User Guide
Surface Preparation
The durability and final cosmetic outcome
of Ready Seal® coatings may be impaired
by a poorly prepared or unsound surface.
Surfaces must be clean of mildew, dust,
dirt, oil, grease and any other foreign
matter.
All previous stains and sealers must be
completely removed.
Any caustic strippers or cleaners must
be neutralized.
Wood must contain moisture content of
12% or less.
New, unseasoned wood must be allowed
to weather sufficiently before properly
accepting coatings of Ready Seal®.
Before application, protect and/or mask
all plants and surfaces not to be sealed.
Application Process
Shake and/or stir stain thoroughly prior
to application.
Inter-mix all containers of the same
color to insure color uniformity.
Always test stain in a small area to
ensure satisfaction with color and
appearance.
Apply with a brush, roller, pump sprayer
or airless spray unit.
Apply one generous coat or two light
coats with at least 45 minutes between
coats. No back-brushing is necessary.
Allow 48 to 72 hours of drying time (at
75°F 65% relative humidity). Drying
time will vary depending on
temperature, porosity of surface and
humidity.
Ready Seal® is darker when first
applied and reaches its true color in 7-10
days.
Physical and Chemical Hazards
Combustible: Do not use or store near
heat source or open flame.
In case of fire: Use dry chemicals,
foam, water fog, or carbon dioxide
extinguisher.
Spills, leaks and disposal: Absorb into
inert material and dispose of
according to federal, state and local
regulations.
Environmental
This product is toxic to fish. Do not
apply directly to water or areas where
surface water is present or to intertidal
areas below the mean high water
mark. Do not contaminate water when
disposing of hazardous waste.
Precautions
Do not apply this product in a way
that will come in contact with any
person or pet. Do not use on wood
that will come in contact with food.
Apply this product only as specified
on the label. Keep container sealed
when not in use. Always wear
goggles, rubber gloves, protective
clothing and a NIOSH/MSHA
approved respirator when applying or
treating lumber. Use in well-ventilated
area. Keep contents away from food
and living plants.
Caution
Causes moderate eye irritation.
Harmful if swallowed, absorbed
through skin or inhaled. Avoid contact
with eyes or clothing. Prolonged
exposure to vapors may cause nasal
and respiratory irritation. Use only in
well ventilated areas. Wash exposed
skin areas with soap and water. Do not
take internally.
Ready Seal® Stain Technical Data Sheet
Technical Specifications
Weight per gallon:
7.5 +/- .01 lbs.
Solids by weight:
81-85%
Solids by volume:
65-69%
VOC content:
Less than 100 grams/liter. Meets
Federal and all State VOC
requirements.
Temperature limits:
N/A. Cooler temperatures prolong
dry time. Direct sunlight poses no
application issues.
Moisture Levels:
Surfaces to be sealed must
contain moisture content of 12%
or less.
Limitations
Life expectancy on vertical
surfaces is 2-5 years and 1-3
years on horizontal surfaces.
The ability of this product
to perform is dependent
upon proper surface
preparation and correct
application. This product
must penetrate the wood’s
surface to work properly.
Incorrect preparation and/or
application may result in
shortened life. For optimal
performance and as
preventative maintenance,
clean and recoat surfaces
every two years.
Limited Warranty
Ready Seal® guarantees the quality of contents of every container. Ready Seal® has no control over surface
preparation or application techniques. No guarantee as the results are offered, expressed or implied. If the
product is found to be defective, replacement material may be furnished free of charge; or a refund of the
material cost may be issued at manufacturer’s option. Labor costs are not covered by this warranty.
Responsibility for claims of any kind is strictly limited to the purchase price of the material.