ELECTRIC PRESSURE WASHER Model BIMH CAUTION : All Operators Must Read These Instructions Before Use.
IMPORTANT! Safety Instructions The appliance has been designed solely for private use outdoors and not for commercial use. Keep this appliance away from heat, direct sunlight, moisture and rain, ice and sharp edges. Do not allow anybody that has not been trained to use a pressure washer to operate the machine without first reading the instruction manual. WARNING! High-pressure washers must not be used by children or untrained persons.
2 If an extension cable is used, the plug and socket must be waterproof and conform to the requirements below regarding the length and dimensions of the cable. 1,0 mm ² max. 12,5 m 1,5mm²max.20 m If the power cable is damaged, it must be replaced by the manufacturer, their service agent or a qualified professional in order to avoid any danger.
Know Your Electric Pressure Washer Read the operator’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. 1. High pressure hose 16. Power cord 2. Trigger(with safety lock) 17. Fittings storage 3. High pressure hose connection 18. Wheel 4.
Product Description Purpose • Water inlet pipe This high-pressure electric power washer is intended for residential use to clean vehicles, machines, buildings, facades, etc. • Power cord Areas of application • Needle clean out tool Never use the machine in potentially explosive areas under any circumstances! The operating temperature must be between 32ºF (0ºC) and 104ºF (40ºC). The machine consists of an assembly with a pump, which is encased in a shockabsorbing housing.
Assembly Technical data Motor Max. pressure Max flow Current Voltage Vibration gun Max. Water Inlet Temperature Induction 2600PSI 1.75GPM 15A 120V~/60Hz Max 1.90 m/s2 1. Position the washer as CLOSE as possible to the water supply. 2. The washer must be used on a secure and stable surface in a standing, upright position (Fig. 1). 104ºF/40ºC The Circuitry 3. Screw the transaction handle to the electric pressure washer unit(Fig. 2).
4. Insert the power cord holder(Fig. 3) and trigger gun holder (Fig. 4) into its position. 5. Screw the spray lance into the trigger gun and rotate it until the two parts are completely locked. (Fig. 5) Fig.5 Fig.3 6. Connect the high-pressure hose to the trigger gun and the water outlet (Fig. 6). Fig.6 Fig.4 High pressure hose WARNING! Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose. 7.
Fig.7 9. Make sure the motor switch is pushed to the OFF position before plugging the unit into the power outlet(Fig.9). Fig.9 Water inlet Garden hose 8. Attach garden hose to water supply (Fig. 8). Fig.8 Connect to water supply 10. Check that the electrical supply voltage and frequency(Volt/Hz) correspond to those specified on the pressurewasher rating plate. If the power supply is correct, youmay now plug the pressure washer into the power outlet (Fig. 10). Fig.
Operation IMPORTANT! This pressure washer is 3. Turn the switch to the ON position to start the pressure washer (Fig. 12). equipped with a micro-switch sensitive to water flow. This Total Stop System (TSS) senses water flow in the pump. When the trigger is released, water stops flowing through the pump. The TSS then automatically turns the motor off to protect the pump from overheating, thus saving energy and prolonging pump life. Fig.
3. Snap the desired nozzle into the spray lance tight (Fig. 13). Fig.13 to use. Prepare the cleaning solution as instructed on the solution bottle. 1.Remove the cap from the detergent bottle and fill it with detergent designed specifically for use with pressure washers (Fig. 14). Fig.14 Spray lance snap Nozzle To disconnect a nozzle from the spray lance once the cleaning job is complete: 4. Turn off the pressure washer and shut off the water supply.Pull the trigger to release water pressure. 5.
6. When you have finished using the detergent injection system, insert the bottle detergent with fresh water. Siphon water at low-pressure for one minute to rinse the bottle until it is thoroughly cleaned. Fig.15 High Pressure Gun CAUTION! Failure to follow these cleaning Quick-Connect Adaptor instructions will cause the injection system to become clogged and inoperable.
Fig.16 i) The 0º intense-jet nozzle (red) is an extremely powerful nozzle that delivers a high-pressure, pencil- point jet stream. It is used to cut heavy dirt deposits in a small, concentrated area. It is ideal for dissolving stubborn substances, like tar and grease spots on concrete, or for removing caked mud from equipment. Use this nozzle to clean hard-to-reach areas including the facades of 2-story buildings or the undersides of lawn mowers and tractors.
Storage 1. Storage the trigger gun and spray lance on the holders(Fig.17). 2. Hang the power cord on (7) and high pressure hose on (10). • Store the pressure washer indoors in a dry, covered area where it is not subject to adverse weather conditions. • It is important to store this product in a frost-free area. Fig.17 • Always empty water from all hoses, the pump, and the detergent bottle before storing.
Maintenance CAUTION! Before working on the pressure Fig.21 washer, disconnect the plug from the power supply socket. 1. To ensure good performance, check and clean the water inlet filter (Fig. 19). Remove the filter and rinse with water to prevent any foreign matter from clogging the pump (Fig. 20). Fig.19 Garden hose adaptor water inlet filter Fig.20 water inlet filter 3. Remove additional debris by back flushing water through the nozzle and spray lance.
Troubleshooting Problems Possible Cause Possible Solution Machine refuses to start Faulty receptacle Try another receptacle The fuse has blown Replace the fuse Unplug other appliances Faulty extension cable Try without the extension cable The pump is drawing in air Valves dirty, worn or sticking Check that hoses and connections are airtight. Contact your service center The water supply is not sufficient Pump seals worn Increase water pressure, check for blockages and / or change the large pipe.
Limited 2 year warranty Electric pressure washer This Realm® product is warranted by Realm Import And Export (USA) INC. to the original purchaser for two years against defects in workmanship and materials when used for normal residential purposes. The defective product will be replaced or repaired at no charge in either of two ways, and subject to the conditions, limitations, and exclusions noted below. Limitations ·Electric motors and pumps carry a two (2) year warranty.
WEEE - Waste of Electric and Electronic Equipment The symbol on the product or on its packing indicates that this product may not be treated as household waste. Instead it shall be handed over. To the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.