Version Number: Mig210-20201221A1 Operation Manual Reboot MIG210 welding machines adopts the latest pulse width modulation (PWM) technology and insulated gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as to replace the traditional Transistor transformer with the medium frequency transformer. its characterized with portable, small size, light weight, low consumption and etc.
Version Number: Mig210-20201221A1 wire feeding speed are automatically matched. Only when the deviation is too large, it can be adjusted appropriately. Inductance adjustment: If the splash is too large or the welding pool is not deep enough, it can be adjusted to a larger value, otherwise it can be smaller. 7. Positive Terminal Positive Terminal. Welding current flows from the power source via heavy duty bayonet type terminals.
Version Number: Mig210-20201221A1 8 Conductive tip0.8 3 Spare parts, need to be replaced frequently, please keep inventory Conductive tip1.0 3 Spare parts, need to be replaced frequently, please keep inventory Porcelain nozzle 3 For flux-cored welding wire,Spare parts need to be replaced frequently, please keep inventory Wire feed wheel 1 V-shaped wire feed wheel adapts to solid welding wire 0.8mm/1.0mm， 1 The gear wire feed wheel is suitable for flux-cored welding wire diameter 0.8mm/1.
Version Number: Mig210-20201221A1 Part 3: Simple test for powering on the machine Reboot MIG210 Welding machines will be subjected to strict various tests when they leave the factory to ensure that each welding machine that reaches the user is of high quality, because our machine has to go through tens of thousands of kilometers of long-distance transportation from the factory to the delivery to you.
Version Number: Mig210-20201221A1 Part 4: Technical specifications TYPE RBM2100 RBM2100 Input power voltage (V) 1phase AC110V，50/60Hz 1phase220V，50/60Hz Rated input current (A) 45.1 30.6 Rated power capacity (KVA) 3.5 4.2 Current adjustment range (A) mig:30-140 mma:30-140 mig:30-175 mma:30-140 Welding thickness (mm) >1.0 >1.0 Voltage adjustment range (V) 15-22 15-24 No-load voltage (V) 55±5 55±5 0.8/1.0 0.8/1.0 Rated duty cycle 60% 60% Efficiency (%) 85% 85% Power factor 0.
Version Number: Mig210-20201221A1 2、 Connect welding holder and ground clamp. 3、 To adjust the current, only the current can be adjusted. Note: 1) The welding rod specification supported by Reboot mig210 is below 4.0(5/32in), usually 2.5(3/32in) and 3.2(1/8in). European style generally uses E6013, American style generally uses E7018, and stainless steel generally uses ER308. 2) It supports welding of 1-8mm(1/64-5/64in) carbon steel and 1-5mm(1/64-7/32in) stainless steel. Aluminum can not be welded.
Version Number: Mig210-20201221A1 5) It is normal for novices to have adhesion during the welding process, and you can try to friction arc to avoid adhesion. 6) Suitable for ordinary welding rods, such as 7018, 6013, etc., but not suitable for special welding rods, such as 7010, 7011 Possible problems 1) There is no arc, check the ground wire to connect the workpiece to ensure that there is no rust, paint or other coatings on the workpiece.
Version Number: Mig210-20201221A1 3、Connect MIG gun and ground clamp. 4、Install wire spool 0.030”(0.8mm)/0.040”(1.0mm)diameter 8”(200mm 5kg)wire spool 4”（100mm 1kg）wire spool 5、Set drive roll Face the side marked 0.030” away from the machine Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040” (1.0mm) to match the corresponding wire diameter.
Version Number: Mig210-20201221A1 2. Gas welding requires the use of V-type wire feed wheels, which are suitable for ordinary carbon steel welding wire and stainless steel welding wire, and need to use CO2 gas or CO2 and AR gas mixture. 6、Feed wire and set pressure The pressure should not be too loose, too loose will cause the welding wire to slip and the wire feeding is unstable, and too tight will cause the welding wire to slip and deform.
Version Number: Mig210-20201221A1 2. Attach hose and regulator to gas bottle. 9、Installation of welding torch. The welding wire should be extended outside the European central socket, and then install the welding torch. The wire guide tube and contact tip of the welding torch need to match the welding wire. Press and hold the torch switch wrench for more than 3 seconds to not weld. This is fast wire feeding. Let the welding wire be quickly delivered to the gun head.
Version Number: Mig210-20201221A1 4. “V”，If you are not satisfied with the automatic adjustment of the machine, you can fine-tune the voltage (when the current and wire feeding speed are unchanged), "inductance", during the welding process, it feels that the welding pool is not deep enough and the splash is too large, so you can adjust it appropriately . 13、With contact tip 1/4” from metal, depress trigger completely to initiate arc 14、To replace the welding wire.
Version Number: Mig210-20201221A1 Note: 1. Nozzle, 2. Conductive nozzle. They are wearing parts and need to be replaced frequently, please keep inventory. 19. The guide wire tube, it is best to equip a spare part because it may damage the accessories. Note: 1） Please strictly follow the picture instructions to connect, otherwise it will not be possible to solder. 2） Solid core welding wire supports 0.8, 1.0, 0.6 (need to purchase welding wire, wire feed wheel and contact tip).
Version Number: Mig210-20201221A1 intelligently matches the best welding parameters according to different specifications of welding wires to achieve the best results. 4、Connect MIG gun and ground clamp. Flux-cored wire Note: No need to use gas cylinder and gas meter 5、Install wire spool 0.030”(0.8mm)/0.040”(1.
Version Number: Mig210-20201221A1 5、Set drive roll Face the side marked 0.030” away from the machine Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040” (1.0mm) to match the corresponding wire diameter. 2.
Version Number: Mig210-20201221A1 8、Installation of welding torch. the welding wire should be extended outside the European central socket, and then install the welding torch. The wire guide tube and contact tip of the welding torch need to match the welding wire. Press and hold the torch switch wrench for more than 3 seconds to not weld. This is fast wire feeding. Let the welding wire be quickly delivered to the gun head. 9、 Remove consumables and depress trigger until wire comes out.
Version Number: Mig210-20201221A1 11、Adjust wire feed speed ，current and voltage 1.Choose MIG, MMA, LIFT-TIG working mode 2.Choose welding wire diameter 0.8/1.0mm, choose airless (Flux-cored wire). 3. The machine has a unified function, so just adjust this knob the the welding current, voltage and wire feeding speed are adjusted automatically at the same time. 4.
Version Number: Mig210-20201221A1 14、Torch structure: Note: 1. Nozzle, 2. Conductive nozzle. They are wearing parts and need to be replaced frequently, please keep inventory. 19. The guide wire tube, it is best to equip a spare part because it may damage the accessories. Note： 1) Please strictly follow the picture instructions to connect, otherwise it will not be possible to solder. 2) The flux-cored welding wire supports 0.8, 1.0. 3) The machine can install 5kg(11lb) and 1kg(2.
Version Number: Mig210-20201221A1 stop working for a few minutes, let the machine cool for a period of time, and automatically recover. If the air cools for more than 10 minutes, the machine does not automatically recover, please shut down and restart. 6) If you have any questions, please contact us at service@mirthtek.com.
Version Number: Mig210-20201221A1 3、 Adjust the current, only the current can be adjusted。 4、 WP17V Structure of welding torch NOTE:tig torch and accessory are not included Remark: 1. ceramic nozzel, 2 .tungsten collet, 3. tungsten collet body, 4 .short back cap, 5. long back cap.
Version Number: Mig210-20201221A1 2) This machine is not a professional high-frequency arc starting argon arc welding machine, it is only a LIFT TIG contact arc starting or friction starting. 3) Need to use TIG, wp17v torch, this torch is not included, you need to buy it yourself 4) Support welding material material, carbon steel, stainless steel, alloy steel, aluminum can not be welded.
Version Number: Mig210-20201221A1 welding shape is good, and there is less spatter. 6. Metal high-power wire feeding structure, strong wire feeding force and stable wire feeding. 7. The thick output connection wire of all copper, the welding effect is better. 8. Thicker radiator, better heat dissipation effect. Part 5:Trouble Shooting Observe all Safety Guidelines detailed throughout this manual PROBLEMS (SYMPTOMS) POSSIBLE CAUSE OUTPUT PROBLEMS Major physical or electrical damage is evident.
Version Number: Mig210-20201221A1 Part 6: Welding parameter settings This translation comes from Google Translate. If you are interested in translating professional local languages, please contact us at service@mirthtek.com, we can pay for it.
