Installation Manual

ManualsBrandsReal Wheels ManualsAccessories & PartsRealWheels RW-PPK-0403 Air Guard Tire Pressure Monitor with Security Locking System, (Pack of 6)

Read instructions carefully before installation.

If you have questions call 1-800-982-1180.

Installation of RWTG1236 LED AirGuard Set & Go

1. Check Tire Pressure

Set tire to the recommended pressure for your vehicle

before attaching the LED AirGuard Set & Go.

At a glance: how the LED AirGuard Set & Go works.

The LED AirGuard Set & Go is an active tire pressure monitor, it allows for

easy installation and accurate monitoring.

Out of the package and whenever the LED AirGuard Set & Go is not installed

on a pressurized tire it will always be set at zero and not calibrated to

any pressure. Once it is securely threaded onto a tire valve stem, it will

automatically calibrate and sets itself to that tire pressure. At that point if

the tire pressure drops between 5 to 10 psi the LED AirGuard Set & Go will

begin to ﬂash and will continue to ﬂash for up to 3 weeks, until it is removed

and the tire pressure is replenished to the previous tire pressure setting, or

a new tire pressure setting. Note: If the LED AirGuard is ﬂashing and you

remove it from the tire air valve and do not replenish the tire pressure back

to your desired amount; when you reinstall the Set & Go it will automatically

recalibrate to the lower tire pressure, not the previous tire pressure setting

that your tire was originally inﬂated to.

Note: Instructions continued on back.

2. Install Spot-Check Rubber Tester

Find the Spot-Check Rubber Tester located in its own Zip-Lock plastic

bag. Next insert the Spot-Check Rubber Tester into the threaded end

of the LED AirGuard Set & Go. (See Photos 2A & B.)

2A 2B

Spot-Check

Rubber Tester

LED AirGuard

Set & Go

• Set tire to the recommended pressure before attaching LED AirGuard.

• Use the LED AirGuard Set & Go only with ISO 9413 approved valve stems.

These are the most common vehicle valve stems.

• The recommended temperature range is -40°F to +275°F. The batteries do not

give full capacity in very cold or hot temperatures, yet the batteries will regain

their strength when temperatures return to normal.

• The LED is not designed to be seen inside the vehicle.

• A 5 –10 psi drop from the original calibration pressure will trigger the LED ﬂashing.

• Recommended pressure range: 10psi–200psi

• Expected battery life: Standby 2–3 years from the date stamped on the

LED AirGuard Set & Go. Flashing battery life: 3 weeks.

• Pressure peaks: LED AirGuard Set & Go can handle pressure peaks up to

200psi/13.7bar above calibration pressure. A pressure peak can occur for

example when the tire hits a hole in the road.

• Do not drive even short distances with severely underinﬂated tires, since it is

extremely unsafe and it will ruin your tire.

• It is recommended that the LED AirGuard Set & Go is used only in conjunction

with RealWheels Brand of Air Valve Extensions.

• Since the tires naturally lose some pressure, we suggest that if you are going to

put your tires or vehicle in storage you remove the LED AirGuard Set & Go.

• Harsh chemicals should never come in contact with the clear plastic of the

LED AirGuard Set & Go. For example, brake cleaner and chemical thread-lock

(such as Loctite) will cause the plastic to become brittle and crack and may

result in product failure. We suggest removing the LED AirGuard Set & Go before

using any type of chemicals on or around the wheels.

Liability

• The LED AirGuard Set & Go is only an aid in monitoring low tire pressure. Even

when using the LED AirGuard Set & Go, you should still follow the instructions in

your vehicle’s owner’s manual regarding tires and tire pressure maintenance.

• The LED AirGuard Set & Go does not relieve you from your obligations of

regularly checking your tire pressure. We limit our maximum liability to the

purchase price of this product.

Limited Warranty

• The LED AirGuard Set & Go comes with a one (1) year limited manufacturer

warranty. We guarantee that this product is free from any manufacturing defects.

If found defective, return to your Authorized RealWheels Dealer or directly to

RealWheels at the address on back with a copy of the purchase receipt. We will

examine the unit and replace or reimburse you for the units if found faulty under

the warranty.

• This warranty gives you speciﬁc legal rights, and you may also have other rights

which vary from state to state.

Summary of content (2 pages)

PAGE 1
Installation of RWTG1236 LED AirGuard Set & Go Read instructions carefully before installation. If you have questions call 1-800-982-1180. At a glance: how the LED AirGuard Set & Go works. 1 The LED AirGuard Set & Go is an active tire pressure monitor, it allows for easy installation and accurate monitoring. Out of the package and whenever the LED AirGuard Set & Go is not installed on a pressurized tire it will always be set at zero and not calibrated to any pressure.
PAGE 2
3A 3B 3. Test the LED AirGuard Set & Go Using the Spot-Check Rubber Tester Place the LED AirGuard Set & Go with the Spot-Check onto the wheel air valve and push. (See Photo 3A & 3B.) The LED will light up red and flash. This is your indication that the LED AirGuard Set & Go’s batteries are good and the unit is functioning properly. Note: If the LED AirGuard Set & Go does not light up and flash you may have to push harder or the batteries maybe exhausted. 4A 4B 4C 4.