am pi re
Contents Welcome To DVS.................................................... 2 Setting Audio CH ............................................. 14 Setting Mirror ON/OFF...................................... 15 Safety Instructions................................................. 2 Setting Reverse ON/OFF .................................. 15 CAUTION .............................................................. 2 WARNING ............................................................. 2 Setting Language ......
Operating Instructions Welcome to DVS ‧Thanks for purchasing DVS Center Armrest Monitor with MMD / USB function. This manual will help you use the exactly features of your new monitor. ‧Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference. Safety Instructions Be sure to observe the following instructions and precautions to ensure safe using of this monitor.
Operating Instructions Using the remote control PRECAUTIONS Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference. Personal Safety ‧The back seat passenger must fasten the seatbelt while operating this monitor. ‧Do not insert the USB while driving. Failure to do so may result in personal injury. Temperature Do not operate your unit in ambient temperature above +60°C (+140°F) or below 0°C (+32°F).
Getting St arted Correct Handling ‧Do not drop the disc while handling. ‧Hold the disc so you will not leave fingerprints on the surface. ‧Do not affix tape, paper, or gummed labels to the disc. ‧Do not write on the disc. INCORRECT Monitor Function Overview 7 8 9 10 4 6 CORRECT 5 3 2 1 Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the player to skip.
Getting St arted When Using the Remote Control Remote Control Function Overview When you use the remote control for the first time, pull the plastic tape before using the remote control. Plastic Tape Battery Replacement 1 . Opening the battery case. Pull up the battery tray. 2 . Replacing the battery. (CR-2025) CAUTION ‧Point the remote control at the remote sensors within 2 meters.
Getting St arted 1 POWER Switch the monitor power ON/OFF 2 OSD MENU 16 REPEAT RPT. Select the desired repeat mode. (1) DVD Disc: Chapter OSD Title REP. ALL OFF Enter or exit the on-screen display menu system. (2) CD/VCD Disc: 3 Repeat 1 EJECT DISK REP. ALL Repeat OFF Stop playback and eject the disc. 4 FM Transmisor FM Switch the FM ON/OFF. 17 MUTE MUTE Disable or enable audio output. VOL 5 DVD / USB USB/DVD Switch the DVD/USB mode.
Ba sic Operations Turning Power ON/ OFF Audio Mute Function The power state of the monitor will not be memorized when Ignition/ACC is turned off. When Ignition/ACC is turned back on, the monitor returns to OFF. Remote Control Front Control Keys 1. Press to turn ON. 2. To turn off the power, press and hold ‧While the power is ON, press Mute function. MUTE Press to turn the Mute function ON and OFF. MUTE Adjusting the Volume again.
MMD Operations Turning FM ON / OFF (Option) 1. Press to turn on the FM transmitter. 2. While FM is ON, press and to select FM desired FM frequency. 3. To turn off the FM, press FM again. ‧FM frequencies between 87.7MHz to 88.9MHz. Switching DVD / USB mode (DVD Only) 1. Press to change DVD mode or USB mode. USB/DVD CAUTION Do not use USB while driving your vehicle. Always stop the vehicle in a safe location before performing these functions.
MMD Operations Video Menu 1. Press 2. Press OSD to display Video Menu. to select the desired item, and then press OSD again to confirm a selection. ‧The video menu on DVD mode will be different with AV2 and AV3 mode. For details, refer to “MONITOR SETUP” on Page13~15. Stopping Playback (PRE-STOP) 1. Press during playback.“PRE-STOP ” is displayed, and playback pauses. That position is stored in memory. 2. Press in the PRE-STOP mode to return to normal playback.
MMD Operations Switching the Audio Tracks DVDs can have different audio tracks. These alternate tracks can be switched during playback. 1. During playback, press . The sound switched between the alternate audio tracks recorded on the disc each time the button is pressed. AUDIO ‧The selected alternate track becomes the default setting every time the power is turned on or the disc is replaced. If the disc does not Include that track, the disc’s default language is selected instead.
MMD Operations Displaying the Disc Status Slow Motion Playback Use the procedure described below to display the status (title number, chapter number, etc.) of the currently playing DVD/VCD/CD on the monitor screen. Slow allows you to select different slow playback modes for a VCD / DVD during playback. 1. During playback, press DISPLAY. 8 The playback status is displayed. 2. The playback status display closes when DISPLAY is pressed again. 8 1.
USB Operations CAUTION ‧Not all function will operate for every formats. See the individual USB’s instructions for details on the features supported. ‧Do not use USB while driving your vehicle. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in serious injury or an accident. ‧If you try to perform an invalid operation (based on the type of disc being played), the message “INVALID KEY” will be displayed on the monitor screen.
Monitor Se tup Adjusting Picture The video menu on DVD mode will be different with AV2, AV3 and AV4 mode. Adjusting the Bright 1. Press button on the remote control. OSD The picture setting menu is highlighted. ‧Each source is independently adjustable. ‧Make adjustments within 10 seconds, otherwise the OSD (On Screen Display) will turn off automatically. 2. Press . OSD or to confirm a selection.
Monitor Se tup Adjusting the Color Density (AV2/AV3 only) 1. Press button on the remote control. The Setting Audio Mute ON/ OFF 1. Press button on the remote control. The OSD picture setting menu is highlighted. OSD 2. Press picture setting menu is highlighted. 2. Press OSD or to select COLOR, then press to confirm a selection. or to select MUTE, then press to confirm a selection.
Monitor Se tup Setting Mirror ON/ OFF 1. Press button on the remote control. The OSD picture setting menu is highlighted. 2. Press OSD or to select MIRROR, then press to confirm a selection. Setting Language 1. Press button on the remote control. The OSD picture setting menu is highlighted. 2. Press OSD ENGLISH VIDEO MENU BRIGHT CONTRAST COLOR TINT MUTE AUDIO CH MIRROR REVERSE LANGUAGE RESET EXIT ON / OFF 3. Press or 3. Press 4.
MMD Se tup DVD Setup Operation ■ Setting the System (default : Auto) Broadcast TV System can be manually switched. 3. Press The following steps 1 to 2 are common to each of the DVD settings described here. Refer to each section for details. 1. Press and hold or PAL / AUTO. 4. Press ENTER to save adjustment. SYSTEM SETUP SETUP on the remote control. The setup menu appears on the monitor. SYSTEM SCREEN SAVER SCREEN TYPE PASSWORD RATING DIVX [R] VOD DEFAULT EXIT SETUP 2.
MMD Se tup ■ Setting Password There is not original password. Language Setup 3. Press + Number key pad to setup OSD Language, Audio Language, Subtitle Language and Menu Language are adjustable. to save adjustment. ‧The Factory setting of the OSD language is ENGLISH. 0 password. 4. Press ENTER ‧This function can be performing when the player is during stop. 1. Press button on the remote control. The setup menu appears on the monitor. SETUP 2.
MMD Se tup ■ Setting Subtitle Language (default : Chinese) 4. Press or to select desired language. ‧There are 7 kinds of languages can be chosen. (Chinese, English, Japan, French, Spanish, Portuguese, German.) 5. Press ENTER to save adjustment. LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG EXIT SETUP CHINESE ENGLISH JAPAN FRENCH SPANISH PORTUGUESE GERMAN OFF Audio Setup Down Mix, Dynamic Range and Down Sample are adjustable. 1. Press SETUP button on the remote control.
Installation and Connections Before installing or connecting the unit, please read the following and page 2~4 of this manual thoroughly for proper use. WARNING: Make the correct connections. Failure to make the proper connections may result in fire or product damage. CAUTION: The back seat passenger must fasten the seatbelt while operating the unit. Use only in cars with A 12 volt negative ground. (Check with your dealer if you are not sure.
Installation and Connections Parts Indication 1. LCD Monitor 2. USB Port 3. Disc-In Solt 4. Signal Cable (Blue) 5. Antenna (Option) 6. Signal Cable (Black) 7. VGA Cable (Option) 8. Back Cover Of Transverse Axle 9. Front Cover Of Transverse Axle 10. Bracket Arm 11. Iron Plate 12. A Type Plastic Adapter (for BMW 09 X5/X6) 13.
Installation and Connections Let the power cables and antenna pass 3 through the holes separately. (Figure 3) BMW’09 X5/X6 Antenna G type bracket Power Cable Using A type plastic adapter (Figure 3) Fix the unit and mounting plates by 4x15 4 screws. (Figure 4) Installation Step Remove the original cover and rear air1 conditioning outlet from the console box. (Figure 1) Mounting Plate 4×15 screws (Figure 1) (Figure 4) Finally, put the air-conditioning outlet back to 5 the console box.
Installation and Connections 2 Choosing suitable cable location General Installation Using mark sticker sticks in the suitable installation position, and then starts drilling one to two M12 O holes (Signal cable holes)and four M3O holes (Fixed holes) (Figure 2) Front Installation M12O M3O Mark Sticker Attention: >> Limitation: A.The width of the console box needs at least 17cm. B.The height on the top of the air-conditioning outlet needs at least 5cm.
Installation and Connections 2 Choosing suitable cable location. General Installation Using mark sticker sticks in the suitable installation position (Figure 2-1), and then starts drilling one or two M12O holes (Signal cable holes) and four M3O holes (Fixed holes) (Figure 2-2) Back Installation Mark Sticker (Figure 2-1) (Figure A) Attention: >> Limitation: A. The width of the console box needs at least 17cm. B.
Installation and Connections How to folding Front Installation 1. Normal usage. Back Installation 1. Normal usage. 2. Let the monitor turn 180 degrees clockwise. 2. Folding forward the monitor to complete folding. 3. Folding back the monitor to complete folding.
Installation and Connections Connections AV Connectors Yellow Video Input Connector This connector is used in combination with the video inputs of other video products (AV head out or TV Tuner). Black White(L) Red ( R) Green / Yellow Audio Input Connectors These connectors are used in combination with a head unit or TV Tuner with audio output connectors. Video Output Connector This connector is used in combination with the video inputs of other video products (AV head unit or LCD monitor).
Installation and Connections System Connections Multi Media Station TV Tuner AV Input V R L AV Output (Blue) V V AV Output R R L L V L L ( )GND (Black) (Red) R R Power Filter L V V (Black) Body ( ) R AV Input (Black) (+)ACC (Red) ACC (Yellow) AV 3 BATT (Yellow) Battery Center Armrest Monitor (Figure 1) AV Input AV 3 (As Figure 1) V V V R R R L L L NoteBook Signal Cable (Blue) Antenna (Option) Signal Cable(Black) AV Output (Blue) Game Player AV Input (Black)
Information Accessories Screen Bracket Arm x1 Screws (F⊕4×15) (For A Type Adapter) A Type Plastic Adapter (For BMW09 X5/X6) x1 Mounting Plate (For A Type Adapter) B Type Plastic Adapter x1 Screws (F⊕5×25) x1 Signal Cable (Blue) ER X FI LT BO OU T IN x4 Signal Cable (Black) x2 x4 Remote Control AV3 Cable x1 Mark Sticker O E D R S TU R ZO 1 N O M T IT IM 4 D 0 M 2 R LE E A 7 S LO W 3 A 8 R D Y LA V P /D IS B D 5 S FM -B U N D M A TU 6 E O S N G P
Information General Specifications DISPLAY SCREEN Size / Model 8” / TH080M 10.2” / TH102M Width 177mm 225mm Height 99mm 136mm Aspect Ratio 16:9 16:9 Transparent type TN Transparent type TN Liquid Crystal Display Liquid Crystal Display TFT-LCD, Active Matrix TFT-LCD, Active Matrix 800(W) × 480(H) × 3 800(W) × 480(H) × 3 1.152M pixels (VGA) 1.152M pixels (VGA) Effective Number of Elements 99.9% or more 99.
Information Troubleshooting CAUTION If you encounter a problem, please turn the power off, then on again. If the unit is still no functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized dealer. No function or display. Vehicle’s ignition off.
Information Image stops sometimes. Disc is scratched. - Replace with an non-scratched disc. Picture is unclear or noisy. Disc is being fast-forwarded or fast-reversed. - The picture may be unclear, but this is normal. Vehicle’s battery power is weak. - Check the battery power and wiring. (The unit may malfunction if the battery power is under 11 volts with a load applied.) Monitor’s fluorescent tube is worn out. - Replace the monitor fluorescent tube. Image stops sometimes. Disc is scratched.