User’s Manual Free To Air VS2000 Digital Satellite Receiver
Table of Contents 1. SAFETY PRECAUTIONS 4 2. GENERAL FEATURES 5 3. HOW TO CONNECT YOUR RECEIVER 6 4. HARDWARE DESCRIPTION 8 5. SYSTEM SET-UP 12 6. MENU OPERATION 14 7. TROUBLE SHOOTING 29 8. TECHNICAL SPECIFICATIONS 30 9.
Important Safety Instruction 1) 2) 3) 4) 5) 6) 7) 8) Read all of these instructions. Save these instructions for later use. Follow all warnings and instructions marked on the product. Follow all instructions. Do not use the apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturerís instructions. Do not install near any heat sources such as radiators.
1. SAFETY PRECAUTIONS This receiver has been manufactured to satisfy the international safety standards. Please read the following recommended safety precautions carefully. MAIN SUPPLY : AC 95V~240V 50 / 60 Hz LOCATION : Locate the receiver indoor. Locate receiver away from potential hazards such as houseplants, lighting, raining and direct sunlight. OVERLOADING : Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock.
3. HOW TO CONNECT YOUR RECEIVER Please DO NOT plug in the main power supply cord until you have finished all the connections. 1) LOCATION OF THE RECEIVER Your receiver should be placed under proper ventilation. Don’ t put in completely enclosed cabinet that will restrict the flow of air, Resulting overheating. The location should be safeguarded from direct sunlight, excess moisture, rough handling or household pets. Avoid stacking other electronic components on the top of the receiver.
4. HARDWARE DESCRIPTION 4. A. FRONT PANEL 4. B. REAR PANEL 1) POWER : This key is used to turn the receiver on and off (stand by). POWER 2) CH : These keys are used to change the channels. CH VOL INFRARED SENSOR 3) VOL : These keys are used to increase and decrease the volume level manually. 4) INFRARED SENSOR : This is to receive the IR commands from the RCU. Do not block the view of the sensor. 1) LNB IN : This port is to connect the coaxial cable from LNB of your Dish.
4. C. REMOTE CONTROL UNIT 1) POWER : This is used to switch the receiver to ON/STANDBY mode. 2) MUTE : This key is used to toggle between normal and muted audio. 15) LAST : This key is used to return to the previous channel. AUDIO 16) AUDIO : This key is used to select the soundtrack list for the current service 3) 0-9 NUMERIC KEYS : These keys are used to enter numeric values and to 0 ~ 9 and also used to select audio mode. select the channel directly by entering its number.
5. SYSTEM SET-UP You can automatically detect and save all TV and Radio channels of a satellite as follows : System Connection ■ Connect the receiver to all peripheral devices. � Power On ■ Turn on the power of the receiver and other devices. � � Antenna Configuration Setting ■ Select Main Menu/Installation / Antenna Setup using CH ▲∙▼ & OK keys. ■ Select the satellite which you want to search using VOL ◀∙▶ keys. ■ Insert all information of your antenna.
6. MENU OPERATION keys( ▲ ). Press the“OK”key to confirm your selection. ▲ Also, you can use the“ ”key to select either TV channel list or Radio channel list. Once the channel is locked, every time you try to watch the program, you will be asked to enter PIN code. Press the“menu”key or“exit”key to return to previous menu. ▲ ▲ The main menu is classified into five sub menus which will carry out the various operation individually. 1. MAIN MENU Select the“Channel Lock”icon using the left/right keys (◀∙▶).
3. C. MOVE FAVORITE CHANNEL You can edit the favorite channel list, such as add/delete a channel or move its position, which facilitates you to easily find your favorite channel from the favorite channel list. The favorite channel is classified into one of 8 favorite categories depending on its genre. Select“Edit Favorite”menu in main menu, and you will be asked to enter your PIN code. You can find the following“Edit Favorite”screen by entering it. ▲ ▲ 3. A.
LNB Power 4. INSTALLATION “Installation” menu helps you to setup a variety of parameters necessary for receiving signal, add new service, upgrade the new software and reset the channel data. Select“Installation”menu in main menu, and you will be asked to enter your PIN code. You can find the following“Installation”screen by entering it. LNB Type LNB Freq. 22KHz Search option DiSEqC 1.0 Motor : Depending on the user’ s antenna LNB, you can supply either LNB power by setting“ON”or not by setting“OFF” .
You can see the progressive status of channel searching. 4. A. 3 USALS -Please go to Antenna Setup and select USALS from motor. -Press F1 then Pop-up will be appeared. -Press arrow button to write Longitude -Press arrow button to write Latitude, then OK to work. If you cannot find the desired transponder from the transponder list, you can add it by inputting appropriate parameter values for a new transponder using the“F1”key.
4. C. PARENT CONTROL This function prevents children or unauthorized persons from watching programs. Also you can change PIN(Personal Identification Number) code. Select“Parental Control”menu in“Insttallation” menu, and the following screen will be displayed. 4.C.1 Receiver Lock Time Mode Time Adjustment Current time Summer Time To lock receiver, select“Receiver Lock”in the“Parental Control”menu and change it to“On” mode using the“left/right”keys (◀∙▶). On time Off time 4.C.
7. CHANNEL LIST 5. SYSTEM SETTINGS This menu helps you to Set up video output mode, Ianguage, screen type and Select“System Settings”menu in main menu This menu helps you to easily select the channel that you want to watch. The channel list is separately constructed for each satellite. Press“OK”key, and the following screen will be displayed. You can get the information of channel number, channel name, and whether the program is scrambled or locked.
11. MULTI PICTURE When you press”GUIDE” key again, Daily Guide will be displayed. You can see all events for selected chanel. You can use the Multi-picture Function using F1 key. You can watch four, six or nine pictures at the same time using this function. And select the number of pictures using (▲,▼) keys and press OK. After that, you can see the Multi-Picture Screen. Also you can select the channel using(◀,▶ ▲,▼) keys and OK key in the Multi-picture Screen.
7. TROUBLE SHOOTING Mode : You can select this to “Default” or “User” When “Mode” is “User” , you can change each color value. Brightness Contrast Saturation Sharpness : If your receiver connected to TV by using “VIDEO” or “S-VIDEO” Connector , these items will change the color setting of TV screen. M_B_Y M_G_U M_R_V : If your receiver connected to TV by using “Component cable “(Y-Pb-Pr)” , these three items will change the color setting of TV screen.
8. TECHNICAL SPECIFICATIONS 5. Audio Decoder 1. Power Supply Type Input Voltage Fuse Rating : SMPS : AC 95V~240v 50Hz / 60Hz : 250V/T2A 2. Tuner Input Frequency Input Signal Level Input Impedance Connector Type LNB Power Supply 22KHz Tone DiSEqC Channel Selection : 950�2150MHz : -65�-25dBm : 75Ϊ Unbalanced :‘F’Type Female : 13V/18V, Max 500mA with Short Circuit Protection : Frequency 22± 4KHz, Amplitude 0.6±0.2Vpp : 1.0 & 1.
32 33
Brand List for TV Brand List for TV 34 35
