Use and Care Manual

READY-STRIP ADVANCED
SAFER PAINT & VARNISH REMOVER-NMP FREE
TECHNICAL DATA SHEET
I. Description: Ready-Strip Advanced is a one of a kind,
environmentally friendly, paint and varnish remover capable of
removing up to 7 layers in a single application using a stripping
tool. The revolutionary "Color Change" feature signals the time
for paint removal. The stripper is applied to the surface and
turns off-white or a pale green when the paint or varnish is
READY to be removed. Ready-Strip Advanced is non-
flammable, biodegradable, virtually odorless and can be
cleaned up with water. It does not contain methylene chloride,
NMP, caustic, flammable chemicals or harmful vapors like many
traditional strippers. Ready-Strip Advanced avoids the
uncertainty associated with other strippers that are ineffective if
removed too soon, or dry out and not work if left on too long.
Ready-Strip Advanced eliminates the guesswork. Unlike
other strippers, Ready-Strip Advanced is a semi-paste and
therefore truly clings to vertical surfaces.
II. Types of Paint Removed: Ready-Strip Advanced can
remove most varieties of household paints & varnishes which
are water or oil-based including, latex, stains, enamels,
lacquers, clear paints as well as polyurethanes, etc.
III. Surfaces: Ready-Strip Advanced can be applied on a
multitude of interior and exterior surfaces including wood,
plaster, concrete, brick, stone, masonry, marble, metal and
fiberglass, etc. Ready-Strip Advanced will not damage plaster
or wood (discolor or raise the grain) or affect any surface it is
used on. Ready-Strip Advanced is not to be used on sheetrock,
plastic, rubber or linoleum surfaces.
IV. Instructions:
A. TEST PATCH - Since it is often hard to know the
type or amount of paint or varnish on a surface, a small test
area should be tested first to determine whether the desired
results will be achieved.
B. Preparation- Mask any areas not being stripped
with plastic and masking tape.
C. Application and Removal- Apply Ready-Strip
Advanced liberally to the surface with a brush, medium sized
nap paint roller, or putty knife so that the remover completely
"masks" or covers the color of the surface to be stripped. Do
not attempt to brush out too thin like a coat of paint. It
covers approximately 50 sq. ft. per gallon. Apply at
temperatures between 60
0
F and 80
0
F. When the stripper
turns off-white or a pale green, it may form an eggshell like skin
to lock in the stripping action. Misting the area to be removed
with water or BTN Ready Strip Paint Overspray Remover prior
to actual removal will soften the skin and make lifting of the
paint or varnish easier. After the stripper has turned off-white or
a pale green, use a stiff putty knife to lift paint from flat surfaces
or a stiff bristle brush for detailed areas. After initial lifting, use
a nylon bristle brush or stripping pad to scrub surface. The time
the stripper takes to turn off-white or pale green may vary
depending upon the type and amount of paint, the surface and
temperature. . Typical color change usually occurs within 4 - 24
hours. Paint or varnish removal may take place prior to the
“Color Change”, although the “Color Change” will indicate the
end of stripping action. Apply Ready Strip Paint Overspray or
light amounts of water for final clean up of residue. Surface
should be completely dry before repainting. No need to
neutralize (acid wash) surface. Clean tools promptly after use
with soap and water.
D. Removal Time - On interior surfaces, the softened
paint/varnish may remain moist under the eggshell skin for
several days for easy removal. On exterior surfaces, due to the
potential for higher temperatures and direct sunlight, the “Color
Change” may be greatly accelerated (1–8 hours). The paint
should be removed shortly after “Color Change” to prevent the
stripper from drying out. Not advisable for outdoor decks
E. Hints – If Ready-Strip Advanced is applied too
thinly, left on too long, or due to excessive heat conditions, the
applied area is difficult to scrape, try the following: 1) Mist the
applied area with water or After-Strip, wait 5-15 minutes and
remove; 2) Reapply Ready-Strip Advanced over itself, wait 15-
30 minutes and remove; 3) if 1) or 2) does not work, scrape off
and reapply.
If product freezes in bucket, let thaw and stir vigorously until
product is consistent.
V. Safety Instructions: Due to the sensitive nature of certain
person's skin, rubber gloves and safety glasses are
recommended. Avoid eye contact. If eye contact occurs
immediately flush with plenty of water for 15 minutes. Avoid
prolonged and repeated contact with skin. If skin contact
occurs, wash with soap and water. Maintain adequate
ventilation especially in confined areas. If spraying is expected
use NIOSH approved chemical cartridge (organic vapor)
respirators. If swallowed do not induce vomiting. Give 1 or 2
glasses of water and call a physician immediately.
SUNNYSIDE CORPORATION 225 CARPENTER AVENUE WHEELING, IL 60090 PH: 847-541-5700 FAX: [phone]