Spec Sheet 1

ManualsBrandsReal Fyre ManualsFireplace/Gas Stove AccessoriesVented Collection PB-24 24" Pan Burner with Flat Burner Pan Provides Full Flame, Connector Kit and Damper Clamp in Black

L-A2-226REV 5 - 1508171425

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

Owner’s

Manual

Designed to:

Z21.84b-2004

(16" - 42" models)

Burner Systems:

PB-16(P)

PB-18(P)

PB-24(P)

PB-30(P)

PB-36(P)

PB-42(P)

FOR INSTALLATION IN

SOLID-FUEL BURNING

FIREPLACES*

The Real-Fyre gas burner system is to be installed only

in a solid-fuel burning ﬁ replace with a working ﬂ ue and

constructed of noncombustible material. The installation,

including provisions for combustion and ventilation air

must conform with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or the CSA B149.1, Natural Gas

and Propane Installation Code, and applicable local

building codes.

A damper clamp is included to maintain the minimum

permanent vent opening and to prevent full closure of

the damper blade. The chimney damper MUST be fully

opened when burning the burner system. The burner

system is designed to burn with yellow ﬂ ames;

thus adequate ventilation is absolutely necessary.

To comply with certiﬁ cation, listings, and building

code acceptances, and for safe operation and

proper performance of this burner system, use

ONLY Peterson parts and accessories. Use of

other controls, parts, and accessories that are

not designed for use with Real-Fyre gas burner

systems is prohibited and will void all warranties,

certiﬁ cations, listings, and building code approvals,

and may cause property damage, personal injury,

or loss of life.

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THE SYSTEM.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier

from a neighbor’s phone. Follow gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁ re department.

This appliance is only for use with the

type of gas indicated on the rating plate.

Installation and service must

be performed by a qualified

professional installer, service

agency, or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

PB SERIES VENTED GAS BURNER SYSTEMS (UNREGULATED)

FOR USE WITH

FYRE GLASS / FYRE GEMS

WARNING

If the information in this manual is not

followed exactly, a fire or explosion

may result, causing property damage,

personal injury, or loss of life.

Summary of content (16 pages)

PAGE 1
Owner’s Manual Designed to: Burner Systems: Z21.84b-2004 PB-16(P) PB-18(P) PB-24(P) PB-30(P) PB-36(P) PB-42(P) (16" - 42" models) FOR INSTALLATION IN SOLID-FUEL BURNING FIREPLACES* FOR USE WITH FYRE GLASS / FYRE GEMS PB SERIES VENTED GAS BURNER SYSTEMS (UNREGULATED) WARNING If the information in this manual is not followed exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life.
PAGE 2
TABLE OF CONTENTS 3 4 4 5 6 6 8 8 9 10 10 10 10 10 11 12 13 14 16 PARTS LIST IMPORTANT INFORMATION FIREPLACE REQUIREMENTS GLASS / GEMS QUANTITY DETERMINATION INSTALLATION INSTALLING THE BURNER GLASS / GEMS PLACEMENT BURNER PREPARATION OPERATING INSTRUCTIONS CLEANING AND MAINTENANCE MAINTENANCE CLEANING SERVICE FLAME DESCRIPTION PILOT BURNER ADJUSTMENT (IF EQUIPPED) NOTES PAGE OPTIONAL CONTROLS FOR YOUR REAL-FYRE® BURNER SYSTEM TROUBLESHOOTING WARRANTY Tools Recommended WARNING The following tools and su
PAGE 3
PARTS LIST Before installation, check that your gas burner system is complete. See the parts list below. If any parts are missing or damaged, contact your Real-Fyre® dealer. Be sure you know the model and size of your set when ordering options or replacement parts and accessories. 1 2 4 Connector kit 4A 3 5 Item No. Description Qty. 1. Burner pan 1 2. Fuel injector / air mixer 1 3. Damper clamp with bolt 1 4. Connector kit (with adapters) 1 5. Select sand granules (nat.
PAGE 4
IMPORTANT INFORMATION Important: To comply with certification, listings, and building code acceptances, and for safe operation and proper performance of this burner system, use ONLY Peterson Real-Fyre® parts and accessories. Use of other controls, parts, and accessories that are not designed for use with Real-Fyre® gas burner systems is prohibited and will void all warranties, certifications, listings, and building code approvals, and may cause property damage, personal injury, or loss of life.
PAGE 5
GLASS / GEMS QUANTITY DETERMINATION CAUTION: Sand granules are for use with natural gas systems only. Always use vermiculite granules for propane gas systems. The granules that come with the burner system are pre-measured and must be used per these instructions (see GLASS / GEMS PLACEMENT section). Decorative glass / gems (purchased separately) must be placed to cover the burner (but not on the valve or pilot, if equipped). See Table 5-1 for the minimum bag requirement depending on your burner size.
PAGE 6
INSTALLATION The damper clamp with hex bolt (Fig. 6-1) is provided as a means to prevent full closure of the damper blade. The clamp is easily attached to most damper blades with pliers or a wrench, and must be permanently installed. The clamp is designed to prevent accidental closure of the damper when installed as illustrated (Fig. 6-2 and Fig. 6-3).
PAGE 7
INSTALLATION (cont.) 5. Be sure gas to the fireplace is off. Attach the large adapter (Item 4A) to the gas-supply stub using a pipe compound resistant to all gases. Tighten securely. Then attach the open end of the flex connector to the large adapter. Tighten securely. Ensure the pan rests level on the fireplace floor after connection. Adjust the pan if necessary. 6.
PAGE 8
GLASS / GEMS PLACEMENT BURNER PREPARATION (Pack granules in pan) Burner pan Granules up to baffle Fig. 8-1 Separator screen After hooking up the burner to the fireplace gas supply and placing the heat shield on the valve assembly (if applicable), the decorative media (granules and glass / gems) must be added for the burner to function as designed. Note: Installation is the same for glass and gems. Glass shown here.
PAGE 9
OPERATING INSTRUCTIONS Before operating your gas log set: 1. Be sure your fireplace is free from flammable liquids or combustible materials. 2. Be sure your damper is open. 3. Smell all around the gas log set for the odor of escaping gas. IF YOU SMELL GAS, FOLLOW THE INSTRUCTIONS ON P. 1. If your gas log set is operated by the fireplace valve: 1.
PAGE 10
CLEANING AND MAINTENANCE MAINTENANCE SERVICE Once installed and operating properly, your RealFyre® glass burner will require regular maintenance. You should inspect your glass burner and controls (where installed) for the following: While some minor service conditions can be handled by the owner of the glass burner, a qualified professional service technician should be called to maintain and service your glass burner and any installed control systems.
PAGE 11
PILOT BURNER ADJUSTMENT (IF EQUIPPED) The pilot burner is preset at the factory and should normally not require any adjustment. However, should adjustment be necessary, the following steps should be taken: With the pilot burner lit and the control knob in the pilot position, remove the heatshield covers. Adjust the screw located on the control valve (see Fig. 11-1). Using a screwdriver, turn the pilot adjustment screw slowly clockwise to reduce the flame, or counterclockwise to increase the flame.
PAGE 12
NOTES PAGE Please use this page to record any information about your burner system that you may want to have at hand.
PAGE 13
OPTIONAL CONTROLS FOR YOUR REAL-FYRE® BURNER SYSTEM This unit may come without a valve installed. It may be connected directly to and operated by your fireplace valve. Alternatively, your Real-Fyre® burner may be operated using a number of optional Peterson control systems (listed below). Peterson control systems are engineered to provide convenient, safe, and reliable operation of your gas burner system.
PAGE 14
TROUBLESHOOTING SYMPTOM 1. Smoking and/or sooting CAUSE A. Poor draft or downdraft A. Check for chimney blockage. Be sure chimney is at least 3' taller than anything within 10' of it in all directions. If not, consult a chimney sweep. Chimney cap or fan may help. Under severe conditions, you may need to open a window near the fireplace about 1" to 2" when burning the unit. B. Damper closed B. Open damper fully when operating burner system. C.
PAGE 15
TROUBLESHOOTING (cont.) SYMPTOM 3. Uneven flame distribution (Lower at one end of the burner) 4. Flame at air mixer (For propane units) CAUSE SOLUTION A. Clogged or blocked portholes A. Clear out burner ports. B. Insufficient gas pressure and/or supply B. Consult installer or plumber (see solution 2B). C. Decorative media may be packed down too tightly C. Loosen media around burner pipe by running a kitchen knife along both sides of the pipe. Even out media in burner pan. D.
PAGE 16
WARRANTY PETERSON VENTED DECORATIVE GAS APPLIANCE LIMITED WARRANTY All Peterson gas logs are WARRANTED for as long as you own them (lifetime). All Peterson burner assemblies are WARRANTED for TEN (10) YEARS. All Peterson glass is WARRANTED for FIVE (5) YEARS. SPK-26 controls are covered by a THREE (3) YEAR “All Parts” Warranty. All other Peterson valves, pilots, and controls are covered by a ONE (1) YEAR Limited Warranty (excluding batteries).