TRIPOD & MONOPOD MANUAL
SERIES AND MODELS Our tripods & monopods vary in height, weight, load capacity, and features. ‘Pods within the same Series share a common load capacity. See our website for detailed specifications.
SERIES AND MODELS Versa Series 2 Quick-Column Fixed Series 1 Series 1 TQC-14 Mk2 TFC-14 Mk2 TVC-24 Mk2 TVC-23 Mk2 TVC-24L / TFC-24L Mk2 Versa Series 3 TVC-33S Mk2 TVC-33 Mk2 TVC-34 Mk2 TVC-34L Mk2 Versa Series 4 TVC-43 Mk2 3 TVC-44 Mk2 www.ReallyRightStuff.
FEATURES AT-A-GLANCE Our tripods are made with carbon fiber, hard anodized 6061‑T6 aluminum, and stainless steel. Made in the U.S.A. 1. Mounting Stud ⁄8” Mounting Stud securely attaches to tripod heads. 3 2. Spirit Level The bullseye helps you level your tripod with ease (Versa tripods only). 3. Angle Stop The Angle Stop ratchets into place to set leg angle. 4. SureGrip™ Apex Lock Carry your tripod over your shoulder with confidence.
BASIC TRIPOD USE Before taking your tripod afield, take a moment to familiarize yourself with its operations. 1 2 3 4 1. Swing out all three legs. 2. Grab all twist locks with one hand and rotate one quarter turn. 3. Pull leg until fully extended. 4. Tighten twist locks. 5. Repeat on all legs. 6. To collapse, loosen twist locks and collapse leg. Grab all twist locks with one hand and tighten. All tripod feet are loose.
SETTING LEG ANGLES For low-level settings, use the ratcheting Angle Stop as shown below. 1. Swing leg inward slightly. 2. Slide Angle Stop out completely. (Slide back in at any time to cancel.) 3. Swing leg to horizontal position. Angle Stop will engage. 4. Move to desired position. Angle Stop will ratchet automatically.
REVERSE THE STUD The threaded platform stud is dual-threaded ¼”-20 and 3⁄8”-16 and is reversible. Follow the steps to reverse the stud from 3⁄8”-16 to ¼”-20. 1. Use 5/32” hex key to unscrew and remove the Stud. 1 2. For tripods with fixed apexes, the Strap & Strap Pin must be removed before the Stud can be re-installed. Use 5/32” hex key to unscrew and remove the Strap Pin. 3. Turn the tripod upside down. Use 5/32” hex key to re-install the Stud by screwing it into the bottom of the apex. 2 4.
ADJUST THE SET SCREW The Mk2 tripods with fixed apexes come with one Set Screw that can be used to prevent your tripod head from coming loose. For clarity, drawings do not show the tripod head installed to the tripod. Install your tripod head, then follow steps. Set Screw 1. Swing leg closest to Set Screw inward slightly. 2 2. Pull Angle Stop out until it stops, then swing leg completely out. 1 3 8 3. Insert 2.
MAINTENANCE Regular maintenance of your tripod is highly recommended to keep its performance and appearance in top shape. Your tripod is built to last through years of use with proper maintenance and care. Protect your investment by following this guide to good maintenance practices. »» Check SureGrip™ set screws for proper tightness to ensure the Apex accessory is secure. Use provided hex key to make adjustments as necessary.
CLEANING Avoiding harsh environments such as sand and saltwater is essential to preserving the life of your tripod. However, we do understand that sometimes it is unavoidable. Therefore, we have made it simple to disassemble the leg portions for thorough cleaning. 1a 1b 1c 2 1. Unscrew Twist Lock and fully remove leg section. 2. Remove Twist Lock, foot, and Anti-Twist Sleeves. 3. Wipe down leg, foot, and exposed threads with damp cloth, removing any dirt or debris. Allow to dry. 4.
QD STRAP SYSTEM Look no further for the most clever shoulder strap system for your RRS tripod*. This new system incorporates QD “Quick-Detach” mounting hardware and allows the strap to be quickly and easily removed at any time. The system has two parts: Two QD Mounts Apex QD Mount + Leg QD Mount Leg QD Mounts come in 3 sizes for RRS Series 1, 2, and 3 tubes. QD-Compatible Strap Strap must have two QD sling swivels.
QD STRAP SYSTEM Apex QD Mount For Series 4 Install Apex QD Mount to underside of apex with two screws. For Fixed and Versa Series 1/2/3 Install Apex QD Mount into threaded socket on side of apex.
CHANGING APEX ACCESSORIES Apex Accessories are only available for Mk2 Versa Tripods. Your tripod head must first be removed from the Mounting Stud. 2 1. loosen all three SureGrip™ set screws around Apex. Two rotations are sufficient, complete removal is not required. 1 2. Remove Apex platform or other accessory by pushing it upward. 3. Insert compatible accessory.
‘POD ACCESSORIES Tripod & Monopod Accessories to fill all your photography needs. for Versa Series 2 TA-2-QC for Versa Series 3 TA-3-QC Versa Quick Columns With integrated SureGrip™ MTX Multi-Tool The best tool for your tripod. Replacement Feet Great for tripods & monopods. TA-3-FRC Rock Claws for rocky terrain. TA-3-FS Foot Spikes for shifting terrain. Leveling Bases Choose Platform or Clamp A leveling base on your tripod is the perfect foundation for gimbal heads, pano gear, and even ballheads.
THANK YOU Thank you for purchasing a Really Right Stuff Mark 2 tripod. Many years ago, we set out to create tripods that would exemplify the best in craftsmanship and quality. We are proud to present to you the results of that pursuit. Our ‘pods are the culmination of first-hand experience and abundant input from seasoned professionals.
www.ReallyRightStuff.
