LIL’ E™ ELECTRIC SCOOTER OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice. Please have your product along with the 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................... 4 Charging the battery......................................................................................... 5 Pre-Ride Checklist........................................
SAFETY WARNINGS ACCEPTABLE RIDING PRACTICES AND CONDITIONS Direct parental supervision is required at all times. Electric products are meant to be used only in controlled environments, free of potential traffic hazards and not on public streets. Do not allow your child to ride an electric product in any areas where vehicle traffic is present. Never use near steps, sloped driveways, hills, roadways, alleys or swimming pool areas.
BEFORE YOU BEGIN Adult assembly required. Remove contents from box. Inspect the contents for scratches in the paint and/or dents that may have occurred during shipping. Because your electric product was partially assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Turn power switch OFF before conducting any maintenance procedures. Attaching the Front Wheel/Handlebars Tool Required: 5 mm Allen wrench Note: Failure to secure the handlebars can cause the handlebars to come out while riding. 1 Remove and discard plastic cap 2 Loosen the 5 mm bolt on the collar clamp. WARNING: Failure to properly tighten the collar clamp may cause the rider to lose control and fall.
CHARGING THE BATTERY Your Lil’ E may not have a fully charged battery; therefore it is a good idea to charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
PRE-RIDE CHECKLIST Safety Gear Frame and Handlebars Always wear proper protective gear, such as an approved safety helmet. Elbow pads and kneepads are recommended. Always wear closed toe shoes (lace-up with rubber soles) and keep shoelaces tied and out of the way of the wheels. NEVER RIDE BAREFOOTED OR IN SANDALS. Check for cracks or broken connections. Although broken frames are rare, it is possible for an aggressive rider to run into a curb or object and wreck and bend or break.
REPAIR AND MAINTENANCE Battery Care and Disposal Do not store in freezing or below freezing temperatures! To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 5 of this owner’s manual. Pb CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED. Pb Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally safe manner.
PRODUCT PARTS Keep your Lil’ E running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebars/T-bar 1-1 Push Button Throttle 2. Handlebar Grips (X2) 3. End Cap (X2) 4. Downtube Cover 5. Collar Clamp 6. Front Fork w/Limiter 7. Front Wheel 8. 9. 10. 11. Battery Strap Battery Cover Battery Circuit Board 11-1 Power Switch 11-2 Charger Port 12. Motor 13.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
CUSTOMER SERVICE CONTACT INFORMATION Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed below: AMERICAS EUROPE ASIA Razor USA LLC P.O.