T SERIES OWNERS MANUAL
C O N T E N T S INTRODUCTION 1 BREAK IN PERIOD 1 F E A T U R E S 2 SETUP SUGGESTIONS 3, 4, 5 CLAMPING BRACKET 6 TROUBLESHOOTING 7 CARE & CLEANING 7 S P E C I F I C AT I O N S 8 W A R R A N T Y 9
INTRODUCTION ongratulations on your purchase of an RBH loudspeaker system! Your speakers are the result of many years of research and development dedicated to producing high quality products for home audio and audio/video systems. This manual contains features, setup recommendations and specifications for RBH T Series High Performance loudspeaker systems. We recommend that you thoroughly read through the material contained in this manual before connecting your loudspeakers.
F E A T U R E S t the heart of our T Series loudspeaker system is a proprietary aluminum cone bass/midrange driver (speaker). The unique aluminum cone material combines stiffness, low mass, and self damping properties in a manner that allows virtually uncolored presentation of program material. A powerful magnet, extended voice coil and bumped back plate give the bass/midrange driver high excursion capability, which ensures accurate dynamic reproduction.
SETUP SUGGESTIONS he T Series is a modular speaker system designed to be used individually or with the RBH 1010-SEN subwoofer. This combination with the subwoofer provides for full range reproduction of the program material. There are three basic models or configurations within the T Series: The T-1: The T-1 is the main speaker section that reproduces the high and midrange frequencies.
SETUP SUGGESTIONS CONTINUED t is imperative that the T-1 cabinet’s are positioned so that the tweeters face toward the center of the listening position. If the tweeters are not placed properly, there will be a great reduction in imaging, soundstaging and overall performance of the speaker system. Proper setup is shown below. In home theater applications, the CENTER channel speaker should be placed in the center between both left and right main speakers.
SETUP SUGGESTIONS CONTINUED URROUND* speakers may be placed either behind or to the sides of the listening position. The listening position should be at the center of both surround speakers. For best performance you may want to experiment with angling the surround speakers either towards or away from the listening position. All RBH Signature Series and Signature Inwall loudspeakers are sonically matched with the T Series for seamless integration in a home theater setting.
CLAMPING BRACKET he clamping bracket, provided with the T-2 and T-3 system, consists of 2 end pieces, 2 hex head bolts and 1 round rod, all pieces are machined from solid aluminum. To install, attach an end piece to each end of the rod with the screws and place in between the two cabinets from side to side (not front to back). Two of these are required in between each speaker. As the bolts are tightened, pressure will be created holding the top and bottom sections firmly together.
TROUBLESHOOTING Situation: Probable Cause: Solutions: Speaker wire not connected. Make sure wire is properly connected at both the speaker and the amplifier observing proper polarity. Speaker selector on amplifier is not on. Activate proper speaker selector on amplifier. Balance control on receiver or preamp is not centered. Place balance control in the center. Speaker wire not completely connected. Check all connections at amplifier and speakers. Only the woofer or midrange/ tweeter are playing.
T-1 EN C EQ U 3) 1” SILK DOME TWEETERS 4) 61⁄2” ALUMINUM CONE MIDWOOFERS 1010-SEN 20HZ-100HZ ± 3DB 91 DB 2.83V/1M 200-400 WATTS 2) 10” ALUMINUM COME SUBWOOFERS T-2N T-2P 20HZ-20KHZ ± 3DB 91DB 2.83V/1M 100-500 WATTS 3) 1” SILK DOME TWEETERS 4) 6 1⁄2” ALUMINUM CONE MIDWOOFERS 2) 10” ALUMINUM CONE SUBWOOFERS T-3N T-3P 20HZ-20KHZ ± 3DB 91DB 2.
W A R R A N T Y our RBH Sound T Series loudspeaker is covered by a limited warranty against defects in materials and workmanship for a period of 5 years from the original date of purchase. This warranty is provided by the authorized RBH Sound dealer where the loudspeaker was purchased. Warranty repair will be performed only when your purchase receipt is presented as proof of ownership and date of purchase.
It is the policy of RBH Sound to continuously incorporate improvements into products. All specifications are subject to change without notice. RBH Sound, Inc. 976 N. Marshall Way • Bldg. 2, #4 • Layton, Utah • USA • 84041 (800) 543-2205 • (801) 543-2200 • FAX (801) 543.3300 • www.rbhsound.com Copyright © 2003, RBH Sound, Inc. All Rights Reserved.
REDEFINING THE WAY YOU EXPERIENCE SOUND