Spec Sheet 1

ManualsBrandsReal Fyre ManualsFireplace/Gas Stove AccessoriesVent-Free Collection G10-24/30-SS 24" and 30" Unvented Burner with Electronic Ignition System, Bryte Coals and Pre Assembled Control Valve in Silver Color

OWNER’S

MANUAL

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

Important

Read these instructions carefully and completely

before starting installation of the burner system.

This is an UNVENTED gas-fired heater. It

uses air (oxygen) from the room in which it is

installed. Provisions for adequate combustion

and ventilation air MUST be provided. See

section entitled VENTILATION AND CONFINED

SPACE INFORMATION.

This appliance is designed as an attended

appliance. Adults must be present when the unit

is operating. Do not leave this unit burning when

unattended or while anyone is sleeping.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference

WARNING: If the information in this

manual is not followed exactly, a ﬁ re or

explosion may result, causing property

damage, personal injury, or loss of life.

Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the ﬁ re department.

G10 UNVENTED GAS LOG SETS

Installation and service must be performed by

a qualiﬁ ed professional service technician,

service agency, or the gas supplier.

This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home where not

prohibited by local codes.

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gasses.

Standard and Stainless

Steel Burner Systems:

G10-**(P) (-SS)

G10-**-01V(P) (-SS)

G10-**-12(M)(P) (-SS)

G10-**-15(M)(P) (-SS)

**Sizes:

(16/18, 24/30)

It is imperative that you maintain

your unvented gas appliance by

having it cleaned and serviced

regularly. See pages 11, 31-34 for

details.

L-F2-057

REV 10 - 1810031135

Installation, service, and the provisions for combustion

and ventilation air MUST conform with local codes

and with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the CSA B149.1, Natural Gas And

Propane Installation Code.

DESIGN CERTIFIED

to standards:

Unvented Room Heater

ANSI Z21.11.2

and

Vented Decorative Appliance

ANSI Z21.60

Summary of content (34 pages)

PAGE 1
OWNER’S MANUAL DESIGN CERTIFIED Standard and Stainless Steel Burner Systems: to standards: Unvented Room Heater ANSI Z21.11.2 and Vented Decorative Appliance ANSI Z21.60 G10-**(P)(-SS) G10-**-01V(P)(-SS) G10-**-12(M)(P)(-SS) G10-**-15(M)(P)(-SS) **Sizes: (16/18, 24/30) G10 UNVENTED GAS LOG SETS Important Read these instructions carefully and completely before starting installation of the burner system.
PAGE 2
CONTENTS GETTING STARTED SPECIFICATIONS AND REQUIREMENTS ...................................................................................................... 3 IMPORTANT SAFETY INFORMATION ........................................................................................................... 4 VENTILATION AND CONFINED SPACE SAFETY INFORMATION ................................................................ 5 MINIMUM CLEARANCES TO COMBUSTIBLES ...........................................................
PAGE 3
SPECIFICATIONS AND REQUIREMENTS WARNING: This appliance is for installation only in a: 1. Solid-fuel-burning masonry or UL-127 factory-built fireplace, or 2. Listed ventless firebox enclosure. Rear width It has been designed certified for these installations. Exception: DO NOT install this appliance in a factory built fireplace that includes instructions stating it has not been tested or should not be used with unvented burner systems.
PAGE 4
IMPORTANT SAFETY INFORMATION UNVENTED ROOM HEATER GENERAL SAFETY INFORMATION A. WARNING: CARBON MONOXIDE POISONING MAY LEAD TO DEATH. Early signs of carbon monoxide poisoning are similar to the flu, with headaches, dizziness, and/or nausea. If you have these signs, the gas appliance may not be installed correctly, or may not be working properly.
PAGE 5
VENTILATION AND CONFINED SPACE SAFETY INFORMATION Your vent-free gas burner system SHALL NOT BE INSTALLED IN A CONFINED SPACE or unusually tight construction unless provisions are made for adequate combustion and ventilation air. • The National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines a confined space as a space whose volume is less than 50 cu. ft. per 1,000 BTU per hour (4.8 meters 3 per kw) of the aggregate input rating of all appliances installed in that space.
PAGE 6
MINIMUM CLEARANCES TO COMBUSTIBLES If the vent-free burner system is installed in a factory built fireplace, follow the manufacturer’s guidelines for minimum clearances to combustibles. In the absence of such guidelines, follow the instructions below: Because of these variables, we cannot guarantee that heat warping or discoloration will never occur. The potential for heat warping or discoloration may exist no matter what item(s) you are burning in the fireplace, including wood.
PAGE 7
MINIMUM CLEARANCES TO COMBUSTIBLES (Cont.) IF YOU CANNOT MEET THESE MINIMUM CLEARANCES, YOU MUST OPERATE THE VENT-FREE GAS BURNER SYSTEM WITH THE CHIMNEY FLUE DAMPER OPEN. Mantel clearance with hood * Mantel clearance without hood * Standard Fireplace Hood with minimum 4" horizontal projection 14" 12" 10" 8" 6" 2.5" 34" 32" 30" 28" 14" 12" 10" 8" 6" 2.5" 1.5" Horizontal projection from face of fireplace 25" .
PAGE 8
PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY CAUTION: Installation and repair must be done by an NFI certified or other qualified professional installer. Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand all safety precautions and warnings contained in this manual. PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY GUIDELINES A.
PAGE 9
INSTALLATION SAFETY INFORMATION INSTALLATION SAFETY GUIDELINES A. Carefully inspect the burner and log cartons for shipping damage. If any parts are missing/damaged, call your dealer. Do not attempt to install the appliance unless all parts are in good condition. B. Correct installation of the glass or the ceramic refractory log set and proper placement and installation of the burner assembly, including ember placement and Lava Granule placement, are imperative to safe operation of your set.
PAGE 10
OPERATIONAL SAFETY INFORMATION OPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLY A. SOLID FUEL MUST NOT BE BURNED in a fireplace where this vent-free gas appliance is installed. B. GLASS DOORS MUST BE FULLY OPEN when this vent-free gas appliance is operating. This appliance MUST NOT BE ON if glass doors are closed, as it can lead to sooting, burner outages, and possibly explosion, causing damage or injury. C. WARNING: DO NOT ALLOW DRAFTS INTO OR AROUND THE FIREPLACE.
PAGE 11
OPERATIONAL SAFETY INFORMATION (Cont.) OPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLY N. This appliance is intended for supplemental heating, and is not a primary heating source. Water vapor produced by vent-free burner systems can create moisture problems in a home when operated for extended periods of time. If condensation begins to occur, open your damper or a window. O.
PAGE 12
G10 BURNER REPLACEMENT LIST - MANUAL SERIES Note: Photos not to scale 1 5 ODS pilot assembly 4 2 8 7 24/30" model shown Standard model shown here. Burner system is also available in stainless steel. 6 9 Replacement parts can be ordered from your local Real Fyre dealer. The log set is purchased and packaged separately; contact your local dealer when ordering. Refer to the instructions included with the log set. 16/18" model 24/30" model Description Part No. Qty. Part No. Qty. 1.
PAGE 13
G10 BURNER REPLACEMENT LIST - 01V SERIES Note: Photos not to scale 6 1 ODS pilot assembly 9 2 3 8 24/30" model shown Standard model shown here. Burner system is also available in stainless steel. 5 10 7 4 Replacement parts can be ordered from your local Real Fyre dealer. The log set is purchased and packaged separately; contact your local dealer when ordering. Refer to the instructions included with the log set. 16/18" model 24/30" model Description Part No. Qty. Part No. Qty. 1.
PAGE 14
G10 BURNER REPLACEMENT LIST - 12 SERIES Note: Photos not to scale 5 1 ODS pilot assembly 2 3 4 24/30" model shown Standard model shown here. Burner system is also available in stainless steel. 6 11 10 8 9 12 7 Replacement parts can be ordered from your local Real Fyre dealer. The log set is purchased and packaged separately; contact your local dealer when ordering. Refer to the instructions included with the log set. Item Description 16/18" model 24/30" model Part No. Qty. Part No. Qty.
PAGE 15
G10 BURNER REPLACEMENT PARTS LIST - 15 SERIES Note: Photos not to scale 4 1 ODS pilot assembly 2 10 24/30" model shown Standard model shown here. Burner system is also available in stainless steel. 9 7 8 5 11 3 Replacement parts can be ordered from your local Real Fyre dealer. 6 The log set is purchased and packaged separately; contact your local dealer when ordering. Refer to the instructions included with the log set. Item Description 16/18" model 24/30" model Part No. Qty. Part No.
PAGE 16
WHEN USED AS A VENTED DECORATIVE APPLIANCE (PER ANSI Z21.60) This appliance is for installation in a solid-fuel-burning fireplace (masonry fireplace or manufactured fireplace) with a working flue and constructed of noncombustible material. This burner system may be installed as vented decorative appliance in compliance with ANSI Z21.60 and National Fuel Gas Code, Section 6.6.
PAGE 17
INSTALLATION (cont.) The Real Fyre burner system must be installed by a qualified professional service technician. Instructions must be followed carefully to ensure proper performance and full benefit from the burner system. Fireplace floor must be level, clean, and smooth. Important: When a stainless steel burner system is installed outdoors, ensure it is not directly exposed to the elements (precipitation, rain, wind, etc.). REFER TO THE PARTS LIST WHEN FOLLOWING THESE INSTRUCTIONS.
PAGE 18
INSTALLATION (Cont.) PILOT ON CONTROL SETTINGS OFF It is recommended that before you install the decorative media, you familiarize yourself with the control valve layout. This will assist you when operating the burner system. See Fig. 18-1 through 18-4 for the control positions of your specific model. Fig. 18-1 Manual valve operating positions LIGHTING TEST Prior to proceeding with installation, perform a lighting test (see lighting instructions for lighting your burner).
PAGE 19
INSTALLATION (cont.) LAVA GRANULES (DECORATIVE) 15 model shown 1. Spread the supplied lava granules on the floor of the fireplace; around the front and sides of the burner system (see Fig. 19-1). The lava granules may be placed around the remote receiver (as applicable). Leave the front of the receiver clear for control access. Note: DO NOT place any lava granules on the burner system, or behind it. GLOWING EMBERS AND BRYTE COALS PLACEMENT 1.
PAGE 20
INSTALLATION (cont.) LOG SET PLACEMENT • Follow the instructions included with the log set for step by step log placement. • Read all safety warnings and important information in the instructions supplied with the log set to ensure proper placement. • DO NOT add any additional embers to this setup. Any additional embers will cause unsafe operation. • Periodically check the positioning of the logs to ensure proper log placement.
PAGE 21
INSTALL/REPLACE BATTERIES (IF APPLICABLE) CAUTION: Ensure the unit is connected to the gas line and has been tested for leaks before you insert batteries. CAUTION: Turn off the remote and/or burner and allow the unit to completely cool prior to any battery replacements. Important: Prior to inserting batteries, always apply a small amount of dielectric grease to both ends of each battery. This will ensure conductivity and prevent moisture from affecting the contact.
PAGE 22
CHECK GAS PRESSURE IMPORTANT Check the gas pressure with the system burning and the control fully ON. The burner system and its main gas valve must be disconnected from the gas-supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The burner system must be isolated from the gas-supply piping system by closing its equipment shutoff valve during any pressure testing of the gas-supply piping system at test pressures equal to or less than 1/2 psig (3.
PAGE 23
LIGHTING INSTRUCTIONS - MANUAL VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater. The Real Fyre burner system has an ODS pilot.
PAGE 24
LIGHTING INSTRUCTIONS - 01V(P) VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater. The Real Fyre burner system has an ODS pilot.
PAGE 25
LIGHTING INSTRUCTIONS - SERIES 12 VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.
PAGE 26
LIGHTING INSTRUCTIONS - SERIES 15 VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater. The burner system has an ODS pilot.
PAGE 27
CLEANING AND SERVICING SAFETY INFORMATION Note: Regular cleaning and servicing will be necessary to ensure proper ODS pilot operation and proper burn characteristics. 1. Always shut off the gas to the burner system while performing service work. 2. Allow the burner system to cool before servicing. 3. Installation, service, and repair must be done by an NFI Certified or other qualified professional service technician.
PAGE 28
CLEANING AND SERVICING Only limited cleaning will be required under normal use of the burner system. TO CLEAN THE BURNER SYSTEM 1. Remove the log set and embers. Use a vacuum cleaner to remove loose particles from all surfaces of the system. Do not use cleaning fluids. 2. Dust the assembly and the burners. Using a compressed air duster (commonly available at computer, electronic, or office supply stores) blow through the flash tube, carry over ports, and all of the burner ports.
PAGE 29
CLEANING AND SERVICING (cont.) SYNCING THE REMOTE SYSTEM LEARN 12 models (if equipped) Ensure the burner system is off and completely cool. Locate the 3-position switch on the remote receiver and slide it to the REMOTE position. Use the tip of a pen or a wire clip to push the LEARN button and release. See Fig. 29-1. A beep will be heard. Then press and hold the ON button on the remote transmitter; a series of beeps should be heard. The remote system is now synced. Light burner to test.
PAGE 30
CHECKING THE ODS PILOT FLAME APPEARANCE WARNING: NO ADJUSTMENTS ARE TO BE MADE TO THE ODS PILOT SYSTEM. TAMPERING WITH THIS SYSTEM CAN BE EXTREMELY HAZARDOUS. When installing the burner assembly, it is important to visually check the ODS pilot flame and the burner flames. 1. The ODS pilot flame must be present when the burner is operating. The flame should touch the top of the thermocouple tip (Fig. 30-1 or Fig. 30-3). 2.
PAGE 31
TROUBLESHOOTING • ONLY A QUALIFIED PROFESSIONAL SERVICE PERSON SHOULD SERVICE AND REPAIR THIS APPLIANCE. • TURN OFF UNIT AND ALLOW TO COOL BEFORE TROUBLESHOOTING 1) BURNER SHUTTING DOWN DURING OPERATION POSSIBLE CAUSE SOLUTIONS A. Insufficient or excessive gas pressure A1. Check gas pressure (Read E.- G. of IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION section, & check with local gas company). A2.
PAGE 32
TROUBLESHOOTING (Cont.) POSSIBLE CAUSE 2) SOLUTIONS ODS PILOT WILL NOT LIGHT A. ODS pilot flame lifting off thermocouple/generator A. Check gas pressure (see Section 1, A1 of this table). B. Piezo spark not lighting ODS pilot B. Check to make sure piezo is sparking when pressing / turning igniter. (Note: You may need to press / turn igniter several times to ignite ODS pilot.) See LIGHTING INSTRUCTIONS section. C. Igniter electrode wire loose C. Check wiring and reconnect any loose wiring D.
PAGE 33
TROUBLESHOOTING (Cont.) POSSIBLE CAUSE SOLUTIONS 8) SOOTING A. Low gas pressure A. Check gas pressure (see Section 1, A1 of this table). B. Drafts in room B. Eliminate drafts by closing heating and air conditioning vents, returns, and outside air vents. Fans blowing directly into fireplace should be turned off when system is operating. C. Air shutter(s) blocked C. Burner air shutter(s) are blocked with debris. Vacuum debris in and around burner area. D.
PAGE 34
WARRANTY PETERSON UNVENTED ROOM HEATER GAS APPLIANCE LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Real Fyre® unvented room heater gas appliance to be free from defects in material and workmanship. Peterson unvented ceramic refractory gas logs are warranted for as long as you own them (lifetime). Peterson unvented burner component parts, except valves, ODS pilots, and controls, are warranted for TEN (10) YEARS.