Instructions / Assembly

ManualsBrandsReal Solutions for Real Life ManualsCabinet & Furniture HardwareMulti-Drawer Installation Kit

1. Determine your preferred height by holding the top basket up in the cabinet, taking into account the drawer contents

and any other obstructions (i.e. hinges).

2. Measure from the bottom mounting bracket of the basket to the floor of the cabinet. (Fig. 1), and then add 2" to get

Measurement A.

3. Mark the approximate center of the back wall cabinet at Measurement A. Then at the same height, make a second mark

about 4" to the left of the center. (Fig. 2)

4. With the installation template arrow pointing up, insert the right rear mounting socket into the template. The “A” side of

the socket should face towards the center of the cabinet as shown. (Fig. 3) The “V” notch on the socket should align

with the “V” notch on the template as shown. (Fig. 4) Press socket firmly until it is seated into the template. Repeat for

the left rear mounting socket.

5. Press the locking button on the template and extend it to match the width of the basket by selecting 11", 14" or 17".

(Fig. 5)

6. Peel the film from the sticky tape on the back of the rear mounting sockets.

7. Align the template with the marks on the back wall of the cabinet and center the template from left to right so there

is equal space on either side. Push the sockets firmly onto the back wall ensuring the tape is attached. (Fig. 6)

8. If you have a 1/4" thin back wall, continue to Step 9. Otherwise, skip to Step 14.

310371-B_A (0513)

2700 Oak Industrial Drive NE

Grand Rapids, MI 49505 USA

800.253.1561 | 616.459.3311

www.kv.com

Knape & Vogt

™

reserves the right to change specifications without notice.

Made in U.S.A.

STACK KIT

Installation Instructions

Works with 11.5" to 19.75" wide cabinet openings

Tools Required

 •Drill

 •1/8"DrillBit

 •5/16"DrillBit

 •Screwdriver

 •TapeMeasure

Parts Included Qty.

A. Template 1

B. Rear Mounting Sockets 2

C. Front Mounting Brackets 2

D.#6x5/8"PanHeadScrews 8

E.#6x3/4"FlatHeadScrews 8

Face Frame with Wire Basket

Frameless with Wood Basket

Fig. 3

Fig. 4

Product Assemblies

STACKKIT-R-BLK

“V” Notch

Press

Measurement A

Fig. 5

Fig. 1 Fig. 2

Height + 2" = Measurement A

Fig. 6

Summary of content (9 pages)

PAGE 1
STACK KIT Installation Instructions Works with 11.5" to 19.75" wide cabinet openings Frameless with Wood Basket Face Frame with Wire Basket Tools Required • Drill • 1/8" Drill Bit • 5/16" Drill Bit • Screwdriver • Tape Measure Parts Included A. Template B. Rear Mounting Sockets C. Front Mounting Brackets D. #6 x 5/8" Pan Head Screws E. #6 x 3/4" Flat Head Screws 1.
PAGE 2
9. Mark the center of the holes onto your back cabinet wall. (Fig. 7) 10. Remove rear mounting sockets and template from the cabinet wall then remove sockets from template. Using a 5/16" drill bit, drill holes 1-4. 11. Insert anchors completely into the holes and press the red pin into the anchors by hand to open them, (Fig. 8) then remove red pin. 12. Take left rear mounting sockets and align screw locations with the anchors along the back wall of the cabinet.
PAGE 3
24. Insert the basket into rear sockets at an angle until you reach the desired depth as shown. (Fig. 16) 25. Lower the front steel mounting strap into front mounting brackets and press firmly while supporting the bottom of the mounting brackets until basket snaps into both brackets as shown. (Fig. 17) a. If the strap does not snap into the front mounting brackets, then lift the basket at an angle and adjust the depth of the basket in the back mounting socket and lower again. Fig. 17 26.
PAGE 4
KIT DE TIROIRS EMPILABELS Instructions relatives à l’installation Pour ouvertures de meubles de 29,2 cm à 50,2 cm de large Sans façade avec panier en bois 1. Déterminez votre hauteur préférée en tenant le panier supérieur dans le haut du meuble, en tenant compte du contenu du tiroir et d'autres obstacles (par ex. charnières). 2. Mesurez à partir du support de montage inférieur du panier jusqu'au plancher du meuble. (Fig. 1), puis ajoutez 5,1 cm pour obtenir la Mesure A. 3.
PAGE 5
9. Marquez le centre des orifices sur la paroi arrière du meuble. (Fig. 7) 10. Retirez les supports de montage arrière et le gabarit de la paroi de l'armoire, puis retirez les supports du gabarit. Avec une mèche 5/16", percez les trous 1-4. 11. Insérez les chevilles complètement dans les trous et enfoncez à la main la clavette rouge dans les chevilles pour les ouvrir, (Fig. 8) puis retirez la clavette rouge. 12.
PAGE 6
24. Insérez le panier dans les supports arrière à un angle atteignant la profondeur désirée, comme illustré. (Fig. 16) 25. Abaissez le support de montage en acier dans les supports de montage avant et appuyez fermement tout en soutenant le bas des supports de montage jusqu'à ce que le panier s'enclenche dans les deux supports comme indiqué. (Fig. 17) a.
PAGE 7
KIT DE APILAMIENTO Instrucciones de Instalación Sirve para aperturas anchas de gabinetes de 29,2 cm a 50,2 cm Sin marco con cesta de madera Marco de superficie con cesta de alambre Herramientas Requeridas • Taladro • Broca de 1/8" • Broca de 5/16" • Destornillador • Cinta métrica 1. Determine su altura deseada levantando la cesta superior en el gabinete, teniendo en cuenta el contenido de la gaveta y otro tipo de obstrucciones (como bisagras). 2.
PAGE 8
9. Marque el centro de los orificios en la pared posterior del gabinete. (Fig. 7) 10. Retire los receptáculos de montaje posteriores y la plantilla de la pared del gabinete y, luego, retire los receptáculos de la plantilla. Con una broca de 5/16", perfore orificios del 1 al 4. 11. Inserte los anclajes completamente en los orificios y presione la clavija roja en los anclajes manualmente para abrirlos (Fig. 8) y, luego, retire la clavija roja. 12.
PAGE 9
24. Inserte la cesta en los receptáculos posteriores de forma inclinada hasta que alcance la profundidad deseada como se muestra (Fig. 16) 25. Baje la correa de montaje de acero frontal en los soportes de montaje frontales y presione firmemente mientras sostiene la parte inferior de los soportes de montaje hasta que la cesta encaje en ambos soportes como se muestra. (Fig. 17) a.