Spec Sheet 1

ManualsBrandsReal Fyre ManualsFireplace/Gas Stove AccessoriesEPK-2VP-TR Electronic Pilot Valve Kit with Variable Frame Height Control, Flame Sensing Pilot and Remote Control in Black

L-A2-376

Rev 1 - 1904120815

Important: Read these instructions carefully

before starting installation of the

burner control system.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, California 91746

INSTALLATION &

OWNER’S MANUAL

The Peterson Real-Fyre

burner system is to be

installed only in a solid-fuel-burning ﬁreplace with a

working ﬂue constructed of noncombustible material.

Solid fuels shall not be burned in a ﬁreplace where the

unit is installed. The installation, including provisions

for combustion, ventilation air, and required minimum

permanent vent opening, must conform with the

National Fuel Gas Code (ANSI Z223.1/NFPA 54)

and applicable local building codes. In Canada, the

installation must conform with the Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B-149.1). A damper stop clamp is included to

maintain the minimum permanent vent opening and to

prevent full closure of the damper blade. The chimney

damper must be ﬁxed fully opened when burning

the unit. The burner system is designed to burn

with yellow ﬂames; thus, adequate ventilation is

absolutely necessary.

INSTALLER & CONSUMER

These instructions MUST be

retained with this appliance

Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier from

a neighbor’s phone and follow the gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁre department.

WARNING

If the information in this manual is not followed

exactly, a ﬁre or explosion may result, causing

property damage, personal injury, or loss of life.

Installation and service must be

performed by an NFI Certiﬁed or other

qualiﬁed professional installer, service

agency, or the gas supplier.

EPK-2V/3V-TR PILOT KITS

(Suitable for G4 and G45 series burners)

• INTERMITTENT SPARK

IGNITION PILOT

• REMOTE OR MANUAL

OPERATION

• AC POWER OPERATION

• VARIABLE FLAME

HEIGHT CONTROL

2V model shown

Models:

EPK-2V(P)-TR

EPK-3V(P)-TR

Summary of content (18 pages)

PAGE 1
INSTALLATION & OWNER’S MANUAL • INTERMITTENT SPARK IGNITION PILOT Models: EPK-2V(P)-TR EPK-3V(P)-TR • REMOTE OR MANUAL OPERATION • AC POWER OPERATION 2V model shown • VARIABLE FLAME HEIGHT CONTROL (Suitable for G4 and G45 series burners) EPK-2V/3V-TR PILOT KITS Important: Read these instructions carefully before starting installation of the burner control system.
PAGE 2
TABLE OF CONTENTS GETTING STARTED IMPORTANT INFORMATION �� 3 ELECTRICAL SAFETY INFORMATION �� 4 SPECIFICATIONS �� 4 REPLACEMENT PARTS LIST - 2V MODEL ��
PAGE 3
IMPORTANT INFORMATION CHECK TO BE SURE THAT THE PROPER FUEL GAS IS BEING USED WITH THIS PILOT KIT. The installation, including provisions for combustion and ventilation air, must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code (ANSI Z223.1/NFPA 54). This component and its individual shutoff valve must be disconnected from the gas-supply piping system when testing at pressures that exceed 1/2 psig. This is accomplished by closing the gas-supply line valve.
PAGE 4
ELECTRICAL SAFETY INFORMATION • To protect against electric shock, do not immerse cord or plugs in water or other liquid. • Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts. • Do not operate with a damaged cord, plug, or after the appliance malfunctions or has been damaged in any manner. Contact the manufacturer for repair. • Do not let the cord touch hot surfaces. • Do not use for purposes other than intended.
PAGE 5
REPLACEMENT PARTS LIST - 2V MODEL DO NOT REMOVE THE PILOT/IGNITER ASSEMBLY FROM THE VALVE OR IGNITER PACK. 2 1 Note: Photos not to scale 5 9 ON ON AUTO TIMER HI/LO OFF 8 3 7 4 6 Item Description Rev 1 - 1904120815 Part No. Qty. PAC-11 1 PAC-11P 1 1. Pilot/igniter assembly (natural) or Pilot/igniter assembly (propane) 2. Pilot mounting bracket kit PB-51 1 3. Control valve w/ wire harness (Nat.) SV-49 1 or Control valve w/ wire harness (L.P.) SV-49P 1 4.
PAGE 6
REPLACEMENT PARTS LIST - 3V MODEL DO NOT REMOVE THE PILOT/IGNITER ASSEMBLY FROM THE VALVE OR IGNITER PACK. 1 5 ON ON AUTO TIMER HI/LO OFF 9 2 7 8 3 4 6 Note: Photos not to scale Item Description Rev 1 - 1904120815 Part No. Qty. PAC-11 1 PAC-11P 1 1. Pilot/igniter assembly (natural) or Pilot/igniter assembly (propane) 2. Pilot mounting bracket kit PB-51 1 3. Control valve w/ wire harness (Nat.) SV-48 1 or Control valve w/ wire harness (L.P.) SV-48P 1 4.
PAGE 7
INSTALLATION This safety pilot system must be installed by a qualified professional service technician. Instructions must be followed carefully when installing to ensure proper performance and full benefit from the burner system and safety pilot system. These instructions must be used as a supplement to the instructions supplied with the R.H. Peterson burner system. Follow the burner system instructions and make adjustments as appropriate for the addition of a safety pilot system.
PAGE 8
INSTALLATION (Cont.) INSTALL THE FLAME DIVERTER BRACKET (Valve not shown) For installation on G4/G45 burners only. When properly installed onto the burner pan, the flame diverter bracket will promote quicker ignition and protect the safety control system from overheating. 1 2- /4" Burner pan Note: You must first install the flame diverter bracket before installing the pilot/igniter assembly . 1.
PAGE 9
INSTALLATION (Cont.) CONNECT TO GAS SUPPLY To connect the valve to the gas supply, the flex connector kit and component parts will be needed, which are included with the burner system. Refer to the PARTS LIST in the instructions supplied with the burner to identify the key parts needed. Attach the flex connector to the elbow on the valve (rear view of valve) 1. MAKE SURE THE FIREPLACE GAS SUPPLY IS TURNED OFF. 2. Locate the gas-supply stub inside the fireplace and remove the cap, if attached.
PAGE 10
INSTALLATION (Cont.) CHECKING THE CONTROL MODULE The valve system comes completely assembled with the wiring harness already connected. However, we recommend that you follow the steps below to ensure it has not become detached during shipping before connecting to the power supply. Check connections TO CHECK THE WIRING ASSEMBLY "I" wire 2.
PAGE 11
INSTALLATION (Cont.) CONNECT TO A POWER SUPPLY Receptacle MUST be: 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire Locate the supplied power supply and connect it to the ignition module pack. Then route it to the previously wired 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire receptacle and connect (see Fig. 11-1). INSTALL/REPLACE REMOTE TRANSMITTER BATTERIES CAUTION: Ensure the unit is connected to the gas line and has been tested for leaks before you insert batteries.
PAGE 12
NOTES PAGE Please use this page to record any information that you may want to have at hand.
PAGE 13
LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device that automatically lights the pilot. DO NOT attempt to light the pilot by hand. B. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
PAGE 14
LIGHTING INSTRUCTIONS (cont.) MANUAL LIGHTING CAUTION: DO NOT attempt to light the pilot by hand. The remote receiver will emit an audible "beep"; then the igniter will begin to spark. After the pilot lights and is established, the valve will automatically open and the burner will light. Note: The ignition sequence will take approximately 5 seconds. WARNING: If the pilot fails to light within 10 seconds, turn OFF the system.
PAGE 15
REMOTE OPERATING INSTRUCTIONS ORIENTATION Prior to remote transmitter use, light the appliance per the REMOTE LIGHTING section. The remote will only operate the burner system in remote mode. Familiarize yourself with the transmitter keys and display, as illustrated in Fig. 15-1 and Fig. 15-2. Identify the four transmitter keys: • ON/OFF KEYS: These keys turn the system ON or OFF.
PAGE 16
TROUBLESHOOTING PROBLEM 1. Pilot will not light CAUSE SOLUTION a. Obstruction in pilot gas supply or pilot gas-supply line is kinked a. Clear out obstruction. Replace pilot gassupply line if kinked b. Inadequate gas supply b. Have gas pressure checked by installer or gas supplier c. Air in line d. Gas is shut off on control valve (3V models only) 2. No spark at pilot c. Air should clear; attempt to relight d. Turn on valve (3V models only) a. Loose wires a.
PAGE 17
ELECTRONIC PILOT TROUBLESHOOTING Detail A Electrode (A) When adjusting the spark electrode (if necessary); NEVER adjust the electrode by bending the wire. ALWAYS adjust the electrode by loosening the retainer nut(s), then adjust accordingly. The minimum gap between the spark electrode/ heat sensor and the pilot flame hood is 1/8". The maximum is 5/32". Hood Spark electrode Electrode Ceramic Threaded barrel 1/8" min. gap Heat sensor 1/8" min. gap Fig.
PAGE 18
WARRANTY PETERSON VENTED DECORATIVE GAS APPLIANCE LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Real Fyre® vented decorative gas appliance to be free from defects in material and workmanship. Peterson vented ceramic refractory gas logs are warranted for as long as you own them (lifetime). Peterson vented burner assemblies are WARRANTED for TEN (10) YEARS. Peterson glass, gems, nuggets, and fiber-ceramic blend gas logs are warranted for FIVE (5) YEARS.