Instructions for Use

13
PROGRAMME POUR ACCUS AU LITHIUM (LILO/LIPO/LIFE)
CHARGE D’ACCU AU LITHIUM
Ce paramètre règle la capacité maximale à charger dans l’accu durant
une charge. Si le delta-peak n’est pas détecté et que la minuterie de
sécurité n’a pas fonctionné pour n’importe quelle raison, cette fonction
coupe automatiquement le processus à la valeur de capacité sélec
-
tionnée.
Les bips à chaque appui de bouton conrment les actions. Les bips ou
mélodies surviennent à divers moments du processus pour indiquer les
changements de mode. Ces sons peuvent être activés ou désactivé.
Ce programme surveille la tension de la batterie d’alimentation. Si la
tension tombe sous une valeur que vous avez réglée, le processus est
interrompu pour protéger la batterie d’alimentation.
-
9
-
L
6. Lithium battery(Lilo/LiPo/LiFe)program
These programs are only suitable for charging and discharging Lithium batteries
with a nominal voltage of 3.3V, 3.6V and 3.7V per cell. These batteries need to
adopt different charge technique is termed a constant voltage(CV) and constant
current(CC) method. The charge current varies according to the battery capacity and
performance. The final voltage of charge process is also very important; it should be
precisely matched with the charade voltage of the battery. They are 4.2V for LiPo, 4.1V
for Lilo, and 3.6 V for LiFe. The charge current and nominal voltage as for cell count
set on the charge program must always be correct for the battery to be charged.
When you are willing to alter the parameter value in the program, press Start/
Enter key to make it blink then change the value with INC or DEC key. The value will
be stored by pressing Start/Enter key once.
6.1 Charging Lithium Battery
The left side of the first line shows the type of battery
you select at the users setting. The value on the left
side of second line sets a charge current and the value
on the right side of second line sets the voltage of the
battery pack.
After setting the current and voltage press Start/Enter
key for more than 3 seconds to start the process.
(Charge current:0.1~7.0A,Voltage:1~6 series)
-
9
-
L
6. Lithium battery(Lilo/LiPo/LiFe)program
These programs are only suitable for charging and discharging Lithium batteries
with a nominal voltage of 3.3V, 3.6V and 3.7V per cell. These batteries need to
adopt different charge technique is termed a constant voltage(CV) and constant
current(CC) method. The charge current varies according to the battery capacity and
performance. The final voltage of charge process is also very important; it should be
precisely matched with the charade voltage of the battery. They are 4.2V for LiPo, 4.1V
for Lilo, and 3.6 V for LiFe. The charge current and nominal voltage as for cell count
set on the charge program must always be correct for the battery to be charged.
When you are willing to alter the parameter value in the program, press Start/
Enter key to make it blink then change the value with INC or DEC key. The value will
be stored by pressing Start/Enter key once.
6.1 Charging Lithium Battery
The left side of the first line shows the type of battery
you select at the users setting. The value on the left
side of second line sets a charge current and the value
on the right side of second line sets the voltage of the
battery pack.
After setting the current and voltage press Start/Enter
key for more than 3 seconds to start the process.
(Charge current:0.1~7.0A,Voltage:1~6 series)
Ces programmes ne sont adaptés que pour charger et décharger des accus au lithium d’une tension nominale
de 3,3 V, 3,6 V et 3,7 V par élément. Ces accus doivent utiliser une technique de charge qui est appelée la
méthode CC/CV (Courant constant puis Tension constante). Le courant de charge varie en fonction de la
capacité de l’accu et de ses performances. La tension de n de charge est également très importante. Elle doit
correspondre précisément avec la tension de charge de l’accu. Cette tension est de 4,2 V pour les LiPo, 4,1 V
pour les LiIo et 3,6 V pour les LiFE. Le courant de charge et la tension nominale ainsi que le nombre d’éléments
réglés dans le programme de charge doivent toujours être corrects pour l’accu à charger.
Quand vous voulez modier la valeur des paramètres dans le programme, appuyez sur la touche Start/Enter
pour faire clignoter la valeur, puis modiez cette valeur avec les touches INC ou DEC. La valeur est enregis
-
trée en appuyant une fois sur la touche Start/Enter.
La partie gauche de la première ligne montre le type d’accu choisi. La valeur à
gauche de la seconde ligne est le courant réglé par l’utilisateur. Après réglage
du courant et de la tension, appuyez sur le bouton Start/Enter plus de 3
secondes pour lancer le processus.
(Courant de charge : 0,1 à 7,0 A, Tension : 1 à 6 S)