PORTABLE DIGITAL WIRELESS MONITORING SYSTEM INSTRUCTION MANUAL CAMERA: CA670QN FCC ID: SJ8-CA670QN MONITOR:M370M FCC ID: SJ8-M370M
Welcome! Thank you for purchasing the wireless video monitor. Before you start, make sure you have the contents listed below.
Features • Digital wireless technology provides excellent image quality and clarity • Interference free, secure and private signal • Up to 450ft wireless transmission range ① • Listen in with exceptional sound clarity • Two-way audio communication • Safety warning feature notifies you when out of range • System expandable up to 4 cameras ② • Micro SD card recording • Timer Function • USB output for monitoring on PC ① Maximum open space transmission range.
Overview Video Monitor Overview 3
Using the joystick to navigate menus The joystick allows you to navigate through the video monitor menus.
Camera Overview 1). Lens: Camera lens. 2). Microphone: Built-in microphone underneath camera body. 3). PIR Sensor: Passive IR motion sensor for more accurate motion recording. 4). Speaker: Speaker for two-way audio. 5). Night Vision IR: Night vision IR LEDs used for viewing in complete darkness. 6). Pair: Pairing button. For more details, see “Appendix C: Adding Cameras” on page 33. 7). Antenna: Wireless antenna. 8). Power Cable: Connect the included power adapter to the cable extending from the camera.
OSD Overview The video monitor displays the following icons during normal use. The table below summarizes the video monitor icons, and what they mean.
7
Basic Setup Step 1 of 2: Powering on the camera Connect the power adapter to a power outlet and to the camera. Step 2 of 2: Powering on the Video Monitor 1. Connect the power adapter to a power outlet, and to the video monitor directly or charging cradle (ensure the video monitor firmly rests on the cradle). The video monitor’s charging LED indicator glows red to indicate charging is in progress. NOTE: It requires 6 hours to fully charge the rechargeable batteries. 2. Slide the power switch to ON position.
Installing the camera Before you install the camera, plan where and how it will be positioned, and where you will route the cable that connects the camera to the power adapter. • Before starting permanent installation, verify its performance by observing the image on a monitor when camera is positioned in the same location/position where it will be permanently installed. • The cameras are pre-paired so they work out of the box.
Video Monitor Setup Unlocking the video monitor antenna The video monitor has a built-in antenna that improves signal range. It is recommended that you extend antenna for optimal performance. To unlock the monitor antenna: • Slide the lock button to the right. Reading the power indicator LED The power indicator LED glows green when the monitor is powered on. When the battery is low, the power LED blinks.
Pairing Cameras The camera included with the video monitor has already been paired up with the video monitor. If for any reason your monitor and camera are not paired up, or you wish to add additional cameras, follow the directions below. To pair a camera to the video monitor: 1. Place the camera and video monitor 12 inches apart. Turn on the camera first and then the video monitor. 2. Press the Menu button on the monitor, then select Pairing and press the OK button. 3.
Sequence View In sequence view, the monitor switches between up to four cameras every 6 seconds. For example, the monitor displays channel 1 for 6 seconds, then channel 2 for 6 seconds and so on. The monitor only switches to the channels that are paired with a camera. To enable Sequence view: • Press the SEQ/Quad button once to enter sequence mode. To exit Sequence view: • Press the SEQ/Quad button. Quad View You can view all of the paired cameras in quad view.
Using the talk function This system has the feature of two-way audio communication. The talk function allows you to speak into the video monitor, while the camera outputs your voice. The camera also has a built-in microphone, which allows the person to speak into the camera. To use the talk function: 1 Adjust the volume on the camera and video monitor to the desired level. 2 Press and hold the Talk button on the video monitor and begin speaking. Release the Talk button when you are finished.
Using the Scan feature The Scan feature temporarily turns off the video monitor, and waits for a camera to detect a noise. Once one of the cameras detects sounds, the video monitor automatically turns on, and beeps to notify you. This feature is especially useful if you have multiple cameras, and only want to view the camera that detects a sound (i.e. infant crying). To enable the Scan feature: • Press the Scan button. To disable the Scan feature: • Press the Scan button to turn off the Scan feature.
Recording This system is capable of recording video on a microSD card (not included). The video monitor supports microSD cards up to 32GB (gigabytes). Manual Recording Manual recording allows you to record video by pressing the record button on the video monitor. Manual recording may be useful if you want to quickly record an event to your video monitor while you are watching it. NOTE: It is recommended to set the date and time before using the recording function (page 19) To start manual recording: 1.
Viewing recorded files on the video monitor There are two ways that you can view the recorded video files on the microSD memory card: through the video monitor, or on your computer. To view video files through the video monitor: 1. In the mode of live video, press the OK button on the video monitor (press down on the joystick). The File List menu opens. 2. Press OK to open the VIDEO folder. 3. Select the desired folder and press the OK button. NOTE: The folders are named by the year/month/date.
Viewing video files on a PC 1. Remove the memory card from the video monitor. . 2. Insert the microSD card into a memory card reader (not included). NOTE: If required, use a SD card adapter (not included) to convert the microSD card to SD/HCSD memory card format. 3. When the AutoPlay menu appears, click on Open folder to view files. 4. Double-click the VIDEO folder, and then select the desired sub-folder you want to open. NOTE: The folders are named by the year/month/date.
Configuring your video monitor Enabling the Auto Mute feature The Auto Mute feature eliminates white noise when monitoring a room. The Auto Mute feature works by muting the video monitor when the camera detects no audible noise. Once the camera detects a sound, the video monitor unmutes. To enable Auto Mute: 1. Press the Menu button on the video monitor. 2. Select Auto-Mute and press OK. 3. Select ON to enable auto mute. 4. Press the OK button to save your settings.
Changing the date and time 1. Press the Menu button on the video monitor. 2. Select Settings and then press the OK button. 3. Select Date & Time and then press the OK button. 4. Use the joystick to configure the Year/Month/Date/Time. • Press up/down on the joystick to adjust the values. • Press left/right to move between the year, month, date and time. 5. Press the OK button to save your changes. Adjusting the alarm volume The video monitor ’beeps’ when the camera detects audio triggers (i.e.
Adjusting the Timer settings The timer feature allows the video monitor to beep after a set duration as a reminder tool. If the monitor is used as a baby monitor, the Timer tool is useful as a baby feeding timer. To enable the Timer: 1. Press the Menu button on the video monitor. 2. Select Settings and then press the OK button. 3. Select Timer and then press the OK button. 4. Enter the desired time that you want the set the timer at using the joystick. Press left / right to navigate the values.
4. Using the Joystick, press Up/Down to change selection, left/right to adjust the values: • Beside Low Temperature, enter the lowest room temperature threshold. • Beside High Temperature, enter the highest room temperature threshold. 5. Select the ON button and then press the OK button on the joystick. Erasing the memory card Once you erase the memory card, the video will be deleted permanently. To erase the memory card: 1. Press the Menu button on the video monitor. 2.
Trouble Shooting 22
Specifications Receiver Receiving Frequency Range 2400 ~ 2483.5MHz Display Size 3.5” TFT LCD Power Requirement 5V DC 1A Battery Voltage 3.7V Li-Polymer Battery (built-in) Battery Lift 4.5 hours Operating Temp Range 14°F ~ 100°F (-10° ~ 40° C) Operating Humidity 0 ~ 85% RH Camera(s) Transmit Frequency Range 2400 ~ 2483.
Notices FCC Notice This device complies with Part 15, subpart C, of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
