Installation & Assembly_1

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-CSE8406
For Style CSE8406PN,CSE8406EK
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)MediumBase100WbulbMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
C
Fixture
Body
x1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
B
Alternate
Mounting
screw
x2
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 1
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 Test Fitting Backplate to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
should be snug against the wall and the Mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate on Fixture Body (C)
is secure, remove the mounting ball and Fixture Body (C).
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
ReleasedDate:2016-10-12
D
Shade
x1
E
Steel
Collar
x1
F
Socket
Collar
x1
STEP 2 - Remove Styrofoam
inside of the Fixture
Body
A.
and D
C
Remove the Package
Material Shade ( )
inside the Fixture Body ( ).
Figure 2
C
D
Package
Material