080 mm 1120 mm 850g Li-pol 3-4s 2814-20 100g / 300w 9-10” V1.
0 10 cut line cut line 20 30 40 50 60 70 80 90 100 110 120 130 32mm 140 m 55,5m m 150 32mm 55,5m 160 170 180 190 200 210 220 230 240 250 260 270 280 cut line cut line
0 10 cut line 20 30 cut line 40 50 60 70 80 90 100 110 120 130 140 119mm 154mm 92mm 127,5mm 150 160 170 180 190 200 210 220 230 240 250 260 cut line 270 280 cut line
1. Top Side - TS 2. Medium CA No Glue Bottom Side - BS 3. TS 4. TS TS Medium CA 5. 6. cut cut cut 6mm Z obou stran / from both sides 7. 8. Medium CA Thin CA carbon 5x1x1000 1. carbon 5x1x1000 2. BS TS 9. 10. D1 D3 D2 P D4 Medium CA Thin CA D5 4x carbon 3x0.5x1000: 2x P 2x P D2 D3 carbon 3x0.
11. 1. 12. Medium CA 2. Carbon 3. Thin CA Z obou stran / from both sides 13. 14. Thin CA + Z obou stran / from both sides Medium CA TS + + + + + Z obou stran / from both sides 15. 16. 17. 18. No Glue Carbon 5/3x330mm a. 58. No Glue No Glue Medium CA 19. 20. a. BS b.
21. Gap 0.5-1mm Gap 0.5-1mm 22. Medium CA L R 23. Z obou stran / from both sides Medium CA 24. 1pcs carbon 3x1x1000 cut into 4pcs a 210mm 25. Medium CA 26. front side Medium CA + 27. Thin CA Medium CA Sand paper 28. + Carbon 3x1x210 Z obou stran / from both sides 29. Medium CA 30.
31. 32. Servo center L+R 1.5mm Print + cut of the 2+3nd page of the manual 33. 34. Cut Cut Cut Cut L+R 35. 36. No Glue Thin CA L+R 37. L+R L+R 38. Drill 1.5mm 39. L+R 40.
51. Medium CA 52. L+R 53. L+R 54. 32mm 32mm 55. cut 56. 55.5mm 57. 58. b. 59. 60. 4pcs M3x30 4pcs washer 3 18.
41. 42. L+R 43. 44. Medium CA 45. 47. 46. M3x16 48. Washer 3 Nut M3 49. 50.
61. Medium CA 62. Medium CA 63. 64. Washer 3 65. 66. 67. 68. 69. 70.
71. 72. Drill 73. 74. Thin CA 1.5mm Sand paper Carbon 1.8x100mm 75. 76. 127,5mm Thin CA 77. 79. 78. Medium CA 80. Carbon 1.
81. 82. 154mm Thin CA Thin CA, drill 1.5mm, screw... Medium CA 83. 84. Medium CA 86. Medium CA 87. 88. Drill 5 2x Drill 2mm M 2x M 10 85. 89. 90. 1.
91. 92. M2x5 93. Medium CA Activator 94. Medium CA 95. 96. Medium CA 98. 97.
