Television User's Guide Retourner le cahier pour la version française TOCOM 1616362B Changing Entertainment. Again. 1616362B.
Important Information CAUTION This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts. RISK OF ELECTRIC SHOCK DO NOT OPEN Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. This symbol indicates important instructions accompanying the product.
Table of Contents Chapter 1: Connections & Setup Things to Consider Before You Connect ....................................................................... 3 Protect Against Power Surges .................................................................................................................... 3 Protect Components from Overheating .................................................................................................. 3 Position Cables Properly to Avoid Audio Interference .............
Table of Contents USA V-Chip Rating System .......................................................................................................................16 Canadian English V-Chip Rating System ..............................................................................................16 Canadian French V-Chip Rating System ...............................................................................................17 USA V-Chip TV Rating Limit ..................................................
Chapter 1: Connections & Setup Things to Consider Before You Connect Protect Against Power Surges • Connect all components before you plug any of their power cords into the wall outlet. • Turn off the TV and/or component before you connect or disconnect any cables. • Make sure all antennas and cables are properly grounded. Refer to the Important Safety Instructions packed separately. Protect Components from Overheating • Don’t block ventilation holes on any of the components.
Connections & Setup TV (back panel) VCR R AUDIO OUT TO TV CH3 CH4 OUT R L 2 IN FROM ANT VIDEO Y PB L VIDEO 2 L VIDEO 3 R IN L OUT VIDEO R AUDIO L/MONO VIDEO R PR PB Y PR VIDEO 1 TV ANT 3 R From Cable or Antenna L/MONO AUDIO VIDEO S-VIDEO IN 1D 1B DVD 1A 1C* OUT Pr Pb Y R L VIDEO S-VIDEO * If you connect an S-Video cable, you must connect the audio cables to the VIDEO 1 AUDIO jacks on the back of the TV, not the VIDEO 2 AUDIO jacks. TV + DVD + VCR 1.
Connections & Setup Explanation of Jacks This section describes the jacks you can use to make connections. There are several ways to connect components to your TV. TV ANT Lets you connect a coaxial cable to receive the signal from the antenna, cable, cable box, or if using the example on page 4, a VCR. VIDEO 1 R L/MONO VIDEO S-VIDEO IN AUDIO VIDEO 1 VIDEO, AUDIO R and L/MONO INPUTS Lets you connect a component such as a VCR, DVD player, or laserdisc player.
Connections & Setup The Front of Your TV Front Input Jacks VIEW MESSAGE READY ADVISORY WATCH HEAR VOICE STOP ALARM MENU/OK CH CH VOL VOL The TV has front input jacks for your convenience: one set of audio/video inputs, an S-Video and a headphone jack. These jacks are towards the front of the TV on the side. To access the component you connected to the front of the TV, press the INPUT button on your remote until FRNT appears on the screen.
Connections & Setup ON OFF VCR1 DVD How to Use the Remote Control to Complete the Initial Setup TV The technical term is “Navigation”– how you move through the on-screen menus. The method is the same throughout the menu screens: highlight your choice and select it. VCR2 AUX SAT•CABLE MUTE SKIP To highlight a menu item, press the arrow buttons on the remote to highlight one of the items listed on the screen. Use the up or down arrow button to move up or down.
Chapter 2: Using the Remote Control Indicator ON OFF VCR1 DVD VCR2 TV AUX SAT•CABLE MUTE SKIP VOL VOL CH + CH - SOUND GO BACK GUIDE INFO OK MENU 1 CLEAR 3 2 4 5 6 7 8 9 WHO•INPUT Button Descriptions for TV Mode Arrows Used to point to different items in the TV menu and to adjust the menu controls. Indicator Indicates the programming mode when programming the remote to control components. Lights when you press a valid button on the remote.
Using the Remote Control REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE If programmed, provides transport control for some remote-controllable VCRs and DVD players. SAT•CABLE Puts the remote in SAT•CABLE mode and, if auto tuning enabled, will turn on the TV and tune to the correct video input channel. VCR1 Puts the remote in VCR mode and, if auto tuning is enabled, will turn on the TV and tune to the correct video input channel.
Using the Remote Control Using Automatic Code Search The following instructions can be used to program the remote to operate each of your components. If you want to stop the automatic code search without programming any of your components, press CLEAR until the indicator on the remote turns off. 1. Turn on the component you want to operate (VCR, etc.) 2. Press and hold the component button you want to program (VCR1, etc.).
Using the Remote Control How to Use the Remote After You’ve Programmed It Because this universal remote can control several different components (TV, DVD, VCR, satellite receiver, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote to control the TV, you would press the TV button to put the remote into TV mode before you could control the TV. 1.
Using the Remote Control VCR Codes continued Nikko ........................................................................................ 2014 Noblex ...................................................................................... 2013 Olympus ................................................................................... 2021 Optimus ......................................................................... 2014, 2131 Optonica .....................................................................
Using the Remote Control Cable Box Codes continued Regal ................................................................................. 5022, 5035 Regency ....................................................................................... 5017 Rembrandt ................................................................................... 5003 Runco ........................................................................................... 5026 Samsung ...................................................
Chapter 3: Using the TV’s Features Channel Banner There are several items that might appear on-screen when you press the TV or INFO button on the remote. This display is called the Channel Banner. The following list describes the items on the Channel Banner screen (left to right and top to bottom). SAP Stereo 06 ABCDEF KidPass: 2:24 Skip: 0:30 CC 07:18am X SAP Displayed when the current channel is broadcasting SAP (Second Audio Program) information. Displayed when V-Chip has been activated.
Using the TV’s Features Set VCR1 Lets you set up the channel the TV tunes to when you press the VCR1 button. Set VCR2 Lets you set up the channel the TV tunes to when you press the VCR2 button. Set SAT/CABLE Lets you set up the channel the TV tunes to when you press the SAT•CABLE button. Set DVD Lets you set up the channel the TV tunes to when you press the DVD button. 5. Press the right arrow button to select the choice that matches the way you have the component connected to this TV, and press OK.
Using the TV’s Features How V-Chip Works V-Chip reads the program’s age-based rating (TV-MA, TV-14, etc.) and content themes [(Violence (V), Adult Language (L), etc.)]. If you have blocked the rating and/or content themes that the program contains, you will receive the message This channel has not been approved for viewing. Change channel or press OK to enter password and temporarily deactivate the Parental Control.
Using the TV’s Features 14+ (Viewers 14 and over) Programming contains themes or content which may not be suitable for viewers under the age of 14. Parents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent use of profanity.
Using the TV’s Features USA V-Chip TV Rating Limit PARENTAL CONTROL The V-Chip TV Rating Limit lets you decide which TV programs can and cannot be viewed. To set TV programming limits: Go Back V-Chip active USA V-Chip ... Canada V-Chip USAPrgms. V-CHIP Exempt ... KidPass Active Go Back KidPass Movie Ratings Lock Fr. Panel TV Ratings Change Passwd. 1. Choose Parental Control from the MAIN MENU (the PASSWORD screen appears the first time you enter the Parental Control menu).
Using the TV’s Features Blocking Age-Based Ratings Hierarchy of Age-Based Ratings TV-MA Mature Audience Only You can automatically block all program ratings above a specified age-based rating level. TV-14 Parents Strongly Cautioned To block programs with higher ratings: TV-PG Parental Guidance Suggested TV-G General Audience TV-Y7 Directed to Children 7 years and older TV-Y All Children 1.
Using the TV’s Features 1. Determine the content themes you want to change to (V) View. 2. Press the down arrow button to scroll to the rating whose content theme you want to change, such as B under language (L) corresponding with TV-14. 3. Press the right arrow button to move the highlight to a particular content theme status. 4. Press the OK button to change the status back to V.
Using the TV’s Features Unlocked All unrated programs are available. Locked All unrated programs are not available. Note: You must remember to activate V-Chip for rating limits to take effect. Press the down arrow to highlight Exempt Prgms. Then press the right arrow to toggle between the lock and unlock icon. KidPass The KidPass feature allows parents to set a certain amount of time every day of the week that a child can watch TV. To set KidPass: 1. Select Parental Control from the main menu. 2.
Chapter 4: Using the TV’s Menu System Sound Menu SOUND Treble Increases or decreases the treble. Go Back Treble Bass Increases or decreases the bass. Bass Balance Sound Type Balance Press the right arrow to increase the audio output in the right speaker; press the left arrow to increase the audio output in the left speaker. Stereo . . . SAP Auto Vol Level Audio Output Fixed . . .
Using the TV’s Menu System Auto Color Turn this option on to automatically correct the color of the picture. This is especially useful for tracking realistic flesh tone colors as you switch from channel to channel. Color Warmth Press the right arrow to scroll through the color adjustments: Cool for a more blue palette of picture colors; Normal; and Warm for a more red palette of picture colors. Brightness Adjusts the brightness of the picture.
Using the TV’s Menu System Closed captioning is not available on all channels at all times. Only specific programs encoded with closed-captioning information are applicable. When a program is closed captioned, CC is displayed in the channel banner. Go to Chapter 3 for more information about the channel banner. The closed caption options are: CC Display Lets you choose the way closed captioning information is shown on the screen. Off No captioning information displayed.
Chapter 5: Other Information Troubleshooting Most problems you encounter with your TV can be corrected by consulting the following troubleshooting list. Note for U.S. customers: If you prefer, we can provide you with the name of an Authorized Service Representative who will visit your home for a fee to install your electronic entertainment system and to instruct you in its operation. For details about this service, call 1-888-206-3359.
Other Information Can’t select certain channel • • Channel may be blocked or not approved through the V-Chip. If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR). Noisy stereo reception • May be a weak station. Access the SOUND menu, highlight Sound Type and then choose Mono. No picture/blue screen, no sound but TV is on • • • Maybe the signal type is set wrong. Go to page 23 for detailed instructions.
Other Information The V-Chip won’t let me watch a program even though it’s not rated as violent. • Maybe the movie was given an NR (Not Rated) status. After you block movie ratings, you must set NR to View separately in order to view movies with an NR rating. Care and Cleaning CAUTION: Turn OFF your TV before cleaning. You can clean the TV as required, using a soft lint-free cloth. Be sure to occasionally dust the ventilation slots in the cabinet to help assure adequate ventilation.
Other Information • Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service. For rental firms, proof of first rental is also required. What your warranty does not cover: • Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your product. Any additional information should be obtained from your dealer.) • Installation and related adjustments.
Other Information Accessory Information Below are accessories available to compliment your product. Prices are subject to change without notice. All accessories are subject to availability. A shipping and handling fee will be charged upon ordering, and we are required by law to collect the appropriate sales tax for each individual state, county and locality to which the merchandise is being sent.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Téléviseur Guide de l’utilisateur Flip over for English TOCOM 1616362B Transforme encore le divertissement. 1616362B.00_covFr.
Information importante ATTENTION Ce symbole indique que ce produit comporte une double isolation entre la tension de secteur dangereuse et les pièces accessibles à l’utilisateur. Pour réparer, n’utilisez que des pièces de rechange identiques. RISQUE DE CHOC ÉLECTRIQUE, NE PAS OUVRIR Attention : Afin de réduire le risque de choc électrique, ne pas enlever le couvercle (ou l’arrière). Ne contient aucune pièce réparable par l’utilisateur.
Table des matières Chapitre 1 : Connexions et réglage Points à prendre en considération avant d’effectuer les connexions ...................................... 3 Prévenez les surtensions ................................................................................................................................................ 3 Protégez vos composants contre la surchauffe ......................................................................................................
Table des matières Visionnement de thèmes particuliers ...................................................................................................................... 19 Blocage pour le filtrage canadien ............................................................................................................................. 20 Filtrage des films (V-chip) ...........................................................................................................................................
Chapitre 1 : Connexions et réglage Points à prendre en considération avant d’effectuer les connexions Prévenez les surtensions • Connectez tous les composants avant de brancher leurs cordons d’alimentation dans la prise murale. • Éteignez le téléviseur et (ou) le composant avant de connecter ou de déconnecter un câble. • Assurez-vous que toutes les antennes et tous les câbles sont mis à la terre correctement. Reportez-vous aux Informations de sécurité importantes, emballées séparément.
Connexions et réglage Téléviseur (panneau arrière) MAGNÉTOSCOPE R AUDIO OUT TO TV CH3 CH4 OUT R L 2 IN FROM ANT VIDEO Y PB L VIDEO 2 L VIDEO 3 R IN L OUT VIDEO R AUDIO L/MONO VIDEO R PR PB Y PR 3 VIDEO 1 TV ANT R du câble ou de l’antenne L/MONO AUDIO VIDEO S-VIDEO IN 1D 1B DVD 1A 1C* OUT Pr Pb Y R L VIDEO S-VIDEO * Si vous connectez un câble S-vidéo, vous devez connecter les câbles audio aux prises VIDEO 1 AUDIO à l’arrière du téléviseur et non aux prises VIDEO 2 AUD
Connexions et réglage Explication des prises Cette section décrit les prises que vous pouvez utiliser pour les connexions. Vous pouvez connecter des composants à votre téléviseur de plusieurs façons. TV ANT Permet de connecter un câble coaxial pour recevoir le signal de l’antenne, du câble, du câblosélecteur ou, selon l’exemple de la page 4, un magnétoscope.
Connexions et réglage Avant du téléviseur Prises d’entrée avant VIEW MESSAGE READY ADVISORY WATCH HEAR VOICE STOP ALARM MENU/OK CH CH VOL VOL Le téléviseur est équipé de prises d’entrées pratiques à l’avant : un groupe d’entrées audio/vidéo, S-vidéo et une prise de casque d’écoute. Ces prises sont situées vers l’avant du téléviseur, sur le côté.
Connexions et réglage ON OFF VCR1 DVD Utilisation de la télécommande pour effectuer l’installation initiale TV On utilise le terme technique de « Navigation » pour décrire les déplacements dans les menus affichés à l’écran. La méthode reste la même dans tous les menus : mettez votre choix en surbrillance et sélectionnez-le. VCR2 AUX SAT•CABLE MUTE SKIP Pour mettre en surbrillance un élément du menu, appuyez sur les touches à flèche de la télécommande.
Chapitre 2 : Utilisation de la télécommande Description des touches pour le mode TV Voyant ON OFF VCR1 DVD VCR2 TV AUX SAT•CABLE MUTE SKIP Flèches Utilisées pour pointer vers différents articles du système de menus du téléviseur et régler les commandes dans les menus. (0 à 9) Touches numériques Permettent d’entrer directement le numéro du canal et de régler l’horloge au moyen de la télécommande.
Utilisation de la télécommande REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE (Arrière, lecture, Avant, Enregistre-ment, Arrêt, Pause) Si elle est programmée, permet la commande du transport pour certains magnétoscopes et lecteurs DVD télécommandables. SAT•CABLE Met la télécommande en mode SAT•CABLE et, si la syntonisation automatique est activée, allume le téléviseur et syntonise le canal d’entrée vidéo approprié.
Utilisation de la télécommande Utilisation de la recherche automatique du code Les instructions qui suivent peuvent servir à programmer la télécommande pour qu’elle commande chacun de vos composants. Si vous voulez arrêter la fonction de recherche automatique du code sans programmer aucun composant, appuyez sur CLEAR jusqu’à ce que le voyant de la télécommande s’éteigne. 1. Allumez le composant que vous voulez commander (magnétoscope, etc.). 2. Appuyez sur la touche du composant à programmer (VCR1, etc.
Utilisation de la télécommande Utilisation de la télécommande une fois programmée Étant donné que cette télécommande universelle peut commander plusieurs appareils différents (téléviseur, lecteur DVD, magnétoscope, récepteur satellite, etc.), elle utilise des modes de fonctionnement déclenchés par les touches de composants. Par exemple, si vous voulez que la télécommande commande le téléviseur, appuyez sur la touche TV pour mettre la télécommande en mode TV avant de pouvoir commander le téléviseur. 1.
Utilisation de la télécommande Codes pour magnétoscopes (suite) Midland ............................................................................... 2053 Minolta .......................................................... 2055, 2056, 2107 Mitsubishi ......... 2029, 2055, 2056, 2065, 2066, 2067, 2069, 2070, 2071, 2072, 2073, 2074, 2106, 2113, 2123 Montgomery Ward .................................................. 2075, 2131 Motorola ...................................................................
Utilisation de la télécommande Codes pour câblosélecteur (suite) Jerrold ...... 5003, 5005, 5007,5018, 5023, 5024, 5046, 5053 Magnavox ......................................................................... 5025 Memorex ............................................................................ 5026 Movie Time ................................................. 5002, 5027, 5028 NSC ............................................................... 5002, 5027, 5028 Oak .........................................
Chapitre 3 : Utilisation des fonctions du téléviseur Bannière de canal Plusieurs articles risquent d’apparaître lorsque vous appuyez sur les touches TV ou INFO de la télécommande. Cet affichage est appelé Bannière de canal. La liste suivante décrit les éléments de l’écran Bannière de canal (de gauche à droite et de haut en bas). SAP SAP Stéréo 06 ABCDEF KidPass : 2:24 Saut : 0:30 CC 07:18am X Affiché lorsque le canal actuel diffuse un SAP (deuxième piste audio). Affiché lorsque le V-chip a été activé.
Utilisation des fonctions du téléviseur VCR1 Vous permet de régler le canal syntonisé par le téléviseur à partir de la touche VCR1. VCR2 Vous permet de régler le canal syntonisé par le téléviseur à partir de la touche VCR2. SAT/CABLE Vous permet de régler le canal syntonisé par le téléviseur à partir de la touche SAT•CABLE. DVD Vous permet de régler le canal syntonisé par le téléviseur à partir de la touche DVD. 5.
Utilisation des fonctions du téléviseur Fonctionnement du V-chip Le V-chip indique au logiciel la catégorie d’âge visée (TV-MA, TV-14, etc.) et les thèmes abordés (Violence [V], Langage adulte [L], etc.). Si vous avez bloqué le code ou le thème de l’émission, le message suivant est affiché : Canal sous contrôle parental. Changez de canal ou appuyez sur OK pour entrer le mot de passe et désactiver temporairement le Contrôle parental.
Utilisation des fonctions du téléviseur 14+ (Spectateurs de 14 ans et plus) L’émission contient des thèmes ou un contenu qui pourrait ne pas convenir à des spectateurs de moins de 14 ans. Les parents sont sérieusement avisés de faire preuve de jugement avant d’autoriser le visionnement à des enfants de moins de 14 ans. Directives sur la violence : Pourrait contenir des scènes intenses de violence. Pourrait traiter de façon réaliste de thèmes adultes et de problèmes sociaux.
Utilisation des fonctions du téléviseur Filtrage TV pour les É-U CONTRÔLE PARENTAL L’option de Filtrage TV vous permet de décider les émissions télévisées qui peuvent et ne peuvent pas être regardées. Pour fixer la limite : Retour V-Chip actif V-Chip USA ... V-Chip Canada V-CHIP USA Emis. non cod. ... KidPass actif Retour KidPass Filtrage films Bloq. clavier Filtrage TV Changer mot p. 1.
Utilisation des fonctions du téléviseur Blocage des catégories d’âge Hiérarchie des catégories d’âge Vous pouvez bloquer automatiquement toutes les émissions dont la catégorie d’âge est supérieure à un niveau spécifié. TV-MA Adultes seulement TV-14 Parents sérieusement mis en garde TV-PG Surveillance parentale suggérée TV-G Tout public TV-Y7 Destiné aux enfants de 7 ans et plus TV-Y Enfants de tous âges Pour bloquer les catégories supérieures : 1.
Utilisation des fonctions du téléviseur 1. Déterminez les thèmes que vous voulez changer à (V) Voir. 2. Appuyez sur la touche à flèche vers le bas pour atteindre la classification dont vous voulez modifier le thème, comme B sous la langue (L) correspondant à TV-14. 3. Appuyez sur la touche à flèche vers la droite pour déplacer la surbrillance vers un état de thème particulier. 4. Appuyez sur la touche OK pour ramener son état à V.
Utilisation des fonctions du téléviseur Déverrouillé Toutes les émissions sans code sont disponibles. Verrouillé Aucune émission sans code n’est disponible. Nota : Vous devez verrouiller le V-chip pour que les filtrages entrent en vigueur. Appuyez sur la touche à flèche vers le bas pour mettre en surbrillance Emiss. non cod. Appuyez ensuite sur la flèche vers droite pour alterner entre l’icône verrouillé et déverrouillé.
Chapitre 4 : Utilisation du système de menus du téléviseur SON Menu Son Retour Aigus Augmente ou diminue les sons aigus. Aigus Basses Augmente ou diminue les basses. Basses Balance Type de son Balance Appuyez sur la flèche de droite pour augmenter la sortie audio du haut-parleur droit; appuyez sur la flèche de gauche pour augmenter la sortie audio du haut-parleur gauche. Stéréo . . . SAP Niveau auto. Sortie audio Fixe . . .
Utilisation du système de menus du téléviseur Lumière Sert à régler la luminosité de l’image Contraste Sert à régler la différence entre les zones claires et foncées de l’image. Couleur Sert à régler la richesse de la couleur. Contour Sert à régler la netteté des contours dans l’image. Nota : L’option de contour n’est pas disponible pour le canal d’entrée vidéo des composants (CVID2 ou CVID3). Teinte Sert à régler l’équilibre entre les niveaux de rouge et de vert.
Utilisation du système de menus du téléviseur Sous-titrage Vous permet de choisir à quel moment les sous-titres sont affichés à l’écran. Non Aucun sous-titre ne s’affiche. Oui Les sous-titres sont toujours affichés, s’ils sont disponibles. Si son=0 Affiche les sous-titres, si disponibles, lorsque le son du téléviseur est coupé au moyen de la touche MUTE. Les sous-titres ne sont pas affichés lorsque le son n’est pas coupé. Mode ST Vous permet de choisir le mode d’affichage des sous-titres à l’écran.
Chapitre 5 : Autres informations Dépannage La plupart des problèmes posés par votre téléviseur peuvent être corrigés en consultant la liste de dépannage qui suit. Nota pour les clients des États-Unis : Si vous préférez, nous pouvons vous fournir le nom d’un représentant de service autorisé qui, moyennant des frais, se rendra chez vous pour installer votre système de divertissement électronique et pour vous montrer à l’utiliser. Pour obtenir des détails sur ce service, appelez le 1 888 206-3359.
Autres informations Impossible de sélectionner certains canaux • Le canal peut être bloqué ou non approuvé dans le menu V-chip. • Si vous utilisez un magnétoscope, vérifiez si le bouton TV/VCR du magnétoscope est dans le bon mode (appuyez sur le bouton TV/VCR de votre magnétoscope). Réception stéréo bruitée • La station est peut-être faible. Accédez au menu SON, mettez en surbrillance Type de son, puis sélectionnez Mono.
Autres informations Le V-chip m’empêche de visionner une émission, même si elle n’est pas dans la catégorie « Violence » • Il se peut que le film ne soit pas classé dans une catégorie NR (sans code). Après avoir bloqué certaines catégories de films, vous devez régler séparément l’état de NR à Voir View si vous voulez voir les films de catégorie NR. Entretien et nettoyage ATTENTION : ÉTEIGNEZ le téléviseur avant le nettoyage.
Autres informations Ce que ne couvre pas votre garantie : • La formation client. (Votre Manuel de l’utilisateur décrit l’installation, les réglages et le fonctionnement de votre produit. Toute information supplémentaire devrait être obtenue auprès de votre détaillant.) • L’installation et les réglages connexes. • Les problèmes de réception de signal qui ne sont pas causés par votre téléviseur. • Les dommages dus au mauvais usage ou à la négligence. • Les piles. • Les fusibles remplaçables par le client.
Autres informations Informations sur les accessoires Les accessoires ci-dessous peuvent être ajoutés à votre produit. Les prix sont sujets à des changements sans préavis. Tous les accessoires sont sujets à la disponibilité. Des frais d’expédition et de manutention sont applicables et la loi nous oblige à percevoir la taxe de vente en vigueur dans chaque province, comté et localité où la marchandise est expédiée.
Cet équipement a été soumis à des essais sur prototype et déclaré conforme aux limites stipulées pour un dispositif numérique de classe B, conformément aux spécifications de la partie 15 du Règlement de la FCC. Ce règlement a pour but d’assurer une protection raisonnable contre le brouillage nuisible dans une installation résidentielle.