HIGH PRESSURE WASHER INSTRUCTION MANUAL BY02-VBS-WT WARNING: Do not use the appliance without reading the instruction manual.
- t tri English The symbol on the product or on its packing indicates that this product may not be treated as household waste. Instead it shall be handed over To the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
- t tri Español El símbolo que aparece en el producto o en su embalaje indica que este producto no puede ser tratado como residuo doméstico. En su lugar, debe ser entregado en el correspondiente punto de recogidapara el reciclado de equipos eléctricos y electrónicos.
EN Thank you for choosing the High Pressure Washer Product Overview Chapter 1. 2. 3. 4. 5. 6. 7. 8. Page Safety instructions First time instructions Operating instructions After use instructions Environmental protection Warranty conditions Maintenance, cleaning, repair Trouble shooting Motor Max. pressure Max. flow Current Voltage Max. wate r temp erat ure Brush 1900PSI 1.65GPM 13A 120V/60 Hz 40°C 5 7 8 10 10 11 11 12 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
EN 1. Safety Instructions The appliance is designed solely for outdoor private use and NOT for commercial use. Please keep it away from heat, direct sunlight, moisture and rain, frost and sharp edges. Do not let people who have not been trained in the use of a high pressure washer nor read the instruction manual operate the machine! High pressure cleaners shall not be used by children or untrained personnel. Children should be supervised to ensure that they do not play with the appliance.
EN WARNING: Inadequate extension cables can be dangerous. Cables on reels should always be completely unwinded to prevent the cable from overheating. WARNING: Inadequate extension cords can be dangerous. If an extension cable is used, the plug and the socket must be waterproof and comply with the below-mentioned requirements for length and cable dimensions. 1.0 mm² max. 12.5 m 1.5 mm² max.
EN This section will explain in details how to make you high pressure washer ready for use. Slide the storage hooks (6) into the holders. 1. Insert the extension lance into to the housing 2. Fix the extension lance with the two screws to the housing 3. Insert the rotor arm into the extension lance 4. Insert the U-pin to fix the rotor arm.
EN 1. Attach the high pressure hose (10) to the trigger gun (11) and machine. 1. Screw the water inlet coupling (1) tight on to the water inlet Note: The inlet filter (A) must always be fitted in the water inlet pipe to filter out sand, lime stone and other impurities as these will damage the pump valves. Caution: Failure to fit the filter will invalidate the guarantee. 2. Connect the garden hose with a standard quick coupling Detach the high pressure hose by pressing the pawl (A) or button (B) 1.
EN An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. IMPORTANT! Only use water without any impurities. If there is a risk of sand particles in the inlet water (i.e. from your own well), an additional filter should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is not clogged up. 2.
High pressure detergent 1. Unscrew the container (A) from the high pressure detergent bottle . 2. Add detergent to the container (A) and screw the container to the high pressure detergent bottle 3. Adjust the amount of detergent with the button (B) 4. Foam equipped quick connector. Press (C), then insert into the gun. Caution: When attaching the detergent bottle, the button (C) should come out again. Check before activating the trigger that the nozzle is properly fixed.
EN The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (press the start/stop switch (5) “O” and detach water hose, high pressure hose (10) and nozzle (16-21) 2. Restart the machine (5) and activate the trigger of the trigger gun (11). Let the machine run until no more water runs through the trigger gun (11) 3. Stop the machine, unplug and wind up hose and cable. 4.
Carefully loosen the filter with a screwdriver and clean it (see section 3.1). Check that it is intact before remounting it. The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the warranty The machine should be kept clean so as to let cooling air pass freely through the machine vents.
EN S m t m Machine refuses to start Fluctuating pressure mm n Machine not plugged in Plug in machine. Defective socket Try another socket. Fuse has blown Replace fuse. Switch off other machines. Defective extension cable Try without the extension cable. Pump is sucking air Check that hoses and connections are airtight.
Zhejiang Xinchang BigyaoPower Tool Co., Ltd Head Office: Mengjiatang Industrial Zone, Xinchang County, Zhejiang Province, China USA Office: 101 wales avenue,Avon,MA 02322,United States Service Hotline: 888-899-1688 Email: realminfo@yahoo.