Assembly Instructions

ManualsBrandsRebrilliant ManualsStorage & OrganizationCastaneda 8 Drawer Rolling Storage Chest

ASSEMBLY INSTRUCTIONS

6+2 Drawer Wide Roll Cart

Medium Pine Finish

1/8

IF YOU CALL, PLEASE HAVE ON HAND:

• PRODUCT NAME AND STOCK NUMBER

• WHEN AND WHERE THE UNIT WAS PURCHASED

• P.O. NUMBER FROM THE BOTTOM OF THIS PAGE

IF WE ARE BUSY HELPING OTHER CUSTOMERS, PLEASE LEAVE YOU NAME AND NUMBER

TO RECEIVE A RETURN CALL.

YOUR RETAILER MAY ALSO PROVIDE SERVICE OR PARTS.

HELPFUL OVERALL:

• SAVE THESE INSTRUCTION SHEETS AND THE BOX UNTIL YOU ARE SATISFIED WITH THE ASSEMBLY.

• DO NOT GLUE THE PARTS OF THE UNIT TOGETHER UNLESS YOU HAVE TESTED THE ASSEMBLY FIRST.

• PERFORM THE ASSEMBLY ON A CLEAN HARD SURFACE USING THE FLATTENED CARTON OR A TOWEL

TO PROTECT THE SURFACE AND THE FINISH OF THE UNIT. DO NOT ASSEMBLE ON CARPET.

NOTICE: THE WRITTEN INSTRUCTIONS CONTAINED HEREIN ARE COPYRIGHTED.

CUSTOMER SERVICE AND REPLACEMENT PARTS:

FOR FASTER SERVICE ON PARTS OR HELP, PLEASE GO TO OUR WEBSITE

OR CALL TOLL FREE FOR ASSEMBLY QUESTIONS.

THANK YOU FOR YOUR PURCHASE AND WELCOME !

Summary of content (8 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS 6+2 Drawer Wide Roll Cart Medium Pine Finish CUSTOMER SERVICE AND REPLACEMENT PARTS: FOR FASTER SERVICE ON PARTS OR HELP, PLEASE GO TO OUR WEBSITE OR CALL TOLL FREE FOR ASSEMBLY QUESTIONS. IF YOU CALL, PLEASE HAVE ON HAND: • PRODUCT NAME AND STOCK NUMBER • WHEN AND WHERE THE UNIT WAS PURCHASED • P.O. NUMBER FROM THE BOTTOM OF THIS PAGE IF WE ARE BUSY HELPING OTHER CUSTOMERS, PLEASE LEAVE YOU NAME AND NUMBER TO RECEIVE A RETURN CALL. YOUR RETAILER MAY ALSO PROVIDE SERVICE OR PARTS.
PAGE 2
*.
PAGE 3
A Dowel 8.0 x 30mm 12 B Screw 3.0 x 25mm 64 C Screw 4.0 x 30mm 12 D Drawer Runner 16 (Ea) Caster and (Eb) Caster Insert Pair E Nail 1.5 x 19mm F 04 44 TIP: DOWELS (PART A) VARY EVER SO SLIGHTLY. IF A DOWEL (PART A) IS LOOSE WE PREFER YOU CALL OUR TOLL FREE NUMBER FOR ADDITIONAL DOWELS VS GLUING THE DOWEL. 1 IF YOU CHOOSE TO GLUE THE PARTS, COMPLETELY TEST THE ASSEMBLY FIRST. WE DO NOT SUPPLY GLUE.
PAGE 4
1 PREPARE PARTS FOR ASSEMBLY • PUSH THE DOWELS (PART A) INTO THE EDGES OF THE FOLLOWING PARTS, AS SHOWN: (PART 2) RIGHT SIDE (PART 3) LEFT SIDE (PART 6) BACK CASTOR SUPPORT (PART 7) FRONT CASTOR SUPPORT Perform the entire assembly on a clean, hard surface using the flattened box or a towel to protect the surface and the unit's finish. DO NOT assemble on carpet. A Carpet creates too much bounce making assembly difficult and could lead to damage of the parts.
PAGE 5
2 ATTACH THE SIDES TO THE CROSSBARS C ATTACH ONE SIDE FIRST AND THEN THE OTHER. • DO NOT STAND LEFT SIDE (PART 3) UP ON THE EDGE YET. TO EASE ASSEMBLY, LAY SIDE FLAT ON THE FLOOR, RUNNER SIDE VISIBLE. 2 • MATCH UP BACK CASTER SUPPORT (PART 6) AND FRONT CASTER SUPPORT (PART 7) AT DOWEL HOLES LOCATED AT THE BOTTOM OF SIDE. c 5 c 3 c c • PLEASE CHECK THAT THE DISTANCES MATCH TO THE SQUARE DIAGRAM. 7 c • SECURE BACK CASTER SUPPORT (PART 6) TO THE LEFT SIDE (PART 3) USING SCREW (PART C).
PAGE 6
4 ATTACH THE BACK PANEL F F Use all back panels nails. Evenly spaced, they help make the unit strong. F F F F F F F • HOLD THE (PART 4) BACK PANEL IN THE GROOVES INSIDE THE UNIT´S SIDES. F F F • CHECK THAT THE UNIT IS SQUARE. F • SECURE THE (PART 4) BACK PANEL USING THE (PART F) NAILS. F 4 F F F F F F F=28 F F F F F • ALSO MAKE SURE THE BACK PANEL FITS IN THE GROOVE AT THE BACK OF THE TOP.
PAGE 7
6 ASSEMBLE THE LARGE DRAWERS 13 • LINE UP THE BOTTOM EDGE OF THE LARGE DRAWER SIDE (PART 13) WITH THE BOTTOM EDGE OF THE LARGE DRAWER FRONT (PART 12). 12 • JOIN THE PARTS USING TWO SCREWS (PART B) AS SHOWN IN THE DIAGRAM. 13 NOTE: THE SCREWS' SHARP TIPS ARE SELF TAPPING, SO THE DRAWER FRONT DOES NOT NEED A PILOT HOLE. THE SHARP TIP STARTS THE HOLE, AND THE SCREW THREADS WILL SECURE THE PART IN PLACE FOR A TIGHT FIT. • REPEAT ON THE OTHER SIDE OF THE DRAWER.
PAGE 8
COMPLETED ASSEMBLY: THANK YOU FOR YOUR PURCHASE, AND WELCOME ! USE AND CARE INSTRUCTIONS: CARE INSTRUCTIONS: • NORMAL USE: WIPE WITH A CLEAN CLOTH. • WHEN NEEDED TO CLEAN SCUFFS:WIPE CLEAN WITH A SLIGHTLY DAMP CLOTH AND A MILD CLEANER. THEN WIPE DRY WITH A CLEAN CLOTH. • IF YOU OIL OR WAX THIS FURNITURE, IT WILL MORE QUICKLY DEVELOP A PATINA AND DARKEN. USE: MULTI-PURPOSE MOBILE STORAGE UNIT FOR HOME, OFFICE, CRAFT ROOM, KITCHEN, OR GARAGE.