Spec Sheet 1

ManualsBrandsReal Fyre ManualsFireplace/Gas Stove AccessoriesVented Collection GR47-18/20 18" and 20" Rumford Burner with Automatic Variable Valve Remote, Damper Clamp and Flame Pattern Unique Burner in Black

REV 0 -A - 2004290720

L-A2-458

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

This gas log set is to be installed only in a solid-fuel

burning ﬁreplace with a working ﬂue and constructed

of noncombustible material. The installation, including

provisions for combustion and ventilation air must

conform with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the CSA B149.1, Natural Gas and Propane

Installation Code, and applicable local building codes.

A damper clamp, which must be permanently installed,

is included to maintain the minimum permanent vent

opening and to prevent full closure of the damper.

The chimney damper MUST be fully opened when

burning the unit. The unit is designed to burn

with yellow ﬂames; thus adequate ventilation is

absolutely necessary.

To comply with certification, listings, and building

code acceptances, and for safe operation and proper

performance of this gas log set, you must use ONLY

Peterson Real Fyre parts, decorative media, and

accessories. Use of any other controls, parts, or

accessories not designed for use with Real Fyre gas

log sets is prohibited. This will void all warranties,

certiﬁcations, listings, and building code approvals,

and may cause property damage, personal injury, or

loss of life. Peterson will not be liable for any damages

caused by this misuse.

*Note: Solid-fuels shall not be burned in a ﬁreplace

where this product is installed.

FOR INSTALLATION IN

SOLID-FUEL BURNING

FIREPLACES*

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THE UNIT.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier

from a neighbor’s phone. Follow gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁre department.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion

may result, causing property damage,

personal injury, or loss of life.

This appliance is only for use with the type

of gas indicated on the rating plate.

Installation and service must be

performed by a qualiﬁed professional

service technician, service agency, or

the gas supplier.

DESIGN CERTIFIED

Vented Decorative Appliance

ANSI Z21.60

CSA 2.26

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION &

OWNER’S MANUAL

GR47 RUMFORD VENTED GAS LOG SETS

Burner Systems:

GR47- ** (P)A

GR47- ** -02(M)(P)

GR47- ** -17(M)(P)

**Sizes:

(18/20, 24/30)

Regulated burner system for

use w/ propane or natural gas

Summary of content (44 pages)

PAGE 1
INSTALLATION & OWNER’S MANUAL Burner Systems: DESIGN CERTIFIED to Vented Decorative Appliance ANSI Z21.60 CSA 2.26 GR47- ** (P)A GR47- ** -02(M)(P) GR47- ** -17(M)(P) **Sizes: (18/20, 24/30) FOR INSTALLATION IN SOLID-FUEL BURNING FIREPLACES* Regulated burner system for use w/ propane or natural gas GR47 RUMFORD VENTED GAS LOG SETS IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OF THE UNIT.
PAGE 2
INSTALLATION ET MODE D'EMPLOI CONCEPTION CERTIFIÉE à Vented Decorative Appliance ANSI Z21.60 CSA 2.26 Systèmes de brûleur: GR47- ** (P)A GR47- ** -02(M)(P) GR47- ** -17(M)(P) POUR L'INSTALLATION DANS LE COMBUSTIBLE SOLIDE DE BRÛLANT FIREPLACES* **Tailles: (18/20, 24/30) Système de brûleur réglementé l'usage du propane ou du gaz naturel GR47 RUMFORD VENTILÉ SYSTÈMES DE BRÛLEURS IMPORTANT: L I S E Z C E S I N S T RU C T I O N S SOIGNEUSEMENT AVANT DE COMMENCER L'INSTALLATION DE L'UNITÉ.
PAGE 3
TABLE OF CONTENTS GETTING STARTED USE, CARE, & SERVICE LIGHTING INSTRUCTIONS - MANUAL (A) SERIES �� 25 IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION �� 5 FIREPLACE OPERATING SAFETY INFORMATION �� 7 SPECIFICATIONS �� 8 DAMPER CLAMP INSTRUCTIONS �� 11 GR47 BURNER PARTS LIST - MANUAL (A) SERIES �� 12 GR47 BURNER PARTS LIST - 02 SERIES �� 13 GR4
PAGE 4
L'INFORMATION DE SÛRETÉ IMPORTANTE DE PRÉINSTALLATION ET DE CHEMINÉE ATTENTION: L'installation et la réparation doivent être faites par un NFI certifié ou tout autre installateur professionnel qualifié. Installateur: A. B. C. D. E. F. G. H. I. J. K. L. M. N. Lisez soigneusement ces instructions avant d'installer ce système de brûleur à gaz. Soyez sûr que vous comprenez tous les mesures de sécurité et avertissements contenus en ce manuel.
PAGE 5
IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION CAUTION: Installation and repair must be done by an NFI Certified or other qualified professional installer. Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand all safety precautions and warnings contained in this manual. A. BE CAREFUL: If not installed, serviced, and used correctly per these instructions, this product can cause serious personal injury, property damage, or loss of life. B.
PAGE 6
INFORMATIONS SUR LA SÉCURITÉ D'EXPLOITATION DE CHEMINÉE A. Adultes doivent être présents lors de cet appareil au gaz est en marche. Cette unité ne doit pas être laissé sans surveillance ou brûlure lorsque tout quelqu'un dort. B. Gardez le domaine du clair réglé de notation de gaz et libérez des matériaux combustibles, l'essence, et d'autres vapeurs et liquides inflammables. C. Ne pas utiliser cet appareil si une partie quelconque a été submergée.
PAGE 7
FIREPLACE OPERATING SAFETY INFORMATION A. Adults shall be present when this gas appliance is operating. This unit shall not be left burning when unattended or while anyone is sleeping. B. Keep the area of the gas burner system clear and free from combustible materials, gasoline, and other flammable vapors and liquids. C. DO NOT use this appliance if any part has been underwater.
PAGE 8
SPECIFICATIONS Real Fyre gas burner systems must be installed only in a solid-fuel burning fireplace with the minimum firebox dimensions and venting requirements met (see following tables). This appliance is designed to burn with yellow flames; adequate ventilation is absolutely necessary. Product Specifications Minimum Fireplace Size Model Width * BTU Rating Depth ‡ Height Nat. Gas L.P.
PAGE 9
SPECIFICATIONS (cont.) Fireplace Requirements (cont.) Glass Doors If this burner system is installed in a fireplace with glass doors, and the doors have a frame that OBSTRUCTS AIRFLOW to the fireplace floor, the frame MUST have slots (above the fireplace floor) that allow adequate ventilation. See Fig. 9-1. Important: The opening (with doors fully open) MUST meet the minimum fireplace size front width and height requirements. See Table 1 (previous page) and Fig. 9-1.
PAGE 10
SPECIFICATIONS (cont.) 02 SERIES WIRING DIAGRAM 17 SERIES WIRING DIAGRAM Electrode wires Pilot assembly Ignition module Pilot assembly Thermocouple line S Ground wire Battery box Wire harness Remote receiver (optional) Valve Thermo switch Wire harness Manual switch OR Remote receiver Valve Fig. 10-1 Fig.
PAGE 11
DAMPER CLAMP INSTRUCTIONS The damper clamp with hex bolt (Fig. 11-1) is provided as a means to prevent full closure of the damper blade.The clamp is easily attached to most damper blades with pliers or a wrench, and must be permanently installed. The clamp is designed to prevent accidental closure of the damper when installed as illustrated (Fig. 11-2).
PAGE 12
GR47 BURNER PARTS LIST - MANUAL (A) SERIES 1 Thermocouple 3 Pilot 5 24/30" burner model shown 2 6 4 8 9 11 12 10 7 13 Note: Photos not to scale Replacement parts can be ordered from your local Real Fyre dealer. Item The log set is purchased and packaged separately; contact your local Real Fyre dealer when ordering. Refer to the instructions included with the log set. 18/20" model 24/30" model Description Part No. Qty. Part No. Qty. 1.
PAGE 13
GR47 BURNER PARTS LIST - 02 SERIES 1 Heat sensor 4 Pilot 7 24/30" burner model shown 6 5 9 OR 12 Electrode 2 3 11 15 8 10 Remote transmitter and system batteries included with burner system (as applicable). 13 14 Note: Photos not to scale 16 Replacement parts can be ordered from your local Real Fyre dealer. The log set is purchased and packaged separately; contact your local Real Fyre dealer when ordering. Refer to the instructions included with the log set.
PAGE 14
GR47 BURNER PARTS LIST - 17 SERIES 1 Thermocouple 3 7 2 24/30" burner model shown Pilot 10 17 6 12 4 13 14 11 5 18 15 16 Note: Photos not to scale Replacement parts can be ordered from your local Real Fyre dealer. Item 9 8 The log set is purchased and packaged separately; contact your local Real Fyre dealer when ordering. Refer to the instructions included with the log set. 18/20" model 24/30" model Description Part No. Qty. Part No. Qty. 1.
PAGE 15
INSTALLATION The Real Fyre burner system must be installed by a qualified professional service technician. Instructions must be followed carefully to ensure proper performance and full benefit from the burner system. Check to be sure the burner system is designed and labeled for the type of gas (natural or propane gas) supplied to fireplace. Fireplace floor must be level, clean, and smooth (see FIREPLACE SAFETY INFORMATION section).
PAGE 16
INSTALLATION (cont.) INSTALL REMOTE RECEIVER / SWITCH BOX (if applicable - 02 & 17 models) A For 02 models proceed to step 2 1. 17 Models Only: If this unit was shipped with a remote, read and follow the separate remote instructions (packed with remote) for connecting the remote to the valve. Then continue to step 2. Wire harness Bottom (against wall) 4" min. 2. Place the receiver/switch box inside the firebox. Position so that it is: • located at the left front of the firebox.
PAGE 17
INSTALLATION (cont.) PREPARE GRATE AND CENTER 1. Locate the grate (outside of the fireplace), and attach the stabilizer clips to the 2 inner bars of the grate using the provided screws and nuts (see Fig. 17-1 and Fig. 17-3). (24/30" grate shown) The stabilizer clips should be positioned on the inner bars and oriented as shown. Note the 1 1/2" spacing in Fig. 17-3. Tighten the clips in place. 2.
PAGE 18
INSTALLATION (cont.) HEAT SHIELD PLACEMENT 2 heat shields TO PREVENT DAMAGE AND FAILURE: IT IS CRITICAL THAT THE HEAT SHIELD(S) BE PLACED CORRECTLY OVER THE REGULATOR AND/OR VALVE PRIOR TO OPERATION. TO PREVENT OVERHEATING: Place the valve heat shield over the valve as shown in the applicable image of Fig. 18-1. It should rest flat above the valve. Manual and 17 Models For manual and 17 models, place the regulator heat shield as shown in the applicable image of Fig. 18-1.
PAGE 19
INSTALLATION (cont.) SAND/VERMICULITE PLACEMENT The sand/vermiculite supplied with the unit is specially selected for use with either natural or propane gas. It maximizes flame distribution and provides a cleaner burning flame. (17 model shown) CAUTION: Use only sand for natural gas burners and vermiculite for propane gas burners. 1. Fill the burner pan completely with the sand/ vermiculite (see Fig. 19-1). Avoid spilling the sand/ vermiculite on the pilot assembly.
PAGE 20
INSTALLATION (cont.) GRATE PLACEMENT 1. Place the grate over the burner pan so that: • the stabilizer clips fit over the back edge of the pan to lock it in position. • the rear grate legs insert into the wire guard cutouts (if applicable). See Fig. 20-1. 2. Place a second layer of embers lightly and evenly over the burner and grate area. Be sure to cover the grate bars/fingers as shown. See Fig. 20-1. Break up any clumps that may have developed during shipment. Completely cover the area as shown.
PAGE 21
INSTALLATION (cont.) At this stage the burner, media, and grate installation should look as depicted below.
PAGE 22
INSTALLATION (cont.) LOG SET PLACEMENT • Follow the instructions included with the log set for step by step log placement. • Read all safety warnings and important information in the instructions supplied with the log set to ensure proper placement. • DO NOT add any additional embers to this log set. Any additional embers will cause unsafe operation.
PAGE 23
INSTALLING/REPLACING BATTERIES (IF APPLICABLE) CAUTION: Ensure the unit is connected to the gas line and has been tested for leaks before you insert batteries. CAUTION: Turn off the remote and/or burner and allow the unit to completely cool prior to any battery replacements. Important: Prior to inserting batteries, always apply a small amount of dielectric grease to both ends of each battery. This will ensure conductivity and prevent moisture from affecting the contact.
PAGE 24
NOTES PAGE Please use this page to record any information that you may want to have at hand.
PAGE 25
LIGHTING INSTRUCTIONS - MANUAL (A) SERIES FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it. Call a qualified professional service technician. Excessive force or attempted repair may result in fire or explosion. B.
PAGE 26
INSTRUCTIONS D'ALLUMAGE - SÉRIE MANUEL (A) POUR VOTRE SÉCURITÉ, LISEZ AVANT D'ALLUMER AVERTISSEMENT: Si vous ne suivez pas ces instructions à la lettre, un incendie ou une explosion entraînant des dommages matériels, des blessures ou des pertes de vie. A. N'utilisez que votre main pour enfoncer ou tourner le bouton de contrôle du gaz. Ne jamais utiliser d'outils. Si le bouton ne sera pas enfoncer ou à tourner à la main, n'essayez pas de le réparer. Appelez un technicien de service qualifié.
PAGE 27
LIGHTING INSTRUCTIONS - MANUAL (A) SERIES (cont.) WARNING: If the burner fails to light within 5 seconds, turn the control knob clockwise to PILOT. Allow five (5) minutes for any gas in the unit to dissipate, then repeat step 1 above. IF YOU SMELL GAS, SEE STEP B AT BEGINNING OF LIGHTING INSTRUCTIONS. Note: The ignition sequence will take approximately 5 seconds. 1. Ensure the pilot is burning.
PAGE 28
INSTRUCTIONS D'ALLUMAGE - SÉRIE MANUEL (A) (SUITE) Note: La séquence d'allumage dure environ 5 secondes. WARNING: Si le brûleur ne s'allume pas dans les 5 secondes, tournez le bouton de commande vers la droite pour PILOT. Permettre aux cinq (5) minutes pour tout gaz de l'unité de dissiper, puis répétez l'étape 1 ci-dessus. SI VOUS UNE ODEUR DE GAZ, voir l'étape B AU DÉBUT DE instructions d'allumage. SUR 1. Assurer la veilleuse est allumée.
PAGE 29
LIGHTING INSTRUCTIONS - 02 SERIES FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device that automatically lights the pilot. DO NOT attempt to light the pilot by hand. B. BEFORE OPERATING, smell all around the appliance area for gas.
PAGE 30
INSTRUCTIONS D'ALLUMAGE - 02 SÉRIE POUR VOTRE SÉCURITÉ LISEZ AVANT D'ALLUMER AVERTISSEMENT: Si vous ne suivez pas ces instructions à la lettre, un incendie ou une explosion entraînant des dommages matériels, des blessures ou des pertes de vie. A. Cet appareil est équipé d'un dispositif d'allumage qui allume automatiquement la veilleuse. NE PAS essayer d'allumer la veilleuse manuellement. B. AVANT D'UTILISER, Sentez tout autour de l'appareil pour le gaz.
PAGE 31
LIGHTING INSTRUCTIONS - 02 SERIES (cont.) OFF REMOTE ON MANUAL LIGHTING CAUTION: DO NOT attempt to light the pilot by hand. 1. Switch Box Models: Locate the ON/OFF switch at the front of the switch box. Press the switch to the ON (I) position. See Fig. 31-1. The igniter will begin to spark. After the pilot lights and is established, the valve will automatically open and the burner will light. Note: The ignition sequence will take approximately 5 seconds.
PAGE 32
OFF REMOTE INSTRUCTIONS D'ALLUMAGE - 02 SÉRIE (cont.) ON ÉCLAIRAGE MANUEL CAUTION: NE PAS essayer d'allumer la veilleuse à la main. LEARN I O 1. Boîte De Commutateur Modèles: Repérez l'interrupteur ON/OFF (sur/éteindre) à l'avant de la boîte de commutation. Appuyez sur l'interrupteur sur la position ON (I) (sur). Voir Fig. 32-1. Boîte À Distance Modèles: Situez l'interrupteur à 3 positions sur le récepteur à distance (voir la Fig.32-1.), Et faites glisser le commutateur à la position ON (sur).
PAGE 33
LIGHTING INSTRUCTIONS - 17 SERIES FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it. Call a qualified professional service technician. Excessive force or attempted repair may result in fire or explosion. B.
PAGE 34
INSTRUCTIONS D'ALLUMAGE - 17 SÉRIE POUR VOTRE SÉCURITÉ, LISEZ AVANT D'ALLUMER AVERTISSEMENT: Si vous ne suivez pas ces instructions à la lettre, un incendie ou une explosion entraînant des dommages matériels, des blessures ou des pertes de vie. A. N'utilisez que votre main pour enfoncer ou tourner le bouton de contrôle du gaz. Ne jamais utiliser d'outils. Si le bouton ne sera pas enfoncer ou à tourner à la main, n'essayez pas de le réparer. Appelez un technicien de service qualifié.
PAGE 35
LIGHTING INSTRUCTIONS - 17 SERIES (cont.) 2. Locate the remote transmitter and press and hold the ON/HI button (see Fig. 35-1). The ignition sequence will begin. Signal light Note: Continue holding the button to increase the flame. A click will be heard when max flame height is reached. ON/HI button Note: Upon initial use or after an extended period of no use, the ON/HI button may have to be pressed for up to 3 seconds prior to functioning.
PAGE 36
INSTRUCTIONS D'ALLUMAGE - 17 SÉRIE (cont.) 2. Localiser la télécommande et appuyez sur le touche ON/HI (voir Fig. 36-1). La séquence d'allumage commence. Note: Continuez à maintenir le touche pour augmenter la flamme. Un clic se fait entendre lorsque la hauteur max de flamme est atteinte. feux de signalisation Note: Dès la première utilisation ou après une longue période de non utilisation, le touche ON/HI peut être pressée pour 3 secondes avant de fonctionnement.
PAGE 37
LIGHTING INSTRUCTIONS - 17 SERIES (cont.) SHUTTING DOWN MAIN BURNER ONLY (pilot will remain lit): Thermocouple For remote shut down, press and hold the LO/OFF button on the remote transmitter until the burner shuts off. If remote is unavailable, slide the switch on the receiver to the OFF position. For manual shutdown, turn the control knob clockwise to PILOT.
PAGE 38
INSTRUCTIONS D'ALLUMAGE - 17 SÉRIE (cont.) FERMER Vis de réglage de BRULEUR SEULEMENT (pilote reste allumé): Pour arrêt à distance, appuyez et maintenez le bouton LO / OFF sur la télécommande jusqu'à ce que le brûleur est éteint. Si la télécommande n'est pas disponible, faites glisser le commutateur sur le récepteur à la position OFF. Pour un arrêt manuel, tournez le bouton de commande vers la droite pour PILOT.
PAGE 39
CLEANING AND SERVICING Note: Discoloration is common on the grate after burning. Note: Servicing may be necessary to ensure proper pilot operation and proper burn characteristics. Always shut off the gas to the appliance while performing service work. Allow the appliance to cool before servicing. Installation, service, and repair must be done by an NFI Certified or other qualified professional service technician.
PAGE 40
LO/OFF CLEANING AND SERVICING (cont.) SYNCING THE REMOTE SYSTEM (if applicable) Ensure the burner system is off and completely cool. LEARN Locate the 3-position switch on the remote receiver and slide it to the REMOTE position. Use the tip of a pen or a wire clip to push the LEARN button and release. See Fig. 40-1. A beep will be heard. Then press and hold the ON or ON/HI button on the remote transmitter; a series of beeps should be heard. The remote system is now synced.
PAGE 41
TROUBLESHOOTING POSSIBLE CAUSE 1 SOLUTIONS BURNER SHUTTING DOWN DURING OPERATION A. Insufficient or excessive gas pressure A1. Check gas pressure (Read D.- F. of IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION section, & check with local gas company). A2. Other gas appliances may be on the same gas line, dropping gas pressure to log set. Check pressures with everything operating to ensure adequate pressure. B. Log placement B.
PAGE 42
TROUBLESHOOTING (Cont.) POSSIBLE CAUSE SOLUTIONS 5 ODORS A. Gas leak A. Shut off gas, if possible. Follow instructions on front page. Have a qualified professional installer or the gas company correct all leaks. B. New home, new carpet, or new paint B. When these odors are drawn into the fireplace, this may cause objectionable odors. Thoroughly ventilate the area before restarting your log set. C. Damper closed C. Ensure that damper is open. 6 SMOKING AND/OR SOOTING A.
PAGE 43
ELECTRONIC PILOT TROUBLESHOOTING (IF APPLICABLE) Detail A Electrode (A) When adjusting the spark electrode (if necessary); NEVER adjust the electrode by bending the wire. ALWAYS adjust the electrode by loosening the retainer nut(s), then adjust accordingly. The minimum gap between the spark electrode/ heat sensor and the pilot flame hood is 1/8". The maximum is 5/32". Hood Spark electrode Electrode Ceramic Threaded barrel 1/8" min. gap Heat sensor 1/8" min. gap Fig.
PAGE 44
WARRANTY PETERSON INDOOR VENTED DECORATIVE GAS APPLIANCE LIMITED WARRANTY Robert H. Peterson Co. ("RHP") warrants your Real Fyre® vented decorative gas appliance to be free from defects in material and workmanship. This warranty is for indoor use only. Peterson vented ceramic refractory gas logs are warranted for as long as you own them (lifetime). Peterson vented burner assemblies excluding valves, pilots, and controls are WARRANTED for TEN (10) YEARS.