Instructions for Use
16
CYCLE CHARGE/DÉCHARGE OU DÉCHARGE/CHARGE POUR ACCUS NICD/NIMH
Choisissez l’ordre de la séquence selon l’état actuel de l’accu. Si l’accu
est complètement chargé, utilisez l’ordre Décharge/Charge. Si l’accu doit
être chargé, utilisez Charge/Décharge.
Appuyez sur START/ENTER pour conrmer le choix, puis choisissez le
nombre de cycles pour l’accu entre 1 et 5.
Appuyez et maintenez START/ENTER pour lancer le processus.
Pour arrêter le processus, appuyez sur Batt Type/Stop une fois. Changez
le courant de charge ou de décharge en appuyant sur START/ENETR
durant la charge. Un son indique quand le processus est terminé.
Quand le processus est terminé, utilisez les boutons INC/DEC pour voir
les capacités chargées et déchargées. En appuyant à nouveau sur INC ou
DEC, les résultats des cycles suivants s’afchent.
Réglez le courant de charge à gauche et la tension nominale à droite.
La plage de courant de charge est de 0,1 à 6,0 A et la tension doit
correspondre avec l’accu à charger.
Lancez la charge en appuyant sur Start/Enter plus de 3 secondes.
L’écran afche l’état du processus de charge. Pour arrêter la charge en
cours de route, appuyez une fois sur Batt Type/Stop. Un son indique la
n du processus.
Le taux de charge optimal pour un accu plomb-acide est de 1/10 de la capacité. Les accus au plomb ne
doivent pas être chargés rapidement. Suivez toujours les instructions fournies par le fabricant de l’accu.
Quand vous êtes sûr de connaître les bons réglages pour votre accu au plomb, appuyez sur START/ENTER
pour entrer les paramètres. Utilisez les boutons INC/DEC pour ajuster les valeurs et appuyez sur START/
ENTER pour enregistrer les valeurs sélectionnées.
PROGRAMME POUR ACCUS PLOMB-ACIDE
CHARGE D’UN ACCU AU PLOMB
Select the sequence based on the current state of the battery.
If the battery is fully charged, use the Discharge/Charge
sequence. If the battery needs to be charged, use Charge/
Discharge. Press START/ENTER to confirm the setting, then
choose how many times to cycle the battery (1-5). Press and
hold START/ENTER to begin the process.
To stop the process, press the Batt/Stop button once. Change
the discharge or charge current by pressing START/ENTER
while charging. An audible sound will indicate when the process
has ended.
When the process is completed, use the increase/decrease
buttons to see the amount of capacity that was charged/
discharged. By pressing increase/decrease again, the results of
the next charge cycle will be shown.
Set up the charge current on the left and the nominal voltage of
the battery on the right. The charge current ranges from 0.1A to
6.0A and the voltage should be matched with the battery being
charged. Start the charge process by pressing the START/
ENTER button for more than 3 seconds.
The screen will display the current state of charging. To stop the
process, press the Batt type/Stop key once. An audible sound
will indicate you have ended of process.
This program is for charging Pb (lead-sulfuric acid) batteries with a nominal voltage from 2V
to 20V.The optimal charge rate for a Pb battery is 1/10 of the capacity. Pb batteries must NOT
be charged rapidly. Always follow the instructions supplied by the battery manufacturer.
When confident you have the correct settings for your Pb battery, press START/ENTER to
begin editing the settings. Use the increase/decrease buttons to adjust the value and press
START/ENTER to save the selected value.