ASSEMBLY INSTRUCTIONS TWO DOOR WALL CABINET WHITE ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of the small parts. Care should be taken in unpacking and assembling this item to keep the small parts away from children. WARNING Young children can be seriously injured or killed, if furniture tips over. Don’t use this item for a TV stand. Use angle-braces or anchors to secure furniture to the wall.
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 50 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS AND A TOTAL OF 50 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF AND 50 POUNDS TOTAL WEIGHT THE SHELF MAY FALL FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO PARTS QTY DESCRIPTION 1 1PC TOP BOARD 2 1PC LEFT SIDE PANEL 3 1PC RIGHT SIDE PANEL 4 1PC RIGHT DOOR 5 1PC LEFT DOOR 6 1PC REAR TOP BAR 7 1PC CROSS BAR 8 1PC SHELF 9 1PC BOTTOM BOARD
NO PARTS QTY DESCRIPTION 10 1PC LOWER BACK BOARD 11 1PC TOP BACK BOARD 12 1PC MIDDLE BACK BOARD A 10PC CAM BOLT B 10PC CAM LOCK C 18PC WOOD DOWEL D 4PC METAL HINGE E 1PC MAGNET F 2PC MAGNET PLATE
NO PARTS QTY DESCRIPTION G 2PC KNOB H 2PC MACHINE SCREW 4x20mm J 22PC WOOD SCREW 3x10mm K 2PC SCREW 3x14mm BACK BOARD SCREW M 24PC 2.
STEP 1 STEP 1 1. Screw 4 cam bolts (A) into the pre-threaded holes on the top board (1) by using a Philips Screwdriver. 2. Insert 2 wood dowels (C) into the dowel holes on the top board (1). 3. Attach the Magnet (E) to the top board by insert 2 screws (K) through holes on magnet (E) then tighten to top board (1) by using a philps screwdriver. STEP 2 STEP 2 1. Screw 3 cam bolts (A) into the pre-threaded holes on the left side panel (2) by using a philips screwdriver. 2.
STEP 3 STEP 3 1. Screw 3 cam bolts (A) into the pre-threaded holes on the right side panel (3) by using a philips screwdriver. 2. Insert 7 wood dowels (C) into the dowel holes on the right side panel (3). 3. Attach 2 metal hinges (D) to right side panel (3) by insert 6 wood screws (J) through the holes on the metal hinges and tighten to right side panel (3). STEP 4 STEP 4 1. Insert 1 screw (J) through hole on the magnet plate (F) then tighten to right door (4) by using a philips screwdriver. 2.
STEP 5 STEP 5 1. Insert 2 wood dowels (C) into dowel holes on the lower back board (10). STEP 6 STEP 6 1. Attach the lower back board (10) to bottom board (9) by insert wood dowels (C) to the holes on the bottom board (9).
STEP 7 STEP 7 1. 2. 3. Insert 3 cam lock (B) into the cam lock holes on lower back board (10) and bottom board (9), make sure it forwards correctly. Attach rear top bar (6), shelf (8), bottom board (9) and lower back board (10) to left side panel (2) by insert cam bolts (A) into cam lock holes and insert wood dowel (C) into dowel holes on rear top bar (6), shelf (8), bottom board (9) and lower back board (10). Rotate cam locks (B) clockwise to secure 3 cam bolts (A) in place. STEP 8 STEP 8 1. 2. 3. 4.
STEP 9 STEP 9 1. 2. 3. Insert 4 cam locks (B) into the cam lock holes on the left and right side panel (2) (3), make sure it forwards correctly. Attach top board (1) to assembled unit by insert wood dowels (C) into dowel holes and insert cam bolts (A) into cam lock holes on left and right side panel (2) (3). Rotate cam locks (B) clockwise to secure 4 cam bolts (A) in place. STEP 10 STEP 10 1.
STEP 11 STEP 11 1. 2. Attach left door (5) to left side panel (2) by insert 4 screws (J) through the holes on the hinge (D) then tighten to the left door (5). Repeat above step to assemble the right door (4). STEP 12 STEP 12 1. 2. 3. 4. Place the drawing with hole position on the wall that you desire to hang the Cabinet. Drill 2 holes through the hole position on the drawing. Insert 2 plastic anchors (O) into the holes.
ENJOY YOUR NEW CABINET NOW ! Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct the hazard such as tightening of screws and taking any damaged parts away from the children.