Dirt Rocket™ SX350, MX350 and MX400 OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................4-5 Charging the Battery......................................................................................... 6 Pre-ride Checklist..........................................
SAFETY WARNINGS Do not ride your electric product in wet or icy weather and never immerse the product in water, as the electrical and drive components could be damaged by water or create other possibly unsafe conditions. Never risk damaging surfaces, such as carpet or flooring, by use of an electric product indoors. Use only with the recommended charger.
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the electric product is 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Attaching the Handlebars WARNING: Failing to properly adjust and tighten the bolts that affix the handlebars can cause you to lose control and crash. Tool Required: 6 mm Allen Wrench 1 Place the handlebars in the handlebar clamps. 2 Align parallel to the fork and tighten the bolts using a 6 mm Allen wrench. When properly tightened, the handlebars should not move forward or backward. Attaching the Front Fender Note: Front fender design may vary.
ASSEMBLY AND SET-UP Checking Spoke Tension Spoke Flange 19 Hub Flange Spoke Flange Rim Nipple Spoke 20 4 3 2 1 WARNING: Regularly check the spoke tension and retighten the spokes whenever loose. If you have any doubt, ask an experienced motorcycle or bicycle mechanic to inspect your spokes to determine if the spokes need tightening or adjusting. Nipple 1 Verify the spoke tension by grasping and shaking each spoke. Spoke 2 Start with spoke closest to the should not be loose from hub.
CHARGING THE BATTERY Your electric product may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Make sure the electric product’s power switch is turned OFF when unit is not in use. If the power switch is left • Recharge time: up to 12 hours, even if the light turns green. on for an extended period of time, the battery may reach Recommended maximum charging time is 24 hours. a stage at which it will no longer hold a charge.
USAGE Starting the Electric Product Stopping the Electric Product Place both hands on the handlebars. Slowly push forward with one foot and apply the throttle. Note: Keep both feet on the foot pegs when unit is in motion. Release the throttle and apply the brake. Note: When coming to a complete stop, place both feet on the ground to balance the unit.
REPAIR AND MAINTENANCE Chain and Rear Wheel Replacement Tools Required: Phillips Screwdriver, 10 mm Wrench, two (2) 8 mm Wrenches, and two (2) 15 mm Wrenches. SX350 only: Note the hardware sequence (from outside toward the center). 17-2 17-3 17-1 17-2 17-2 1 Using a Phillips screwdriver remove the screws on chain guard and remove. 2 With a 10 mm wrench, loosen Chain Tensioner 4 With two (2) 15 mm wrenches, loosen the axle. Push the chain tensioner down to loosen the chain and remove wheel.
REPAIR AND MAINTENANCE Front Wheel Replacement Tools Required: Phillips Screwdriver and 15 mm Wrench 1 Using a Phillip screwdriver, loosen the two (2) screws on the fork covers (2 per side) and remove covers. 2 Remove the nuts on both sides 3 Remove front wheel and of the front axle using a 15 mm wrench then remove the axle safety washers. install replacement wheel. Re-attach fork covers.
REPAIR AND MAINTENANCE Replacing the Fuse – Cont’d SX350 Model Only 1 Using a Phillips screwdriver, 2 Using a 5 mm Allen wrench and remove the bolt. a 10 mm open wrench to hold the lock nuts, loosen the two (2) bolts underneath the rear of the seat and remove the fairing. Five (5) Phillips screws Two (2) 4 mm Hex bolts 3 On the opposite side of the charger port, locate and remove the five (5) Phillips screws and (2) 4 mm Hex screws or bolts using a 4 mm Allen wrench. Separate and remove cover.
REPAIR AND MAINTENANCE Battery Care and Disposal Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual. Pb CONTAINS SEALED NON-SPILLABLE LEAD BATTERIES. BATTERIES MUST BE RECYCLED. Pb Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally sound manner.
TROUBLESHOOTING GUIDE *Unit(s) should be turned off and fully charged prior to doing any Troubleshooting NOTE: All troubleshooting steps should be performed by an adult only Problem Possible Cause Solution Electric product does not run Undercharged battery Charge the battery. A new battery should have been charged for at least 12 hours before using the electric product for the first time and up to 12 hours after each subsequent use. Check all connectors.
SX350 PARTS Keep your SX350 running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grip (Right/Left) 2. Single-Speed Twist-Grip Throttle 2-1. Sleeve 3. Handlebar 4. Number Plate 5. Brake Lever Assembly 6. Handlebar Clamp (Upper/Lower) 7. Front Fender 8. Fork Cover (Right/Left) 9. 10. 11. 12. 13. 14. 15. 16.
MX350/MX400 PARTS Keep your MX350/MX400 running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grip (Right/Left) 2. Single-Speed Twist-Grip Throttle 2-1. Sleeve 3. Handlebar 4. Brake Lever Assembly 5. Handlebar Clamp (Upper/Lower) 6. Front Wheel Complete 7. Front Fork 1 8. 9. 10. 11. 12. 13. 14.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
