TM 1
What’s in the Box? • 1 Quad View Digital Wireless Monitor with Cigarette Lighter Adaptor • 1 CCD Wireless Backup Camera with Power Cable • 1 Extendable Suction Cup Mount for Monitor
Table of Contents Introduction....................................................................................................4 Safety Information ...................................................................................5-7 Before Beginning Installation....................................................................8 Installation Guide..........................................................................................9 Pairing ......................................................
Introduction Congratulations on purchasing a Rear View Backup Camera Sys- tem. With this manual you will be able to properly install and op- erate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already ex- ists in your vehicle. The Backup Camera System should not be used as a substitute for the standard rear view mirror or for any other mirror that exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
Safety Information INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. Step 1: Choose the monitor and camera locations. Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm) hole should be drilled for passing camera cable through vehicles walls.
Installation Guide We recommend doing a benchmark test before installation to insure that all components are working properly. SYSTEM COMES PAIRED. • But if there is no image on monitor, your system is NOT paired and needs to be paired. (see page 10) Camera Connection: • Locate the clearance lights wiring on your vehicle. You may need to remove the interior panel in order to locate. Connect the power cables for camera: Red wire to light's positive; Black wire to chassis ground.
Pairing 1. Press MENU on monitor and it will bring you to “camera settings” screen. (see screen 1) 2. Press MENU 2nd time you will see “pairing” option. (see screen 2) 3. Press MENU 3rd time and camera 1 is selected. (see screen 2) Select camera 2 (Back-up camera), using the up/down arrow. Screen 1 Screen 2 4. Remove screw from back of the camera to reveal “Pair Button” (See diagram page 12). 5. Press MENU a 4th time to begin pairing process.
System Operation • To turn on the monitor, press “POWER ON” button. • To get to Main Menu, press “MENU” 1 time • To get to Camera Settings, press “MENU” 2 times, use arrows to get to System Settings. Camera Settings: To adjust Pairing, Activation, Brightness or Volume • Use arrows to reach desired item.
Operational Diagram CAMERA SELECTION DOWN ARROW MENU/ SELECTION BUTTON UP ARROW POWER ON / OFF ROTATION IMAGER (Exit when in MENU mode) CAM t t MENU REV PAIR BUTTON QUAD MONITOR CAMERA INLINE FUSE RED POSITIVE 12 BLACK GROUND REAR VIEW SAFETY
Installation Diagram On Select Models Figure 1.1 Figure 1.2 Figure 1.3 Figure 1.
Monitor Dimensions 7” Menu/ Power Selection Camera Down Up On/Off Button Selection Arrow Arrow 14 Rotation Imager (Exit in Menu Mode) 5.
Monitor Speciifications TFT LCD Digital Monitor Screen Size 7” Dot Resolution 800H x 3 (RGB) 480V Display Brightness 400cd/m2 Video Input 4 channel Display Format Viewing Angle Video Source Power Supply Power Consumption 16:9 / 500:1 U:50° / D:60° / R:70° 1Vp-p, 75Ω DC 12V(+/- 10%) 5W Operating Temperature -30°C ~ +80° C Overall Dimensions 7”L x 5”H x 1”D Video System Auto NTSC/PAL Weight 400G Dot Pitch 0.192H x 0.
Camera Dimensions 3.
Camera Camera Specifications Picture Elements Gamma Correction Image Sensor Lens View Angle Sync System Infrared distance Usable Illumination 1/4” Sharp® Color CCD 250,000 pixels r=0.45 to 1.0 480TV lines 2.1mm 130° Internal Synchronization 50 Feet (12 Infrared) 0 Lux (IR On) Power Source DC 12V (+/- 10%) Electronic Iris 1/50, 160-1/100,000sec S/N Ratio Video Output IR Switch Control More than 48dB 1Vp.
Splitting Installing & Splitting Embedded Monitor Installing sun shield: Put shade cover on the display. Installing back cover: Put the monitor with shade cover in the back cover (only for embedded monitor) Splitting back cover: Hold monitor with 2 hands and detach with fingers, as indicated by arrows. (only for embedded monitor) Splitting sun shield: Take the monitor with the left hand and detach with right hand as indicated by the white arrow.
Positioning Rear Camera Positioning Reverse With Confidence 19
Troubleshooting NOTE: VERIFY THE SYSTEM IS PAIRED Monitor Display Blue Screen & Displays No Signal • Do a hard reset, unplug all • Check to ensure that the concables and power cables leave nection to the camera is tight. out for 1 minute and then re-connect them.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
