Datasheet

ManualsBrandsRecom ManualsBoard Mounted DC / DC ConvertersDC/DC Converter 3 ... 17V 5V

www.recom-power.com

REV.: 3/2019 RPM-1

DC/DC Converter

Description

The RPM-1.0 series is a 1A non-isolated switching regulator power module with a full set of features

including adjustable output, sequencing, soft-start control, on/off control, and power good signals. The

ultra-compact module has a proﬁle of only 3.75mm, but with an efﬁciency of up to 99%, the device can

operate at full load in ambient temperatures as high as +107°C without forced air cooling. The package

is complete with 6-sided shielding for optimal EMC performance and excellent heat management.

1 Amp

Single

Output

RPM-1.0

Features

Power

Module

• High power density (L*W*H = 12.19*12.19*3.75)

• Wide operating temperature -40°C to 90°C

at full load

• Efﬁciency up to 99%, no need for heatsinks

• 6-sided shielding

• Thermally and EMI enhanced 25 pin LGA package

• Compact DOSA-compatible footprint

• Low proﬁle

www.recom-power.com/eval-ref-boards

EN55032 compliant

Selection Guide

Part Input Voltage Output Vout Output Efﬁciency Max. Capacitive

Number Range Voltage Adjust Range Current max. typ. Load

(1)

[VDC] [VDC] [VDC] [A] [%] [µF]

RPM3.3-1.0

(2)

3 - 17 3.3 0.9 - 6.0 1 94 - 99 800

RPM5.0-1.0

(2)

3 - 17 5 0.9 - 6.0 1 92 - 99 800

Notes:

Note1: Max. Cap Load is tested at nominal input and full resistive load

Notes:

Note2: add sufﬁx “-CT” for tube packaging for more details refer to “PACKAGING INFORMATION”

without sufﬁx, standard tape and reel packaging

1 Amp

Single

Output

RPM-1.0

Features

Power

Module

• High power density (L*W*H = 12.19*12.19*3.75)

• Wide operating temperature -40°C to +107°C

at full load

• Efﬁciency up to 99%, no need for heatsinks

• 6-sided shielding

• Thermally and EMI enhanced 25 pin LGA package

• Compact DOSA-compatible footprint

• Low proﬁle

Model Numbering

Speciﬁcations (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)

BASIC CHARACTERISTICS

Parameter Condition Min. Typ. Max.

Internal Input Filter capacitor

Input Voltage

Range

Buck mode

3.3Vout

5Vout

3.35VDC

5.05VDC

12VDC 17VDC

100% duty cycle mode

(3)

Vout= Vin - Vdrop

3.3Vout

5Vout

3VDC

3.35VDC

5.05VDC

Absolute Maximum Input Voltage

20VDC

Undervoltage Lockout (UVLO)

DC-DC ON

DC-DC OFF

2.6VDC

2.8VDC

2.7VDC

2.9VDC

2.8VDC

3.0VDC

Input Current nom. Vin= 12VDC

3.3Vout

5Vout

0.3A

0.45A

Quiescent Current

30µA

Internal Power Dissipation

3.3Vout

5Vout

0.27W

0.32W

continued on next page

Packaging

(2)

Output Voltage

max. Output Current

RPM__-1.0-__

Summary of content (9 pages)

PAGE 1
• High power density (L*W*H = 12.19*12.19*3.75) • Wide operating temperature -40°C to +107°C 90°C at full load • Efficiency up to 99%, no need for heatsinks • 6-sided shielding • Thermally and EMI enhanced 25 pin LGA package • Compact DOSA-compatible footprint • Low profile Features Power Module Description The RPM-1.
PAGE 2
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) Parameter Condition Output Voltage Trimming Min. Typ. Max. 0.9VDC (4) Minimum Dropout Voltage (Vdrop) (5) 6VDC 50mV/A Vin min. = Vdrop + Vout Minimum Load 0% without using soft start function/ power up using CTRL function Start-up Time 1.6ms 1.5ms Rise-time 1.4ms ON/OFF CTRL DC-DC ON DC-DC OFF Input Current of CTRL Pin DC-DC OFF Open or 0.
PAGE 3
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) OUTPUT VOLTAGE TRIMMING The RPM series offers the feature of trimming the output voltage over a range between 0.9V and 6V by using external trim resistors. The values for trim resistors shown in trim tables below are according to standard E96 values; therefore, the specified voltage may slightly vary.
PAGE 4
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) REMOTE SENSE +Vin +Vin RW1 +Vout +Vout +Sense Trim Rdown Rup GND GND GND GND The output voltage can be adjusted via the trim and sense functions. The maximum output voltage from Trim and Sense function combined is 5.5VDC. Derating may be required when using Trim and/or sense functions. RW1 ... wire losses + Rup ... trim up resistor Rdown ...
PAGE 5
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) To sequence multiple power module start-up times the power good (PGood) pin and the CTRL pin may be used. In below schematic, the RPM(n) starts after RPM(1) reaches its set output voltage and the power good signal is set to high which then enables RPM(n). After RPM(n) reaches its set output voltage, it enables RPM(n+1).
PAGE 6
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) PROTECTIONS Parameter Condition Short Circuit Protection (SCP) Value 50mW Short Circuit Input Current constant current mode without soft-start mode Over Current Protection (OCP) 75mA typ.
PAGE 7
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Standard designed to meet EN62368-1 Audio/video, information and communication technology equipment.
PAGE 8
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) Dimension Drawing (mm) Pinning information Function Description A1, A2 Vin Positive input voltage with respect to GND. Connect to a Vin plane for enhanced thermal performance C1 CTRL Active High: pull to GND to disable the device. Pull high or leave open to enable the device A5, B5 Vout Positive output voltage.
PAGE 9
RPM-1.0 DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated) PACKAGING INFORMATION Parameter Packaging Dimension (LxWxH) Packaging Quantity Type tape and reel tape and reel (carton) 330.2 x 330.2 x 30.4mm 355.0 x 350.0 x 50.0mm tube (“-CT”) 530.0 x 30.3 x 19.2mm tape and reel 500pcs tube (“-CT”) 30pcs Tape Width 24mm Storage Temperature Range Storage Humidity Value -55°C to +125°C non-condensing 95% RH max.