Installation Instructions

ManualsBrandsRed Barrel Studio ManualsCeiling LightsSteuben 3 - Light Shaded Classic / Traditional Chandelier

INSTALLATION

AND

SAFETY

INSTRUCTIONS

YOUR

SAFETY

WARNING:

SURE

THE

EIECTRICITY TO THE

WIRES

YOU ARE WORKING

SHUT

OFF;

EITHER

THE FUSE IS

REMOVED OR THE

CIRCUIT

BREAKER

IS SHUT

OFF.

ERAL

You don't need speeial

tools to install this fixture. Be

sure to

the steps

the order

given.

Under no

circumstances

should

fixture

hung

house

electrical wires, nor

should a

swag type

fixture

installed

on a ceiling which

contains a

radiant

type heating system. Read instructions

carefully.

you

are unclear as tc how to

proceed,

consult a

qualified

electrician.

NOTE:

Proper wiring is

essential

for

the safe operation

of this

fixture.

IXTURE ASSEMBLY

Carefully remove the fixture from

the carton and check

that

all

parts

are

included

as shown in figure. Be careful not

to misplace

any of the screws or

parts,

which are needed

to install this

fixture.

'ALLATION

IMPORTANT:

Do not

attach

fixture

directly to

outlet box.

STEP

1: Secure

mounting

bar

(A)

to outlet

box

with

outlet box

screws

(B)"Thread

nut

(D)

onto nipple

(E).

lnsert

lock

washer

(C)

and thread the nipple

(E)

onto

mounting

bar

(A),

then secure with the nut

(D).

STEP 2:

Thread

screw collar ring

(G)

onto

nipple

(E).

Slide

screw

collar

ring

(G)

and canopy

{F)

over screw collar

ring

(G).

Using a

pair

pliers,

open the chain link

(H)

and chain link

(J)

connecl it to coiiar ring

(G),chain

(l)

and

fixture

loop

(K),Close

the chain

link.

BE SLiRE TCI 0LOSE

ALL

cliAiN

LII{KS C3L'lFi,,ETE'

STEP

3:l-ace

wires

up through chain

(H)

and

pass

wires

through holes in screw

collar

ring

(G),We

recommend lacing wire

up through

every other link of

lherlr

(l).

STEP 1:

lnsert the

green grounding

screw into

the

hole with

two

raised

dimples on the mounting

bar. Wrap the

ground

wire

from the fixture

(if

supplied) around the

green

grounding

screw, then connect it

ground

wire from

the outlet box

(if

not fixed

on the outlet box) using a

wire

connector

(not

supplied). lf

ground

wire from the

fixture is

not supplied, wrap

the

ground

wire

(if

not fixed

on the outlet box)

from

the outlet box

around the

green

grounding

screw and tighten it,

NEVER

CONNECT GROUND WIRE TO BLACK

OR WHITE

POWER

SUPPLY

WIRES.

STEP 2:

Take

note

of the color of the wire(s)

your

fixture.

ldentify which

group your

fixture wire(s)

falls into and

nnect the wires

according to the directions

below:

resco

GROUP A:

Connect to Black

House

Wire

GROUP B: Connect

White

House Wire

BLACK

WHITE

'PARALLEL

WIRE

(round

smooth)

*PARALLEL

WIRE

(square

ridoed)

WHITE OR GREY WITH

IRACER

WHITE

OR GREY WITHOUT

TRACER

BROWN

GOLD OR BLACK

r/ITHOUT

TMCER

BROWN,

GOLD OR BLACK

WITH TRACER

"NOTE:

When

parallel

wire

(SPT-I

& SPT-2) is used,

the tracer

wire

is square shaped

ridged

and the

less

tracer wire is round

in shape or smooth

(seen

best

when viewed

from wire end.)

STEP 3:

Take

your

fixture wire(s) from

group

and

place

evenly

against

the

black

wire from

the outlet box. Do NOT

twist

wires

together before using wire connectors.

STEP 4;

Fit

wire

connector

(not

supplied) over"the wires

and

screw the connector clockwise

until

you

feel firmness"

STEP

Try

gently

pull

the connector off the wires. lf

you

can

pull

the connector

off, carefully

re-do

steps 3 and 4 as

above, and check again for

firm

connection.

STEP 6:

Connect the fixture wire from

group

to the

white

wire

from the outlet box in

the same manner, Make

sure no

bare

wires

can be seen outside wire

connectors.

STEP 1:

After wires are

conneeted, tuck them

carefully

inside

outlet box" Raise canopy

(F)

allowing for

nipple

(E)

protrude

through

the

holes

on canopy

(F),

and secure with screw collar ring

(G)"

Thread nipple

(N)

into

coupling

(O),Place

tube

(M),cap

(L)

onto nipple

(N)

and

secure

with loop

(k)"

Put

the

fabric

shaoe

(Q)

over the candle cover

(P).

lnstall light bulbs"

(Please

do not

exceed the

m!414g1!

qpgq{yEqommended

the socket.)

To clean, wipe fixture with

a soft cloth. Clean

glass

with

mild

soap" Do not use abrasive materials

such as scouring

pads

powders,

steel wool or abrasive

paper.

RDERING PARTS

STEP

Keep

this sheet for future reference, and

order replacement

parts.

sure to use

illustration when

ordering

parts.

ease

you

need

exact wording from

F--G

m.-__r-i

fr-.:

'ts-K

r::1^

L__l

I l-*o

,i'

Line

art shown may

not

exactly

match

the fixture

enclosed.

However,

the

installations

do apply to this

fixture.

Summary of content (1 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS YOUR SAFETY WARNING: BE SURE THE EIECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. ERAL You don't need speeial tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully.