Model 24921 Owner’s/Installation Guide
Congratulations Congratulations and thank you for purchasing one of our state-of-the-art remote start systems. Directed is the world leader in vehicle security, remote start, and keyless entry systems, so yes, you have made the right choice! STOP! Read this First Please make sure you follow all the steps listed below before attempting to install this system in your vehicle. Step 1: Watch the instructional DVD included with this system. Step 2: Read this guide from cover to cover. Step 3: Register at www.
What's Included • • • • • • • • • • • • Control Module One 1- Button Remote Control Control Button (Valet Switch) Antenna and Cable Harnesses Hood Pin Switch Hardware Kit Neutral Safety Switch Bypass Module (24921B only) Your Warranty Registration Card DVD - Do-It-Yourself Installation Video This Guide Tools Required • • • • • • • • • • Digital Multi-Meter Drill 1/4 Drill Bit (for hood pin switch) Screwdrivers (Phillips and Flathead) Wire Stripper Solder Iron Electrical Tape Pliers Crimping Tool Safety G
Important Information Government Regulations and Safety Information Read the Government Regulations and Warning! Safety First sections of this guide prior to operating this system. Warning! Failure to heed this information can result in death, personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose. Your Warranty Your system comes with a warranty. Your product warranty must be validated following your purchase. You can validate online at: www.
Guide Translations If you want a Spanish or French version of the Installation/Owners Guide, please download it from www.readyremote.com and click on On-Line Tech Support. Estimado Cliente: Si buscas los guías de instalación/del usario, por favor de bajar lo del Soporte Técnico en-línea en el sitio www.readyremote.com Cher consommateur: Si vous désirez une version française ou espagnole du guide d’utilisateur ou d’installation, veuillez s.v.p. le télécharger à l’adresse suivante: www.readyremote.
Contents Congratulations................................................................................................ iii STOP! Read this First......................................................................................... iii What's Included ............................................................................................ iv Tools Required.................................................................................................. iv Important Information.......................
Installation Guide Wiring Schematic Antenna Parking Light Jumper Side View Side View LED (Pro indicato Top View Control (Valet S H2 avy uge elay Antenn H1 Primary Harness Antenna Parking Light Jumper Side View H3 Auxiliary Harness Antenna Parking Light Jumper Side View LED (Programming Top View indicator) Top View H2 Heavy Gauge Relay Control Button (Valet Switch) Antenna H1 Primary Harness 2 H3 Auxiliary Harness H1 Primary Harness H3 Auxiliary Harness © 2010 Directed Electronics.
Wiring Connections Primary Harness (H1), 9-pin connector H1/1 LIGHT GREEN BLACK (-) 200mA FACTORY ALARM DISARM H1/2 GREEN/WHITE (-) 200mA FACTORY ALARM REARM H1/3 EMPTY NOT USED H1/4 WHITE/BLUE (-) ACTIVATION INPUT H1/5 EMPTY NOT USED H1/6 EMPTY NOT USED H1/7 EMPTY NOT USED H1/8 BLACK GROUND H1/9 WHITE (+/-) LIGHT FLASH OUTPUT Heavy Gauge Relay Harness (H2), 6-pin connector H2/1 PINK OUTPUT TO PRIMARY IGNITION CIRCUIT, 30A (+) H2/2 PURPLE OUTPUT TO STARTER CIRCUIT, 30A (+) H
Control Button (valet switch), 2-pin connector 1 BLACK INPUT 2 GREY OUTPUT Installation Points Note: The LED referenced within the installation section is the LED (programming indicator) on the Control Module unless otherwise stated. Virtual Tach Note: Use of Virtual Tach does not require the Tach wire to be connected. To program Virtual Tach: 1. After the install is complete, remote start the engine. The programming operation may require 3 cranks of the starter before the engine starts and runs.
Tach Learning Note: Tach learning requires H3/2 (Violet/White) wire to be connected to Tach. If using Virtual Tach, this procedure is not required and should not be used. To learn the tach signal: 1. Start the vehicle with the key. 2. Within 5 seconds, press and hold the Control button. 3. After 3 seconds the LED will light constant when the tach signal is learned. 4. Release the Control button.
tory default settings. Note: This feature does not delete the remote controls from the system or reset the Virtual Tach setting 3. 4. Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on the next remote start sequence the unit begins virtual tach initialization. Once you have selected the function step, press the Control button once more and hold it. The LED flashes to confirm the selected functional step.
4 5 6 7 8 flashes flashes flashes flashes flashes Transmitter shutdown (or optional push button) (-) Hood Shutdown (H3/4 Gray) (+) Brake Shutdown (H3/3 Brown) (-) Neutral safety shutdown (H3/1 Black/White) Wait-to-start timed out Programming System Features The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the feature settings (see Feature Menu) using the Control button. 1. Turn the ignition on, then off. 2.
The learn routine exits if any of the following occurs: • The ignition is turned On • There is no activity for 30 seconds • The Control button is pressed too many times 8 © 2010 Directed Electronics. All rights reserved.
Feature Menu Default settings are in bold type. Feature # Feature Opt. 1 Opt. 2 Opt. 3-5+ 1 Engine checking Virtual tach voltage (3) Off, (4) Tachometer 2 Remote Start Engine Runtime 12 min 24 min 60 min 3 Park light output Pulsed Constant 4 Cranking time 0.6 sec. 0.8 sec. (3) 1.0 sec. (4) 1.2 sec. (5+) 1.4, 1.6, 1.8, 2.0, 4.0 sec.
Remote Control Programming 1. 2. 3. 4. 5. 6. 7. Turn key to the ON position Within 5 seconds, press and release Control button one time. Within 5 seconds, press and hold the Control button. The LED will flash one time to confirm entry into remote programming. Press the button on the remote control. The LED flashes to confirm the remote has been programmed. Release the Control button, and turn the key to the Off position. The LED turns on solid for a while to confirm that remote programming has been exited.
Owner's Guide System Maintenance The system requires no specific maintenance beyond battery replacement for the remote control. Your remote is powered by a coin cell battery (3V CR2032) that lasts approximately one year under normal use. When the battery begins to weaken operating range is reduced. Battery Replacement Locate the small slot on the side of the remote control. Insert a small slotted screwdriver or equivalent tool into slot and pry the case apart.
Sirius Warning! (1) Never remote start your vehicle when the keys are in the ignition, except when performing Valet Take-Over, and (2) Never start the vehicle if it is not in PARK or NEUTRAL To remote start the vehicle: • Press the button on the remote control once (default)*. • The parking lights flash to confirm that the vehicle is attempting to start.
the engine will shut down. While the vehicle is running during remote start operation, the system monitors the vehicle and automatically shuts down the engine if it receives any of the following shut-down inputs: • • • • • The brake pedal is pressed. The hood is opened. The shutdown toggle switch is put into the Off position. The pre-programmed run time has elapsed. Remote control button is pressed and held for 3 seconds.
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
Warning! Safety First The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must be done properly according to instructions with safety always considered. Failure to properly install this system and its safety features may result in personal injury, property damage or both. When properly installed, this system can start the vehicle via a command signal from the remote control.
outlined in this guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.
2. 3. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start system. The vehicle should not start. If the starter engages, check your hood pin and connections. Note: If programmed for Diesel Mode, the system will turn on the ignition, but the starter should not engage with the hood open. Test the NEUTRAL SAFETY shutdown circuit: Important: Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test. a. b. c.
Patent Information This product is covered by one or more of the following U.S.
Lifetime Consumer Warranty For a period of one calendar year from the date of purchase of this auto-security, remote start or keyless entry device, as applicable (hereinafter “Unit”), Directed Electronics (“Directed”) promises to the ORIGINAL PURCHASER to repair or replace (at Directed’s election) with a comparable, reconditioned Directed DIY Unit (excluding without limitation, the siren, remote transmitters and associated sensors and accessories) which proves to be defective in workmanship or material unde
Consumer’s remedy is limited to repair or replacement of the Unit, and in no event shall Directed’s liability exceed the purchase price of the Unit.
The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, DIRECTED is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.