R.A.S.S.
IMPORTANT Before using the RCBS R.A.S.S. Bench, read these instructions carefully to fully learn how to safely operate the related equipment. Failure to properly operate certain equipment can result in severe personal injury and/or equipment damage. If you have any questions while assembling or operating this product, call us at 1-800-533-5000 or 1-530-533-5191 Monday – Thursday 6:30 a.m. to 3:00 p.m. Pacific Time The instruction manual contains specific safety and operating information.
WARNING: FIREARM RESTS ARE NOT INTENDED FOR USE IN OR ON ANY MOTORIZED VEHICLE OR TRAILER UNLESS SECURED BY A PROPERLY DESIGNED MOUNTING SYSTEM AVAILABLE FROM THE MANUFACTURER. FAILURE TO COMPLY WILL RESULT IN AN UNSAFE FIREARM CONDITION THAT MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. WARNING: UNLOAD FIREARM, OPEN FIREARM ACTION AND ENGAGE FIREARM SAFETY BEFORE USE WITH FIREARM REST. DO NOT REACH IN FRONT OF FIREARM MUZZLE TO MAKE ADJUSTMENTS OR MANIPULATE FIREARM REST.
UNPACKING Open the box to remove, identify and layout the parts for assembly. To better understand these instructions, please refer to the parts drawings found at the back of this manual.
Remove the M12x1.75x60mm Hex Bolt and M12x1.75 Acorn Nut from the Seat Bar. Keeping the Bushings in place, place the Seat Bar in the slot of Seat Collar. Align the holes and reinstall the Hex bolt and Acorn Nut (see Photo 2). Remove the Quick Pin from the rear of the Seat Bar and slide the Seat onto the Seat Bar (see Photo 3). NOTE: The vertical portion of the Seat Bracket is the ‘front’ of the seat. WARNING: FAILURE TO INSTALL THE SEAT PROPERLY COULD CAUSE THE SEAT TO TIP BACKWARDS.
Your R.A.S.S. Bench is now assembled! ADJUSTMENT Your R.A.S.S. Bench is fully adjustable to fit most shooters. The seat height above ground is adjustable. The seat distance from the center post is adjustable. Rifle torso height above the seat is also adjustable. RCBS has found that the seat height adjustment of second from the top to be the most comfortable position for most shooters.
remove it by removing the rear Seat Extension Quick Pin and sliding the Seat off. Remove the front Seat Extension Quick Pin to fold down the Seat and reinstall the Quick Pin in place. Grasping the Handle on the Lower Hub and raising it upward will allow the Legs to fold down on themselves. Secure the Legs with the provided Cinch Strap (see Photo 13). The R.A.S.S. Bench is now ready for transportation to your favorite shooting or hunting spot.
5 4 1 6 3 2 9 7 Item # 1 2 3 4 5 6 7 Part # 9320-105 9320-107 9320-34 180102 180105 180121 187048 Quantity 1 2 1 2 2 1 2 Seat Bar Assembly Description 1/2" x 1.9"L Quick Pin M5x0.8 x 16mm S.H. Cap Screw Adjustable Seat Support Beam Leg Bushing Tube End Cap RUBBER STRIP #10 FLAT WASHER (.203IDx.438ODx.063THK) Item # 1 2 3 4 5 6 7 8 9 Part # 9320-103 9320-104 9320-41 9320-42 9320-43 9320-45 9320-46 180108 Quantity 2 2 1 1 1 1 6 2 1 Seat Assembly Description M10 Nylock Hex Nut M10x1.
15 13 12 14 2 9 6 10 8 7 11 12 12 4 3 1 5 Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part # 9320-103 9320-108 9320-112 9320-115 9320-50 9320-60 9320-65 9320-98 9320-99 180110 180111 180113 180120 180122 180125 Rifle Rest Assembly Quantity Description 2 M10 Nylon Insert Lock Nut 1 M10 x 1.5 x 20 S.H. Cap Screw 1 M6x1 Nylon Insert Lock Nut 1 M6x1 x 30mm Shoulder Bolt 1 Rapid Acquisition Unit 1 Mount Block Assembly 1 Spud Handle 1 Front Clevis Mount 1 Rifle Platform 1 M10x1.
2 3 1 Front Cradle Assembly Part # Quantity Description 9320-73 2 Adjusting Knob 9320-74 1 Front Cradle 180101 1 Acme Rod Item # 1 2 3 Item # 13 3 7 9 10 1 15 12 14 8 6 2 11 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part # 9320-108 9320-109 9320-110 9320-114 9320-116 9320-118 9320-51 9320-52 9320-53 9320-90 180114 180115 180117 180118 180126 Rapid Acquisition Unit Quantity Description 1 M10 x 1.5 x 20 S.H. Cap Screw 1 M4x0.7x30 S.H. Cap Screw 1 M4x0.7x20 S.H. Cap Screw 2 M4x0.
DETACH AND PLACE IN ENVELOPE ____________________________________________________________________________________________________________ Complete all sections Mail to: RCBS Operation R.A.S.S. registration 605 Oro Dam Blvd. Oroville, CA 95965 1. Where Purchased:_______________________________________________________________________ 2. Name: Mr/Ms._________________________________________________________________________ 3.
PRECISIONEERED RELOADING EQUIPMENT We think that we make the very best reloading equipment in the world. If you agree, please tell your friends. If you disagree, tell us we want to do something about it! Customer Service 1-800-533-5000 (US or Canada) or 530-533-5191 Hours: Monday - Thursday, 6:30am - 3:00pm Pacific Time (hours may vary) e-mail: rcbs.tech@atk.com or visit our website at www.rcbs.com RCBS 605 Oro Dam Blvd.