Assembly & Installation Instructions

ManualsBrandsRed Barrel Studio ManualsLantern Outdoor Wall LightingAlorton Dualux® 1-Light Outdoor Wall Lantern

Page 1/4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING:

TOAVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Metal Frame

Fixture

Ball Nut (G)

Rubber Pad (H)

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

replacing the bulb.

Maximum Wattage: 11W Dimmable LED

Work Temperature: - 4°F~104°F

Hardware Package (included)：

Mounting Screw (B)

Green Grounding

Screw (E)

Wire Nut (F)

Lock Nut (D)

Ball Nut (G)

Rubber Pad (H)

Cross Bar(A)

Headless Screw (C)

Green Grounding Screw (E)

Outlet Box

Wire Nut (F)

Headless Screw (C)

Cross Bar (A)

Mounting Screw (B)

Lock Nut (D)

House Grounding Wire

Fixture Grounding Wire

Fixture Wire

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

Important to Know

Features

Fig.1

Clip

Glass

Curved Arm

Back Plate

Set Screw

Rubber Pad

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TOAVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Important to Know 1. Read all instructions carefully before installation and operation. 2. If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician.
PAGE 2
Installation steps Turn off the power at fuse or circuit box. 1. Thread two headless screws through the cross bar, and then secure them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level. 2. Attach cross bar to outlet box using two mounting screws. 3.
PAGE 3
FIG.1 FIG.2 Manual Override Operation Diagram AUTO Mode Turn wall switch OFF-ON in 3 Seconds Turn wall switch OFF-ON in 3 Seconds again On the back of the sensor Time Manual Override Mode Low Level Sens Test 3H 6H 0 CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
PAGE 4
---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1. Make sure there is no movement that could be picked up by the sensor. 2. Adjust the time knob counterclockwise to reduce the delay shut-off time.