001RB Series Owners Manual 1001RB 1001RB/210 1001RB/115
Table of Contents 1001RB Series Table Of Contents Introduction.....................................................................3 Quick Start.......................................................................5 Sound Tips....................................................................... 6 Bi-Amp and Normal Operation.................................... 7 Safety Information.......................................................... 8 Installation and Maintenance....................................
1001RB Series Congratulations Gallien-Kruger, Inc. 2240 Paragon Drive San Jose, CA 95131 phone: (408) 441-7970 fax: (408) 441-8085 Internet: www.gallien-krueger.com Email: sales@gallien.com To get the most out of your new purchase please take a few minutes to read through this manual. If you are in a hurry, we suggest you at least read through the Quick Start section before setting up your new rig.
1001RB Series Introduction Always Listening I have never seen the point in doing things the way others have done them. I also have not been very interested in following the latest fad. I am a Stanford educated engineer who worked his way through school as a musician. Like all musicians, I have lugged amplifiers up stairways and into car trunks, always wondering why these things had to be so heavy, bulky, and hard to handle.
1001RB Series Quick Start Caution: First: Set the power switch to Off and connect the supplied power cable, from the amplifier AC receptacle, to an AC power outlet of proper voltage and power rating (see safety information on page 7 for details). Do not connect the Speakon cable labeled “Bridge Mode” to the 1001RB. This may result in damage to the amplifier. Next: Connect your speaker cabinets to the amplifier outputs marked 540W AMP ONLY or “SPEAKON” OUTPUTS.
1001RB Series Sound Tips Sound Tips The1001RB Series has several unique features which, if used properly, will obtain that sound you have been searching for. The Equalizer: Boost/Master: The Equalizer is used to fine tune your sound. When adjusting it, do it just a little at a time. These are active circuits, and small changes can make a big difference in your sound.
1001RB Series Bi-Amp & Normal Operation Bi-Amp and Normal Operation The 1001RB’s unique design makes setup for Bi-Amp or normal configuations simple. The operational mode is configured by how you connect your speaker cabinets. In addition, you have the option of driving one cabinet in BiAmp and one in Normal operation.
1001RB Series Safety Information Safety Information Do Not Use Extension Cords: Verify Line, Voltage and Amperage Before Use: To avoid safety hazards, use only the power cord supplied with your unit. If a replacement cord is used, make certain that it is of consistent quality and gauge as the original. We do not recommend using extension cords with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them.
1001RB Series . Installation: Cleaning: · When the unit gets dirty, wipe it with a clean, soft and dry cloth. If necessary, first wipe the surface with a soft cloth slightly dampened with mild, soapy water, followed by a fresh cloth with clean water. Wipe immediately with a dry cloth. Never use benzene, thinner, alcohol, or other volatile cleaning agents. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticides near the unit. . · . ..
01RB Series Front Panel Controls 1 2 3 4 5 6 7 9 8 10 11 12 13 14 15 16 17 18 19 Front Panel Controls 1-Balanced Direct Out: 9-High Mid: An electronically balanced output, that you can run to your P.A. system. 2-Pre/Post EQ Button: Boost and cut at 1 kHz +10dB, “Q Optimized,” band pass type. Works on lower string harmonics, and effects the punch of your sound. Selects the direct out signal from before or after the EQ.
1001RB Series 3 Rear Panel Controls CAUTION: 1- AC Receptacle: UNDER NO CIRCUMSTANCES SHOULD THE 540W AMP AND THE 50W AMP BE CONNECTED TOGETHER OR BE CONNECTED TO THE SAME SPEAKER !!! The power cord is detachable and plugs in here. 2- 540W Amp Only: 540W power amp output for Full-Range operation only. They deliver 540 watts into 4 Ohms. Lower impedances should not be used. Each jack has a minimum of 8 Ohms each. Higher impedances such as 8 Ohms, 16 Ohms, or No Load are acceptable.
1001RB Series 1001RB Series Combos 1001RB Series Combos The 1001RB Series combos deliver the1001RB’s unique features and distinct sound by using a variety of internal speaker configurations, GK’s RBH cabinet technology and a unique Lock N’ Roll transport system. Speaker Configurations: Lock N Roll Transport System: 1001RB/115 The Lock N’ Roll transport system is designed for quick and easy rolling of the combo on flat surfaces such as carpet, flooring, pavement, etc.
1001RB Series Tech Talk Characteristics of the 1001RB: There is nothing in the 1001RB Series power amp to come between you and your sound except faithful, raw power. Bi-Amp Sound: . . .. . . .. Bass players have always liked the growl they get from slight overdrive. In GK amps this comes partly from the boost circuits and partly from the power amp. The problem is that growl, sounds great through woofers, and horrible through horns.
1001RB Series Tech Talk Tech Talk Electronic Crossover: Voicing Filters: Bi-Amp systems allow the crossover to be electronic and therefore, have much higher quality than passive crossovers. A crossover separates the sound into two parts (high and low frequency). The highs are sent to the horn or high frequency cabinet and the lows are sent to the woofer. In an ideal system, adding the highs and the lows back together would recover the original signal.
1001RB Series Tech Talk Speakon Cables: The 1001RB Series uses a “dual rail power supply” that generates about half the heat of conventional amplifiers. Low output signals run off a low voltage supply, and high level signals run off a high voltage supply. This keeps the amp running a lot cooler and makes it much more reliable. To cool the amp when its being driven hard, we’ve designed a temperature sensitive fan cooling system.
1001RB Series Specifications Block Diagram 1001RB Series Specifications: Output Power: 540W Amplifier 50W Amplifier Input Section: Maximum Input Level With -10dB pad Input Impedance Send output impedance Return input impedance Tuner Output Impedance Direct Output Impedance Equalizer: Bass Lo-Mid Hi-Mid Treble Voicing Filters: String Bass Button Contour Presence Crossover Noise Cooling 540W @ 8 Ohms 540W @ 4 Ohms 50W @ 8 Ohms 50W @ 4 Ohms Continuously VariableSpeed Fan Amplifier Protection: Full short