PowerRider™ 360 OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts. Product I.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................4-6 Charging Battery/Pre-ride Checklist................................................................. 7 Usage................................................................
SAFETY WARNINGS PROPER RIDING ATTIRE Use only with the recommended charger. Riders should always wear a properly fitted helmet that complies with U.S. Consumer Safety Commission (CPSC) Standard 16 CFR 1203. A helmet may be legally required by local law or regulation in your area. A long-sleeved shirt, long pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor and drive system.
BEFORE YOU BEGIN Remove contents from box and check parts against parts diagram found on page 13. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint or dents that may have occurred during shipping. Because the PowerRider™ 360˚ was partially assembled and packed at the factory there should not be any problems, even if the box has a few scars or dents.
ASSEMBLY AND SET-UP Attaching the Frame Required Tools: Two (2) 5 mm Allen wrenches 1 Using two (2) 5 mm Allen 2 Remove and discard the plastic 4 Securely tighten the (longer) 5 Securely tighten the (shorter) wrenches, remove the coupling bolt on the end of the frame and the coupling bolt in the middle of the frame. coupling bolt on the rear frame using two (2) 5 mm Allen wrenches. 3 Insert the rear frame into the insert. Note: The coupling bolt in the middle of the frame is shorter.
ASSEMBLY AND SET-UP Attaching the Seat Required Tools: Two (2) 5 mm Allen wrenches 1 Using two (2) 5 mm Allen wrenches, remove the four (4) coupling bolts from the rear frame. 2 Align the four (4) holes in seat 3 Tighten the coupling bolts using with the four (4) holes in frame. Insert the coupling bolts through the top and bottom of the frame. two (2) 5 mm Allen wrenches.
ASSEMBLY AND SET-UP Attaching the Flag 1 2 Insert flag into fixed hole located on the rear of the frame. Unfolding the Foot Pegs WARNING: When riding, foot pegs must be unfolded and both feet placed securely on pegs. 1 Unfold the foot pegs. Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D.
CHARGING THE BATTERY Your PowerRider 360 may not have a fully charged battery; therefore it is a good idea to charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
USAGE Starting the PowerRider 360 Stopping the PowerRider 360 To start the unit, turn the power switch “ON”. Place both hands on the handlebars and press the push button throttle. Note: Keep both feet on the foot pegs when unit is in motion. To stop the unit, release the push button throttle and apply the brake until the unit comes to a complete stop.
REPAIR AND MAINTENANCE Reassembly Nut Brake Housing Anchor Front Fork Washer Bolt Note: Front wheel hardware sequence 11-7 11-6 11-5 11-4 11-2 Brake Plate 1 Install the chain onto the front wheel sprocket. Slip the wheel axle into the fork slot and through the wheel (note the sequence of the hardware pictured to the right). Push the chain tensioner down to create slack in the chain. Hand tightened the front axle locknuts.
REPAIR AND MAINTENANCE Adjusting the Brake Required Tools: Phillips screwdriver, 10 mm wrench 1 To adjust the brake cable 2 Using a Phillips screwdriver, 4 If the brake is too tight or too 5 Replace the motor cover/ tension, thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment is attained. Most adjustments are complete at this step. If the brake still needs further adjustment, proceed to the following steps.
REPAIR AND MAINTENANCE Battery Care and Disposal Never store the product in freezing or below freezing temperatures! Freezing will permanently damage the battery. Failure to recharge the battery at least once a month may result in a battery that will no longer accept a charge. Pb CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED. Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally safe manner.
TROUBLESHOOTING GUIDE *Unit(s) should be turned off and fully charged prior to doing any Troubleshooting NOTE: All troubleshooting steps should be performed by an adult only Problem Possible Cause Solution Product does not run. Undercharged battery. Charge the battery. A new battery should have been charged for at least 12 hours before using the product for the first time and up to 12 hours after each subsequent use. Check all connectors.
POWERRIDER 360 PARTS Keep your PowerRider 360 running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar Grips (right/left) 8. Control Module 16. Rear Wheel Complete (x2) 1-1 Handlebar Cap 9. Motor (12V/100W) 16-1 Rear Wheel Caster Cover (Upper/Lower) 1-2 Valve Extender 10. Brake Lever Assembly 16-2 Spring Washer 2.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
