Bullet Feeder – Pistol Kit PRODUCT INSTRUCTIONS
WARNING Before using the RCBS Bullet Feeder – Pistol Kit, read these instructions carefully to fully learn how to safely operate the related reloading equipment. Failure to properly operate the related reloading equipment can result in severe personal injury and/or equipment damage. If you have any questions while assembling or operating this tool, Call us at 1-800-533-5000 or 1-530-533-5191 Monday – Thursday 6:30 am – 4:00 pm Pacific Time (hours may vary) Or email us at rcbs.tech@atk.
WARNING/CAUTION PRIMERS AND POWDER • Store primers and powder beyond the reach of children and away from heat, dampness, open flames and electrical equipment. Avoid areas where static electricity is evident. • DO NOT use primers of unknown identity. • Dispose of unknown primers in accordance with applicable regulations. • Keep primers in the original factory container until ready to use. Return unused primers to the same factory packaging for safety and to preserve their identity.
UNPACKING Refer to the list below to Identify parts as you unpack your new Bullet Feeder – Pistol Kit. 1. Bowl assembly 2. Upper Support Tube 3. Lower Support Tube 4. Support Foot 5. Power Supply and Plug adapters 6. Bullet Die body 7. Continuous Spring Tubes 8.
ASSEMBLY Attach the Lower Support Tube to the Support Foot using two 10-24x1 ½ SHCS (A)(see photo 1). Attach the Upper Support Tube to the Lower Support Tube using two ¼-28x 1 ½ BHCS and ¼ Flat Washers(B)(see photo 1). The Support height is adjustable depending on the type of press that you will be using the Bullet Feeder with. INSTALLATION Bolt the Bullet Feeder – Pistol Kit to the reloading bench or table using the slots provided in the Support Foot casting.
When you are ready to load, fill the Bowl with ~100 bullets and connect the Power Supply. The Bowl will run until the feed Tubes fill up with bullets. Add another ~100 bullets to bowl. You are now ready to begin your loading session. Install the Bullet Guide into the die body, the tapered inner portion is the “top” of the guide. Bullet guides are stamped on the side for identification.
Bowl Assembly There are two “wipes” in the bowl assembly. These are designed to prevent a double stack of bullets. With the power disconnected, rotate the Sorting Plate until one of the grooves is in line with the first “wipe”. Place a bullet into the groove, loosen the lock nut and adjust the “wipe” in or out until it clears the bullet by 1/8”1/4”, tighten the locknut.
TROUBLESHOOTING If correctly oriented bullets fall off of the sorting plate too early, change to a shallower Bowl angle adjustment. Move the Bracket Pin from the 45 or 40 degree position to the 40 or 35 degree position. 35°position-middle If changing the angle does not correct the problem, install the Shut Off into the bowl. MAINTENANCE Periodically wipe down the inner part of the Bowl and Bullet Wheel to remove dust and debris.
21 39 40 38 41 37 19 14 54 16 20 17 15 42 22 32 23 12 43 11 34 13 10 44 25 35 26 45 27 24 46 3 47 5 48 8 9 49 6 53 7 2 1 4 -9-
Part Number 781205 781208 181219 181233 781207 181218 186214 180072 181234 781200 781204 187211 181231 781201 181222 181217 181215 181221 181203 181237 781221 181206 187217 781203 181204 181230 181223 181239 181238 181228 181227 781206 781225 109603 181220 181229 181224 109604 781210 181240 181236 181207 781226 181235 781224 181242 781215 781223 781219 187546 181211 781217 787500 781227 82350 Bullet Feeder - Pistol Kit Description Support Foot Support Tube Lower Tube Cap 10-24 x 1-1/2 BHCS Support Tube Upp
- 11 -
PRECISIONEERED RELOADING EQUIPMENT We think that we make the very best reloading equipment in the world. If you agree, please tell your friends. If you disagree, tell us we want to do something about it! Customer Service 1-800-533-5000 (US or Canada) or 530-533-5191 Hours: Monday - Thursday, 6:30am - 4:00pm Pacific Time (hours may vary) e-mail: rcbs.tech@atk.com or visit our website at www.rcbs.com RCBS 605 Oro Dam Blvd.