020 mm 1030 mm 550g Li-pol 3-4s V2.
1. 2. min. 1h Cut 3. Top side 4. 2x Carbon 3x0,5x1000 mm Medium CA 1 2 3 5 4 6 7 1 1 2 Bottom side 2x Carbon 3x0,5x1000 mm 5. 630mm 166mm 3 4 137mm 115mm 5 6 100mm 7 86mm 90mm 6. NO CA !!! Medium CA 1 2 3 5 4 6 7 1 1 2 570mm 166mm 3 4 137mm 115mm 5 6 100mm 7 86mm 90mm 7. 8. Medium CA 9. Cut Top + Bottom side 10.
11. 12. Push Cut 1. Top side 13. 2. Bottom side 14. Carbon 3x1x1000 Carbon 3x1x1000 Thin CA NO CA Top side 15. L+R 16. Thin CA Kevlar 100mm 1/2 1/2 Thin CA Cut 17. 18. Aileron Cut 19. Push L+R 20.
21. 22. L+R Servo center Aileron servo 23. L+R 24. 25. L+R 26. 27. Cut 2x 13 mm 13 mm L+R L+R 28. 13 mm L+R 29. 30.
L+R 31. 32. cca 23,6° For servo cable 90° Cut Šablona k vytisknutí na straně 14. Template to print on page 14. 4 mm 33. Hot glue 35. 37. 39. L+R L+R 34. L+R 36. L+R 38. L+R 40.
Bottom side 41. Bottom side 42. nebo Medium CA or 43. 44. Sand paper Carbon 4/3 x 330 45. 46. NO CA !!! NO CA !!! 47. 48. L+R Medium CA 49. 50.
51. 52. opatrně-carefully!!! 0,5-1mm mezera Activator Elevator servo center 53. 55. 0,5-1mm gap Medium CA 54. 56. Hot glue Cut 57. 58. Medium CA Top side 59. 60.
61. Cut 62. Sand paper Medium CA 63. Push 64. Medium CA Drill 65. 3mm 66. 3 x 25 mm 67. 68. Cut Sand paper 69. Drill 3mm 70.
71. 72. Screw M3 x 16 Nut M3 Washer 3 L+R 73. L+R 74. Medium CA Activator 75. 76. L+R Medium CA 77. L+R Cut 78. L+R Medium CA 79. 80.
82. 81. opatrně-carefully!!! 90 83. 84. Carbon 1,8 x 140 mm 86. 87. 88. Cut 89. 90. Activator Medium CA Sand paper Thin CA 85. 1. 2.
91. 92. Medium CA Servo center 93. Rudder servo Medium CA 94. Medium CA 95. Push Push 96. Medium CA 97. 98. Push Medium CA 99. Cut 100.
101. Thin CA 102. Medium CA Push 103. 104. Push Carbon 1 x 500 105. 106. Thin CA Push 107. 108. Left L+R 109. 1. 2. Medium CA Activator 110.
111. 112. Activator Medium CA L+R L+R CG 265 - 275 mm Batt RC We wish you many happy flying hours with the Edge 540 V3 Your RC Factory team.
23,6° cm 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
