Spec Sheet 1

ManualsBrandsReal Fyre ManualsFireplace/Gas Stove AccessoriesVented Collection BTA-24 24" Burnt Aspen Log with Stainless Steel Booster Grid Acts, Unique Fiber and Protective Bark-Textured Cover

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

LOG SET IMPORTANT INFORMATION

L-A2-443REV 2 - 1904241035

BURNT ASPEN LOG PLACEMENT INSTRUCTIONS

BTA-30 shown

This log set is to be installed along with

the booster grid, glowing embers (B), and

bryte coals that are supplied with your

G52 burner system. Refer to the parts list

in the main owner's manual.

Important: Adequate ventilation is absolutely

necessary. Adequate spacing

between the logs is NECESSARY

and MUST be maintained. Some

carbon build up (sooting) may occur

where ﬂ ames strike the logs. If carbon

build up (sooting) continues, rearrange

top logs to allow more opening(s) for

ﬂ ame(s) before sooting becomes worse.

If any sooting occurs outside of the

ﬁ rebox (i.e. on the walls), turn off unit

immediately and contact a qualiﬁ ed

professional service technician.

This product is only warranted when used as part of

a Robert H. Peterson Co. vented burner system.

CAUTION...............WARNING...............IMPORTANT

USE ONLY A PETERSON REAL FYRE G52 BURNER WITH THIS REAL FYRE LOG SET.

WARNING: Use ONLY a Peterson Real Fyre

G52 burner with this Real Fyre gas log

set. Failure to do so may result in

property damage or personal injury,

and will void listings, certiﬁ cations,

and invalidate claims made to RHP.

Contact your local Real Fyre dealer if you

need more information.

This instruction contains log set, booster grid, and ember placement for these Real Fyre logs. You

must position and maintain the log layout as shown here to ensure proper operation of the burner

system. Use these logs only with a Peterson G52 burner system.

Adequate ventilation is absolutely necessary! Provided signiﬁ cant, noticeable sooting does not occur,

some ﬂ exibility is possible in top log placement to suit your individual preference (see Important below). If

you experience a continued accumulation of black carbon (soot) on your logs it is an indication of incomplete

combustion and you should move the effected log(s) so as to minimize the ﬂ ame contact on the effected

log(s). If signiﬁ cant sooting continues, stop using this gas log set.

Please read these instructions completely and carefully.

Standard burner model shown

here. Stainless steel models have

the same placement.

Summary of content (6 pages)

PAGE 1
BURNT ASPEN LOG PLACEMENT INSTRUCTIONS CAUTION...............WARNING...............IMPORTANT USE ONLY A PETERSON REAL FYRE G52 BURNER WITH THIS REAL FYRE LOG SET. This log set is to be installed along with the booster grid, glowing embers (B), and bryte coals that are supplied with your G52 burner system. Refer to the parts list in the main owner's manual. BTA-30 shown Standard burner model shown here. Stainless steel models have the same placement.
PAGE 2
Note: The conditions/environment of each setup will slightly vary. After installation of your unit is complete, follow the LIGHTING INSTRUCTIONS section to light the burner. The burner system will reach optimal performance and appearance after approximately 20 minutes. WARNING: This gas log set is for use with an R.H. Peterson Co. G52 burner (and parts) ONLY. CAUTION: Burn hazard! Logs will remain hot for some time after use.
PAGE 3
BURNT ASPEN LOG PLACEMENT INSTRUCTIONS BEGIN WITH THE GENERIC LOG, BOOSTER GRID, AND EMBER STEPS BELOW, THEN LOCATE THE PAGE FOR YOUR LOG SET SIZE CHOSEN TO COMPLETE PLACEMENT. Generic Placement Steps All models begin with the bottom log and ember placement shown below. To complete log placement continue to the appropriate section (on one of the following pages) specific to your log set size.
PAGE 4
BURNT ASPEN LOG PLACEMENT INSTRUCTIONS Generic Placement Steps (cont.) 1B 1C Grid "C" facing forward Grid within notches/tabs Place remaining embers B as shown Radiant booster grid detail: • Place the remaining amount of embers B across the grid as shown. Rest against rear log, orient with grid "C" facing forward, and within notches/tabs. 2A 2 2 Gently bring together the rear and front logs to create a tight fit around the grid. Place the left and right front log pieces (log #2) as shown.
PAGE 5
BURNT ASPEN LOG PLACEMENT INSTRUCTIONS (18" MODEL) For 18" log sets, continue with the steps below to complete placement. BTA-18 CAUTION: Burn hazard! Logs will remain hot for some time after use. PARTS LIST BTAL-10 6 All items for this log set are included in one (1) box. BTAL-12 * 5 4 BTAL-14 3 I BTAL-13 1 2 Refer to pages 3-4 for details on proper bottom log, booster grid, and ember placement. * 3 BTAL-16BR BTAL-18BF Place the center log (log #3) as shown.
PAGE 6
BURNT ASPEN LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS) For 24" and 30" log sets, continue with the steps below to complete placement. BTA-24 & BTA-30 CAUTION: Burn hazard! Logs will remain hot for some time after use. PARTS LIST 8 7 24"- BTAL-11 30"- BTAL-12Y BTAL-8 All items for this log set are included in one (1) box. * 6 5 Refer to pages 3-4 for details on proper bottom log, booster grid, and ember placement.