OWNER’S MANUAL UNDERSINK ORGANIZER 2-pack
PARTS LIST Your Undersink Organizer should include the following parts. Please inspect box contents to ensure you have received all components. If you are missing any parts, need assistance with assembly or have questions, please contact Customer Service. Parts can also be requested online at our customer center You will need a Phillips screwdriver for assembly. A rubber mallet is also recommended.
INSTALLATION INSTRUCTIONS – In Cabinet STEP 1 Place CABINET MOUNTING TEMPLATE (G) inside your cabinet. Using a pencil, mark the location to install the CABINET SCREWS (F). G (1) • Note: To ease the installation you can pre-drill small holes at the marked locations. STEP 2 Identify LEFT & RIGHT SLIDES (B) & (C). • Note that the BACK end of each SLIDE (B) & (C) has a black tip and the FRONT end does NOT.
INSTALLATION INSTRUCTIONS – In Cabinet STEP 3 Align LOWER DRAWER (A) at the marked location and push it into the clips of the LEFT & RIGHT SLIDES (B) & (C). A (1) Installation Suggestion: With the LOWER DRAWER (A) resting on top of the clips, brace the top of the LOWER DRAWER (A) with one hand and, with a rubber mallet, lightly tap each bottom corner of the LOWER DRAWER (A) to secure the LOWER DRAWER (A) into the clips. STEP 4 Remove the black caps from 2 corner posts of the LOWER DRAWER (A).
INSTALLATION INSTRUCTIONS – On Wire Rack STEP 1 Identify LEFT & RIGHT SLIDES (B) & (C). • Note that the BACK end of each SLIDE (B) & (C) has a black tip and the FRONT end does NOT. Place SLIDES (B) & (C) on desired wire shelf. Make sure the FRONT of the SLIDES (B) & (C) is lined up with the FRONT of the shelf. B (1) C (1) Line up the slides along the wires in the wire shelf to ensure they are straight. Make sure the front edge of the WIRE DRAWER (A) lines up to the edge of the shelf so they are flush.
INSTALLATION INSTRUCTIONS – On Wire Rack STEP 3 With a Phillips screwdriver, secure the SLIDES (B) & (C) to the wire shelf by putting PLATE SCREWS (E) through the slots and fasten to the RACK PLATES (D). D (4) E (4) STEP 4 Attach the LOWER DRAWER (A) to the clips in the LEFT and RIGHT SLIDES (B) & (C) until it clicks into the clip.
INSTALLATION INSTRUCTIONS – On Wire Rack STEP 5 Remove the black caps from 2 corner posts of the LOWER DRAWER (A). Insert the 2 CONNECTORS (H) into the posts of the bottom basket. Place the UPPER DRAWER (I) on the connectors. H (2) I (1) Note: The UPPER DRAWER (I) can be placed on the right hand side or the left hand side.
SERVICE PARTS LIST Customer Service provides the following replacement parts: Description 1) Upper Drawer 2) Connector 3) Lower Drawer 4) Right Slide 5) Cabinet Screw 6) Template 7) Plate Screw 8) Rack Plate 9) Left Slide 10) Plastic Cap 1 2 10 9 3 4 7 8 5 7 6
WARNINGS 1. Read and understand all instructions. Failure to follow all instructions may result in injury and/or damage. 2. The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions or situations that may occur. The user must always be aware of their environment and ensure that they use the product in a safe and responsible manner. 3. Do NOT modify the product in any way.
PRODUCT REGISTRATION Thank you for purchasing a Undersink Organizer. In order to register your product and receive streamlined customer service, please fill out the following Product Registration Form and (1) fax the form (2) complete the Product Registration Form online or (3) scan and email the form. Include a copy of your original receipt with your submission.
LIMITED WARRANTY Undersink Organizer LIMITATION OF REMEDIES AND LIABILITY 10
CONTACT US QUESTIONS? NEED PARTS? WE ARE HERE TO HELP! Please feel free to contact us. There are no questions too small, or any problems too big. We’re committed to providing our customers with the highest level of service.
