Manual

ManualsBrandsRECON ManualsCar264150 Backup Projector Lamps DIY

Page 1

In This DIY We Will Show You How To Install Recon Backup Lamps (part # 264150 To Run On A Separate Switch & In Reverse.

Please Note, There Are Many Ways of Installing These Lights, Including Wiring Methods, Wiring Connectors, And Other Variables

_________________________________________________

- Go Over The Parts Included In The Kit That You Received – Confirm All Items Are In The Box.

You Should Have

- 2 Projector Lamps

- 1 Switch

- Wire Harness

________________________________________________________

Tools Required:

A Good Assortment of Hand Tools are Recommended, Required Hand tools Are As Followed:

- Drill

- Drill Bit Set

- Phillips Bit

- DC Voltage Meter

- Screw Drivers Phillips & Flat Head (Small Flat Head)

- Wire Strippers & Crimper's

- Choice of Connectors +/- Soldering Tools

- Electrical Tape

Summary of content (7 pages)

PAGE 1
In This DIY We Will Show You How To Install Recon Backup Lamps (part # 264150 To Run On A Separate Switch & In Reverse. Please Note, There Are Many Ways of Installing These Lights, Including Wiring Methods, Wiring Connectors, And Other Variables _________________________________________________ - Go Over The Parts Included In The Kit That You Received – Confirm All Items Are In The Box.
PAGE 2
The Following Are Additional Components You'll Need To Get To Install Exactly As Indicated On These Instructions: • • • • • Insulated Terminal Connectors Heat Shrink Tubing Stranded LV Wire (Spec'd At Least At 20 Amp) 30A Relay (Auto 12V) 1N4005 Diode • • • • • 4 Stainless Bolts 4 Stainless Washers 4 Stainless Lock Washers 4 Stainless Nuts At Least 15ft of Wire Loom ______________________________________________________________________________ Projector Layout & Drilling.
PAGE 3
• • Find A Center Point To Measure Off Of. Now, Make Two Marks Per Projector Lamp - 7/8" Apart • • With The Holes Laid Out, Drill Using Proper Drill Bit (According To Bolt Diameter) You Can Now Mount The Projectors, Flip Down The Bracket To Allow Hardware To Slip In (Make Sure The Bolt Head Is On The Bottom Side) • With The Hardware Installed - Flip The Projector Up and Tighten The Hinge.
PAGE 4
Tie Into Backup Lamps & Wire Projectors • Locate The OEM Wires Going To Your Tail lamp - Peal The Wires Out From The Loom • • With A Multi Meter, Find Out Which Wire Powers Your Reverse Light Bulb Cut Out A Section of Wire To Solder To & Solder To The New Wire Labeled "Reverse Light" • • Tape and Cover Splice With Loom With The Supplied Wire Harness (The One That Came With The Recon Projectors) Cut The White and Black Wires Designed To Wire Up The Projectors - Approx. Half Way.
PAGE 5
• • Connect Harness To Projectors Connect Harness To A Solid Ground (To Prevent Rusting, It Is Recommended To Spray Terminals With Rust Blocking Agent) • Finish Running Loom Around Wires, Tape And Zip Tie Everything Up. The Rear Is Now Complete. Onto The Front Layout & Wiring Switch - ** This Is The Wiring Diagram To Use While Wiring Your Setup It Is Now Time To Wire The Front, You Will Need To Find A Location To Run Through Your Firewall.
PAGE 6
Firewall & Use Sealed Grommets (Recommended). Or Find An Existing Hole To Run Your Wires. • • Find The Location You Would Like To Mount Your Switch Wire Your Switch With The Remaining Part of The Harness Supplied With Your Recons. Wired Accordingly ** The Fused Power Wire Is Not The Power Wire Being Ran To Power The Reverse Projector Lights (This Should Be A 5 Amp Fuse) • It Is Required At This Time, To Decided Where To Mount The Relay.
PAGE 7
• • • • Connect The Strip of Wire Connected To The Diode To The White Wire From Your Switch (This Will Be The 86 Terminal On The Relay) Run A Power Wire From Your Battery (+) and Install A 15-20AMP Fuse & Holder. (This Will Be The 87 Terminal On Your Relay) Connect The Power Wire That Is Going To The Recon Projector Lights.