Recommended Tools Hex Drivers (1.5mm, 2mm, 2.5mm) Thread Lock Cross Wrench Long Nose Pliers Tips for Assembly Use good quality hex drivers to avoid stripping screw heads. Use thread lock when putting metal screws into metal parts. Note: Steps marked with an asterisk (*) require thread lock. Use thread lock sparingly. Do not over tighten screws otherwise you may strip the thread.
All RC4WD products are warranted to be free of defects in materials and workmanship when new. Our limited warranty does not cover damages due to normal wear and tear, user error of assembly or installation, user modifications, user's failure to perform routine maintenance, addition of aftermarket parts or option parts. This warranty lasts as long as the original purchaser owns the product.
Trail Finder 2 TF2 RTR Electronic manual This is a step by step overview of your new TF2 RTR electrical items and how they connect. 1. ESC with BEC (Z-E0007) 2.
3. This connects the BEC of the ESC to the radio’s receiver (Z-R0008). This connects to the B/C port. 4. Connecting the BEC to the radio’s receiver Channel (B/C). Connecting the ESC to the radio’s receiver Channel 2 (CH2). Channel 2 is the throttle control of the radio.
5. Connect the servo (Z-E0035) to the radio’s receiver Channel 1 (CH1). This controls the trucks steering from the radio. 6. Show the battery connected to the ESC. 4-9 NiCd/NiMH cells (1.2V per cell) or 3S 11.1V LiPo.
. This final step shows all the items as they are connected on the truck.
Item shown: Z-R0009 XR3 3-Channel 2.4Ghz Transmitter/Receiver Radio Z-E0007 Outcry Crawler Speed Controller ESC with TurboBEC Z-E0035 Twister High Torque Metal Gear Digital Servo Z-E0004 540 Crawler Brushed Motor 45T Optional Parts: Z-R0008 XR3 2.4Ghz 4-Channel XR4 2.
This is an instruction sheet for the Outcry ESC (Electronic Speed Control). This will cover basic questions about the ESC and how it works. If you have further questions about the ESC, Please contact our support line or use our forum. Details are shown on page 1 of this manual. The Outcry ESC has built in non-adjustable drag break. The ESC comes with a BEC (battery eliminator circuit). This allows you to get full power to the other electronics in your setup. This ESC is a simple Plug and Play unit.
T C ix
G x
All of the hardware should be taken from Bag C ●1* M3 x 6mm Steps 2 to 5 should be done on both frame rails Metal parts can be found in parts Bag A ●2* M3 x 8mm 1
Plastic parts can be found in parts Bag D ●3 M3 x 14mm The holes in the slider can be rather small. In some cases its good to use an alignment tool to align the sliders with the chassis holes before installation.
●6* M3 x 10mm M3 x 16mm ●7* M3 x 8mm 3
●8* M3 x 12mm ●9* M3 x 8mm 4
●10* M3 x 10mm ●11* Step Screw 5
●12* ●13 6
●14* ●15* 7
●16 ●17 8
●18-1 1 Gift 2 Step 18-2 3 Step 24 ●18-2 9
●19* 10
●20-1 ●20-2 11
Attach leaf springs to front and rear axles Note: The smaller helper leafs can be fitted below the main leaf to stiffen the suspension ●21 Remove the screws first ●22 12
●23 ●24 13
●25-1 80mm Shock ●25-2 14
●26* ●27* 15
●28-1* ●28-2* 16
●29* ●30 CORRECT ALIGNMENT INCORRECT ALIGNMENT Please check alignment when installing your drive shafts.
●31 ●32 18
●33-1 ●33-2* 19
●34-1 ●34-2 20
●35 ●36 21
●37 Wheel disassembly shown 1. Insert internal beadlock ring into tire 2. Install wheel front and back. Careful of the wheels alignment to get the look. 3. Use the included longer hardware to help aid in tire and wheel installation. Be sure to slowly tighten the nuts on the longer hardware until you are able to begin installing the included shorter hardware. 4. Install the correct shorter length hardware into the remaining holes.
5. Begin to tighten the hardware in a star shape pattern to fully seat the tire to the wheel properly. 7. Now you can remove the longer hardware. 6. Your wheel and tire should be fully seated like shown. 8. Install the correct shorter hardware. 9. Completed assembly of your new wheels & tires.
●38 Note: Body will need to be assembled prior to fitting. See Mojave ll body assembly instructions.
Drive it like you built it! 25
Spare Parts Z-S0591 TF2 Hardware Bag C Z-B0029 TF2 Plastic Body Posts Z-S0592 TF2 Fuel Cell Radio Box Z-S0593 TF2 Bumper Mounts Z-S0594 TF2 Front Tube Bumper Z-S0595 TF2 Rear Tube Bumper Z-S0596 TF2 Side Sliders Z-S0597 TF2 Shock Hoops Z-S0598 TF2 Tcase Mounts Z-C0018 TF2 Chassis Set Z-U0024 TF2 Scale Transfer Case Z-U0028 R3 Scale Single Speed Transmission Z-S0898 TF2 Long Drive Shaft Coupling For R3 SingleI Speed Z-S0600 TF2 2mm Spacers Z-S0601 TF2 Yota Steering Links Z-S0443 Aluminum Driveshaft Locking R
Optional Parts Z-S0603 TF2 Rear 4 Link Kit Z-S0342 XVD for Yota Axle Z-S0068 U-Bolt kit for Yota Axles Z-S0196 Yota Locking Hub Nuts Z-S0194 Front Locking Hub Nuts Z-S0175 Rear Hub Nuts Z-S0570 Red Super Soft Leaf Springs Z-S0225 Shooter Shackles (Black) Z-S0250 T-Box Shackle Z-A0049 K44 Scale Rear Axle Z-A0048 K44 Scale Front Axle Z-T0058 Mickey Thompson 1.55 Baja MTZ Scale Tires Z-T0064 Mickey Thompson 1.55 Baja Claw TTC Scale Tires (pair) Z-T0056 Interco IROK 1.55 Scale Tires Z-S1079 RC4WD 1/10 Warn 9.
