to doing any Troubleshooting NOTE: All troubleshooting steps should be performed by an adult only Problem Possible Cause Solution Electric motorbike does not run Undercharged battery Charge the battery. A new battery should have been charged for at least 12 hours before using the electric motorbike for the first time and up to 12 hours after each subsequent use. Check all connectors.
RSF350 PARTS Keep your RSF350 running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. 2. 3. 4. 5. 6. Handlebar Grips (Right/Left) Twist Grip Throttle Handlebar Handlebar Clamp (Upper/Lower) Brake Lever Assembly Front Fork 7. Number Plate 8. Front Fender 9. Front Wheel Complete 10. Battery with Fuse 11. Charger Port 12. Battery Cover 2 13. Kickstand 14.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
