VHF Marine Two-Way Radio RCA Communications Systems
Foreword Thank you for purchasing this company marine transceiver, you will find the professional and human oriented design of the transceiver during use. Read all instructions carefully and completely before using the transceiver. It is an abundant is a powerful marine radio, it id designed on IMO (International Maritime Organization) resolution. As adopting advance waterproof technology, the transceiver is with good waterproof, floating and flash functions.
Recommendation Clean the transceiver thoroughly with fresh water after exposure to saltwater, and dry it before operating. Otherwise, the transceiver's key, switches and controllers may become unusable due to salt crystallization. NOTE:DO NOT submerge the transceiver in water if there is any reason to suspect the waterproof protection may not be effective.
C O N TEN TS PREPARATION Preparation ............................................................................... 1 Supplied Accessories ......................................................... 1 Charging the Battery Pack .................................................. 1 Battery Pack ....................................................................... 2 Flexible antenna ................................................................. 2 Belt clip ..................................................
P R EPA R ATI O N Charging the Battery Pack Preparation 1. Connect the adaptor to the AC Power. 2. Rotate the jack in top of transceiver, connect it to the adaptor start to " and " " to indicate charging. charge, LCD appears " Supplied Accessories Carefully unpack the transceiver. We recommend that you identify items llisted in the following table before discarding the packing materials. If any item are missing or have been damaged, please contact dealer immediately.
Battery Pack Flexible Antenna To insert the battery pack: 1. Connect the supplied fixable antenna to the antenna connector, rotate it clockwise. 2. To remove it, rotate it counter-clockwise. Place the battery into the transceiver so it fits flat, and the securely attach the battery cover, as shown. Push the cover until the latch comes back to the locked position. Belt Clip Attach the belt clip to, or detach the belt clop from the transceiver.
PANE L D ESC R I PTI O N Pannel Description tagged channel, in a channel group. Hold for 1 second to set or clear the TAG for the display channel. While hold , turn ON the power to clear or set all TAG channels in the seteced channel group. 4. SCAN/DUAL Push to start or stop a normal or priority scan. Hold for 1 second to enter the Dual/Tri-watch mode. Push to exit the watch mode Hold this key and HI/LO key for 1 second, to activate the AquaQuake Function. 5.
While in the Set mode, push to select the setting or value of an item. Push to check TAG channels or change scanning direction during a scan. 9. [CH] Hold for 1 second, one or more times, to select a channel group from USA, International, and Canada. Push to return to the previous channel before selecting Channel 16 or the Calling channel. 10. ANTENA CONNECTOR Connect the supplied antenna here. 11. [DC 6V] Connect the adaptor or optional cable her.
BA SI C O PER ATI O N Turn ON/OFF 1. Press[ ] for 1 second to turn ON. ]for 1 second to turn OFF. 2. Press again[ Receiving and Transmitting Receiving 1. set the volume levels by push [VOL/SQL] , [▼] or [▲]. Adjusting the Volume Level The volume level can be adjusted using [VOL/SQL] and [▼] or [▲]. 1. Push [VOL/SQL] once to enter the volume adjustment mode. Then press [▼] or [▲] to adjust the volume level. The"VOL" icon starts blinking. The transceiver has 31 volume levels and OFF.
1. Push [CH] to select a regular channel. 2. Hold down [CH] for 1 second, one or more times,to select the desired channel group. The selectable channel groups are different, depending on the version. 3. Push [▲] or [▼] to select a channel. "A" appears when a simplex channel is selected. Call Channel Each regular channel group has separate leisure-use call channels. The call channel is monitored during Tri-watch.
Automatic Backlight 4. Push [▼] or [▲] to select desired call channel 5. Push [16/C] confirmed and save it , Push [CH] cancel and exit. This function is convenient for night time operation. The automatic backlighting can be activated in set mode. Push any key except for [PTT] to turn the backlighting ON. The backlighting is automatically turned OFF after 5 seconds.of inactivity. Lock Function Monitor Function The monitor function opens the squelch. Push [MONI] to active monitor function.
S CA N O PER ATI O N Scan Types Scanning is an efficient way to locate signals quickly over a wide frequency range. The transceiver has priority scan and normal scan. In addition, the weather alert and auto scan functions are available for standby convenience. These functions can be activated simultaneously, depending on the setting in set mode. NormalScan It searches through all TAG channels in sequence.However, unlike priority scan, Channel 16 is not checked unless channel 16 is set as a TAG channel.
DUALW ATC H / TR I - W ATC H Description Dualwatch monitors Channel 16 while you are receiving on another channel; Tri-watich monitors Channel 16 and the call channel while receiving another channel. Dualwatch/Tri-watch is convenient for monitoring channel 16 when you are operating on another channel. Operation 1. Push [SCAN/DUAL]for 1 second to start dual watch or tri-watch. "DW" blinks during dual watch;”TW” blinks during Tri-watch. A beep tone sounds when a signal is received on Channel 16.
SET M O D E Set Mode Items Set Mode Programming The set mode is used to channel the settings of transceiver's functions: beep tone function, priority scan function, scan resume timer, auto scan function, dual/tri-watch function , monitor key action, automatic backlighting, LCD contrast setting and power save function . Set Mode Operation 1. Turn OFF the power. 2. While holding down [VOL/SQL],turn ON the power to enter the set mode 3. Release [VOL/SQL], appears " Bp " 4.
no signal is received, and no operation is performed for 30 seconds. Dual/Tri-watch Function Set the watch type to Dualwatch or Tri-watch. Monitor Key Action The monitor key temporarily opens the squelch. This item sets the key action. Pu(PUSH): The monitor function is activated by holding down[MONI]. The squelch open while holding down the key. Ho(Hold): The monitor function is activated by holding down [MONI] for 1 second, the squelch stays open until any key is pushed.
VHF Marine Channel List Channel number USA INT 01 CAN Transmit Receive 01 01A 160.650 156.050 156.050 02 02 156.100 160.700 03 156.150 160.750 04 04A 05 05A 06 08 156.150 156.150 156.200 160.800 Channel number USA INT 21 21A 156.350 160.950 26 07A 156.350 156.350 27 08 156.400 156.400 28 156.450 156.450 156.500 156.500 11 11 11 156.550 156.550 12 12 12 156.600 156.600 13*1 13 13*1 156.650 156.650 86A 21A 157.050 157.050 69 69 69 156.475 156.
SPEC IF IC ATION General Frequency Range Receive Sensitivity ≤0.22μV RX：156.05MHz-162.025MHz Squelch Sensitivity ≤0.22μV Type of emission FM（16K0G3E） HUM and Noise ≥40dB Battery Pack 1500mAh Li-ion (DC 3.7V) Adjacent Channel Selectivity ≥70dB Frequency Stability ±10 PPM Spurious Response ≥70dB Operating Temperature Range -15℃～+55℃ Intermodulation ≥68dB Antenna Impedance 50 Audio Output Power ≥0.
T ROU B L ESH O OTI N G These types of errors are generally due to improperly connected , the operation caused by incorrect settings , or operator error caused due to incomplete programming . These problems are usually not caused by circuit failure . Before suspect intercom failure, please refer to the relevant section of this manual . PROBLEM The transceiver does not turn ON. POSSIBLE CAUSE SOLUTION The battery is exhausted. The battery pack is not correctly inserted.
Important Information RF Energy Exposure Information RF Energy Exposure Awareness And Control Information For Fcc Occupational Use Requirements Ibefore using the two-way portable radio, review the following important RF energy awareness and control information and operational instructions. Comply with this information and instructions in order to ensure compliance with RF exposure guidelines.e the capability to access information in that form.
Important Information Federal Communications Commission Regulations Before it was marketed in the United States, the Digital portable radio was tested to ensure compliance with FCC RF energy exposure limits for two-way portable radios. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements.
