MODEL NO. RPJ143-50DISP MULTIMEDIA PROJECTOR Ideal for dark viewing environments for optimal performance. Please note:Projector brightness is measure in ANSI lumens. Your viewing environment is the deciding factor on how many lumens your projector needs. PLEASE READ BEFORE OPERATING THIS EQUIPMENT This product is manufactured and sold by SHENZHEN KEJINMING ELECTRONIC CO.,LTD.
Important Safety Instruc"ons 1. Read these Instrucons. 2. Keep these Instrucons. 3. Heed all Warnings. 4. Follow all instrucons. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any venlaon openings. Install in accordance with the manufacturer’s instrucons. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that product heat. 9.
Addi onal Warnings and Precau ons 1. Do not look directly into the projector light. 2. Don’t touch the project lens 3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5.
FCC Warning This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - P1 Additional Warnings and Precautions - - - - - - - - - - - - - - - - - - - - - - P2 FCC Warning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 In The Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 Table of Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P4 Remove & Close the Lens Cover Plac
Remove & Close The Lens Cover Remove the lens cover before using Close the lens cover when unit not using REMOVE CLOSE LENS COVER LENS COVER Placing Your Projector Your projector can be installed in four different configurations ( see picture below): Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.
Square /Rectangle It is recommended to move the projector as close to center of screen. Distance Between The Projector And Screen Measure the distance between the projector and where you want to position the screen. This is the projection distance.
Follow below picture to adjust the vertical location. SCREEN SCREEN PROJECTOR VERTICAL DIMENSION VERTICAL DIMENSION PROJECTOR SCREEN VERTICAL DIMENSION PROJECTOR Adjust this knob ( ANGLE ADJ. knob) to ¿ne- tune the display angle to higher. Adjust The Focus And Keystone Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible.
Controls Of Remote Mute Press to mute volume. Power Press to power ON. Press twice to power OFF. Back / Fwd Press to search through an individual chapter or track. Previous / Next Press to skip between chapters or tracks. Stop Press to stop playback. Press t FLIP VOL – VOL + Flip display image 180°. SOURCE Play/Pause Press to play or pause an individual chapter or track. VOL+ / VOL− Press to adjust audio level. Source Press to select media source (AV, PC, HDMI, MEDIA). Exit Press to exit menus.
Controls Of Projector 1 2 3 4 5 9 1011 12 13 14 15 17 6 7 8 20 16 18 19 2. 3. 4. 5. 6. RETURN NAVIGATION OK TRAPEZOIDAL ADJ. Knob FOCUS ADJ. Knob LENS EAR PHONE Jack AV IN Jack 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 9 Micro SD Card HDMI Port 1 HDMI Port 2 USB Port DC IN jack VGA Port POWER on Indicator IR Window ( Rear Side) IR Window ( Front Side) ANGEL ADJ.
Controls Power Source Press to change media source mode. Menu Press to access on-screen menus and options. Arrows/OK Press to navigate onscreen menus and make selections. Back Press to return to a previous page or setting in the onscreen menus. Install Power Adapter Follow below picture to connect power adapter Connect small end of adapter FIRST. Plug the adapter body to power outlet. 10 Press to power on the projector.
Connect HDMI Show The Image On Projector Screen Follow below picture to connect HDMI cable and device. 1. Turn off the unit before connect HDMI cable. light GREEN 3. Press the / SOURCE device will show on projector screen. There are 2 HDMI input, HDMI1 interface corresponds to HDMI 1 in SOURCE mode , and HDMI2 interface corresponds to HDMI 2 in SOURCE mode. 4. Press the button twice to turn off unit power.
Connect VGA Show The Image On Projector Screen Follow below picture to connect VGA cable and device. 1. Turn off the unit before connect VGA cable. 2. Press the button twice to turn off power of your projector before connection. light GREEN 4. Press the / SOURCE will show on projector screen. 5. Press the button twice to turn off unit power.
Connect Audio Output ( Aux Out / Line Out / Earphones) Follow below picture to connect audio cable and device. 1. Press the button twice to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4.
Using microSD Card And USB Playback (Media Player) Install USB / microSD device: 1. Turn off the unit before install USB / microSD Card. 2. Install the USB device into USB port. GREEN. 4. Press the / SOURCE search the MEDIAPLAYER mode. OK OK the button to microSD card OK remote to start playback. 8. Press NOTE ďƵƩŽŶ ƚǁŝĐĞ ƚŽ ƚƵƌŶ ƉŽǁĞƌ FIRST. microSD device, Sub-Menu on Photo screen 1. When photo playback, press the &ŝŐƵre 1. screen show on lower ;ĮŐƵre 1). 2.
Using Bluetooth Playback Pairing to Bluetooth Wireless Speakers or Sound Bar NOTE: Bluetooth is OFF by default when the projector powers ON. Bluetooth can be turned ON or OFF from the OPTIONS Menu. 1.Enable Bluetooth on the receiver (external speakers, sound bar, etc.) to which you wish to connect. Devices such as smartphones, tablets, or computers are not Bluetooth receivers and will not connect to the projector.
Using Projector Menu 1.0 Press button to enter projector menu. Press again to previous status. Picture Mode Standard Contrast 50 Brithness 50 Color 50 Sharpness 50 Color Temperature Medium Aspect Ratio Auto Noise Reduction Middle Screen Use buttons to select manual page. OK This manual showed on right upper of view screen. 1. Picture Mode Select Vivid, User (custom), Soft ,or Standard 2. Contrast ,Brightness, etc Set Picture Mode to “User “ to adjust these settings 3.
Using Projector Menu 2.0 Press button to enter projector menu. Press again to previous status. Sound Mode Standard Treble 50 Bass 50 Balance 0 Auto Volume Off Surround Sound Off Use OK buttons to select manual page. This manual showed on right upper of view screen. 1. Sound Mode Select Music, Movie, User (custom), Sports ,or Standard 2. Treble, Bass Set Sound Mode to “User “ to adjust these settings 3. Balance Adjust the audio balance. 4. Surround Sound Turn Surround Sound ON or OFF.
Using Projector Menu 3.0 Press button to enter projector menu. Press again to previous status. OSD Language Bluetooth Restore Factory Default Panel Rotate Info English 0 OK Use buttons to select manual page. This manual showed on right upper of viewing screen. 1. OSD Language Select different language, Follow below figure. 2. Bluetooth Turn Bluetooth ON or OFF 3. Restore Factory Default Select Y or N. 4. Panel Rotate Select rotate 0, rotate 1, rotate 2, rotate 3.. 5.
Using Projector Menu 4.0 Press button to enter projector menu. Press again to previous status. Clock - - - Off Timer Off On Timer Off Sleep Timer Off Auto Sleep Never Use OK buttons to select manual page. This manual showed on right upper of viewing screen. 1. Clock-- -Select clock to Day, Month, Year, Hour ,and Minutes. 2. Off Timer Select turn off timer to Day, Hour ,and Minutes. 3. On Timer Select turn on timer to Day, Hour ,and Minutes. 4.
Specifications Light Source Type Brightness Output LED White light output ANSI: 50.7 Lumens Color Light output ANSI: 46 Lumens White brightness output ANSI: 30.8 Lumens Display Native Resolution 800 x 480 HDMI Input Supported 1080p , 1080i , 720p, 576i , 480p, and 480i Video Resolution. Power Consumption Operating 36W; Standby 1W Power Input DC 12V , 3.5A Connect Included Adapter Included Adapter Input AC100-240V,50/60Hz Connect DC input of unit Output DC12V , 3.
TROUBLESHOOTING Before resorting the maintenance service, please kindly check by yourself with the following chart. No Image is Projected or a "No Signal" message is displayed 1.Is the power hight on? If it is not on, check the projector is plugged into the mains, that the socket is switched on, and then press the power button on the projector. 2.Check the lens cover has been removed. 3.Check the cables are securely attached and installed as per the User Manual. 4.
