Install Instructions for Hub
Batteries Installation
1. Slide down the lower cover
2. Insert 2 x AA batteries (included)
3. Slide back up the lower cover
HUB Wall Installation
1. Detach the HUB from the table stand as shown here below
2. Attach the wall mounting bracket to its location and mark the holes for the mounting screws
3. Place the HUB’s rear mounting pins close to the wall and gently slide down the wall mount
dimples
1 2 3
WARNING! Do not attempt to rotate the HUB on the mounting to avoid physical damage
to
the enclosure.
HUB Table Installation
For table use, connect the table stand to the HUB and place it on the table.
HUB LED Behavior
• GREEN ashes every 2 Sec – OK
• BLUE ashes every 2 Sec – Failure in communication with the TripleGuard Cloud or with any
system’s device
• RED ashes every 2 Sec – Battery status of the backup batteries or one of the devices is low
System Component Synchronization and Activation
TripleGuard devices are installed and activated using the TripleGuard™ Leak Detector App
available on AppStore and Google Play.
This HUB is designed for internal use only and should be installed by an authorized plumber.
Warranty Instructions
Please visit www.rectorseal.com/tripleguard-support for warranty, technical support, terms, and
conditions or troubleshooting. RectorSeal, LLC warrants the TripleGuard (product only) to be free
of defects in workmanship, and material for a period of up to one year from date of purchase.
TripleGuard HUB Installer Guide
Product 97710
RectorSeal
2601 Spenwick Drive - Houston, TX 77055 800-231-3345 rectorseal.com
RectorSeal, the logos and other trademarks are property of RectorSeal, LLC, its afliates or its licensors and are protected by copyright, trademark and other intellectual property laws,
and may not be used without permission. RectorSeal reserves the right to change specications without prior notice. © 2018 RectorSeal. All rights reserved. R50310-0918
G
D F
E
C
B
A
Welcome
Thank you for choosing TripleGuard. TripleGuard SMART is the ultimate IoT cloud-based system
for home safety. The system is managed via an App and is designed to prevent damage due to
water leakage. TripleGuard offers you total peace of mind at home or away.
Please Note
Please read these instructions carefully and follow the system’s installation and commissioning
steps. Maintain this document in a safe place for future reference. Contact your authorized
installer with any questions.
WARNING! This product was designed to prevent damage caused by water leaks and should
be used for this purpose only.
TripleGuard SMART
TripleGuard’s line of products includes innovative battery-operated devices which enable
the automated control of water valves. This unies under the “Smart Home” umbrella. The
TripleGuard HUB serves as a Gateway that ensures a secured communication between the
system devices, TripleGuard™ Leak Detector cloud, and App.
TripleGuard SMART integrates easily into the Smart Home IoT ecosystem, providing a unique
cloud-based secured platform for Water Leak Management.
TripleGuard HUB Specication:
HUB Description
A. Power outlet
B. Table stand
C. Lower cover
D. HUB
E. USB connector (Optional)
F. RGB LED indicator
G. Wall mounting bracket (rear part)
Part Code 97710
Product Description
The secured and reliable TripleGuard HUB communicates with
the connected devices.
Dimensions 10.24 x 2.36 x 5.71 inches (26.01 x 5.99 x 14.50 cm)
Weight 1.21 lbs (548.85 g)
Power Supply External Adaptor Input 110-240 V AC
Operation Voltage
5V (2x AA back up batteries. Up to 8 hours.) Manufacturer
recommends to visually inspect batteries every year.
Operating RF 868/915 MHz
Transmission Range
Open space - Up to 750 ft (230 m)
In enclosed space - up to 390 ft (119 m)
Avoid installing in a metal cabinet.
Working Temperature -4°F to +122°F (-20°C to +50°C)
Certications
FCC ID: 2AFOICLMCTRL10
IC: 20798-CLMCTRL10